Installation Guide

ManualsBrandsLG Electronics ManualsAppliance partsTrim Kit for Countertop Microwave Oven in Stainless Steel

INSTRUCTIONS FOR THE INSTALLATION OF

MICROWAVE APPLIANCE FRAME

PLEASE READ CAREFULLY BEFORE INSTALLATION

1. The cabinet which is used for the installation of the microwave oven

appliance should be securely attached to the back panel to ensure

stability.

2. The cabinet is to be used for microwave oven with a maximum weight of

approximately 30kg.

3. If the microwave is installed directly above a refrigerator or freezer

cabinet pay attention to their installation instructions, a ventilation duct

must also be in place.

4. If the microwave appliance is installed directly above an electric built in

oven the appropriate electric oven installation guide must be observed.

CAUTION : In the case of frequent or particularly long grill operation

times of the electric oven (especially with door open), the shape and

colour of the microwave oven and installation frame can change.

5. If the microwave oven is used again as a ‘table appliance all appropriate

detachable accessories must be removed.

6. The oven should not be used as a storage place for food, cooking

utensils etc. In the case of misuse damage or hazard could occur.

7. If a fault occurs to an electronic or electrical component, the oven can

only be turned off by pulling out the mains plug or appropriate circuit

breaker (upstream automatic fuse).

ELECTRICAL CONNECTION

Once the oven is securely attached it is ready for plugging in and must be

connected to a properly installed safety socket. If any relocation of a socket or

exchange of connection line is required it must be made by a qualified electric titter

taking into consideration the appropriate regulations. If after installation the

appliance’s plug is too short a separator controlling all poles must be used at the

installation side with a contact opening of at least 3mm with regard to satisfying the

necessary safety regulations.

PARTS LIST

(A) 1 Each

(B) 1 Each

(D) 23 Each

(E) 6 Each

(F) 1 Each

(G) 1 Each

(H) 1 Each

(I) 1 Each

(J) 1 Each

P/No. :MFL38268403 Printed in China

Trim Frame

Bottom Duct

Side Duct

4 mm x 12 mm

Round-Head Screws

4 mm x 14 mm

Flat-Head Screws

Anti-Tip Bracket

Anti-Tip Brace

Upper Duct

Top Bracket

Bottom Bracket

(K) 2 Each

Templates

1/2 ″down the face of

Summary of content (4 pages)

PAGE 1
ELECTRICAL CONNECTION INSTRUCTIONS FOR THE INSTALLATION OF MICROWAVE APPLIANCE FRAME Once the oven is securely attached it is ready for plugging in and must be connected to a properly installed safety socket. If any relocation of a socket or exchange of connection line is required it must be made by a qualified electric titter taking into consideration the appropriate regulations.
PAGE 2
FIG 1 1.DIMENSIONS OF THE INSTALLATION OPENING (FIG 1) 11⁄ 8″ Overlap The following opening dimensions in feet must be available in the installation cabinet : HEIGHT :163⁄4.″ , WIDTH : 251⁄ 2″. , DEPTH : 191⁄ 2″. or 22. Depth 27″ Models:11⁄ 16″ overlap 30″ Models: 21⁄ 16″ overlap WARNING: This trim kit uses air flow from the top, bottom and sides of the trim frame. Blocking the air flow can cause the microwave to function improperly and may cause damage to the microwave.
PAGE 3
FIG 4 4.INSTALL SIDE DUCT AND UPPER DUCT( FIG 4) Upper Duct 1.Connect the side duct to the upper duct as shown. (1 ) Insert projecting tabs of the upper duct into the holes of the side duct. (2) Bend the tabs up with caution as shown. NOTE: Remove any oil or dirt on the surface of the microwave oven before the ducts are attached. 2.Set the microwave upright, being careful not to bend the front flange. Remove the one existing screw from the left side of the microwave oven. 3 Tabs Cutout Opening (1) 3.
PAGE 4
FIG 7 7.INSTALL THE TOP BRACKET (FIG 7) 1.Place the top bracket flange on top of the upper duct with the opening of the top bracket lined up with the opening on the upper duct. 2.Align the center line marking on the top bracket with the center line drawn on the top front face of the cabinet at the center of the cutout. 3.Ensure the top bracket is level and mark screw hole locations on the cabinet face. 4.Drill pilot holes through the side holes in the top bracket.