PLASMA MONITOR OWNER’S MANUAL MODELS: MP-42PZ44/44H/45M/45V MP-42PZ44A/44HA/45MA/45VA MP-42PZ44B/44HB/45MB/45VB MP-42PZ44K/44HK/45MK/45VK MP-42PZ44R/44HR/45MR/45VR MP-42PZ44S/44HS/45MS/45VS MP-42PZ90/90H/91M/91V MP-42PZ90A/90HA/91MA/91VA MP-42PZ90B/90HB/91MB/91VB MP-42PZ90K/90HK/91MK/91VK MP-42PZ90R/90HR/45MR/91VR MP-42PZ90S/90HS/91MS/91VS Please read this owner’s manual thoroughly before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor.
Safety Instructions Safety Instructions * Safety instructions have two kinds of information, and each meaning of it is as below. WARNING The violation of this instruction may cause serious injuries and even death. NOTES The violation of this instruction may cause light injuries or damage of the product. Take care of danger that may happen under specific condition. WARNING W 1. Do not place the Monitor in direct sunlight or near heat sources such as heat registers, stove and so on.
Safety Instructions NOTE 1. Never touch the power plug with a wet hand. This may cause an electric shock. 8. Ensure the power cord doesn’t trail across any hot objects like a heater. This may cause a fire or an electric shock. 2. Disconnect from the mains and remove all connections before moving. 3. Do not place the Monitor in a built-in installation such as a bookcase or rack. 9. Do not plug when the power cord or the plug is damaged or the connecting part of the power outlet is loose.
Contents Contents Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2~3 Introduction Controls and Connection Options . . . . . . . . . . . .6 Remote Control Key Functions . . . . . . . . . . . . . .7 Installation Installation Instruction . . . . . . . . . . . . . . . . . . . .9~10 External Equipment Connections . . . . . . . . . .11~14 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Introduction What is a Plasma Display Panel (PDP)? If voltage is applied to gas within glass panels, ultraviolet rays are produced and fused with a fluorescent substance. At that instant, light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160° - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room.
Introduction Controls Front Panel Controls - This is a simplified representation of front panel. Here shown may be somewhat different from your monitor. INPUT SELECT ON/OFF MENU VOL. E, D Main Power Button INPUT SELECT Button Buttons VOLUME (F,G) Buttons MENU Button Remote Control Sensor Power Standby Indicator Illuminates red in standby mode, Illuminates green when the Monitor is turned on Connection Options - Connection panels shown may be somewhat different from your monitor.
Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the monitor. - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary. POWER Switches the monitor between ON and STANDBY. INPUT SELECT Selects source: Video, S-Video, Component, RGB, or DVI mode. MULTIMEDIA Selects: Component, RGB, or DVI mode. APC Adjusts the factory preset picture according to the room.
Installation Installation Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. POWER 1.5V 1.5V SLEEP Batteries DASP PIP ARC PIP TWIN PICTURE VOL Owner’s Manual INPUT SELECT APC ARC SUB INPUT SWAP MENU BNC-RCA adapter MUTE OK 1 2 4 5 7 8 VOL 3 6 9 0 POWER STOP P/STILL REW PLAY FF REC WIN.SIZE WIN.
Installation Installation Instructions • The Monitor can be installed in different ways such as on a wall, or on a desktop etc. • Install this monitor only in a location where adequate ventilation is available. • It is recommended that MP-42PZ44/45V/90/91V series models only be used at an altitude of less than 3281 feet (1000m) to get the best quality picture and sound.
Installation Installation Instructions continued Wall Mount: Vertical Vertical installation (MP-42PZ45M/45V/91M/91V series models only) Detailed installation instructions are included in the optional Vertical Wall Mounting Bracket Installation and Setup Guide, see your dealer. NOTE: When installing the monitor vertically, the front panel controls must be in the left side position.
Installation External Equipment Connections NOTE: All cables shown are not included with the plasma display. VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor - Use the ISM Method feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed image may remain visible on the screen. How to connect 1.
Installation External A/V Source Setup How to connect 1. Connect the provided BNC-RCA adapter to the monitor’s VIDEO INPUT. 2. Connect the audio and video cables from the external equipment's output jacks to the monitor input jacks, as shown in the figure. When connecting the monitor to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).
Installation PC Setup - This Plasma display provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitor sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol. How to connect 1. To get the best picture quality, adjust the PC graphics card to 800x600, 60Hz. 2.
Installation Monitor Display Specifications (RGB-PC /DVI-PC Mode) Resolution 640x350 720x400 640x480 848x480 852x480 14 Plasma Monitor Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 Resolution 85.08 800x600 Horizontal Vertical Frequency(KHz) Frequency(Hz) 35.156 56.25 37.879 60.31 31.469 70.08 48.077 72.18 37.927 85.03 46.875 75.00 31.469 59.94 53.674 85.06 35.000 66.66 49.725 74.55 37.861 72.80 48.363 60.00 37.500 75.00 56.476 70.06 43.269 85.
Operation Operation - A inactive menu options aren’t available in this monitor. It’s only available to connect with PDP Tuner (RP-BA50). Turning on the Monitor Turning on the Monitor just after installation 1. Connect power cord correctly. 2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standby mode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT, MULTIMEDIA button on the remote control to switch the Monitor on.
Operation Picture Menu Options - Each adjustment for the Picture menu options doesn’t effect other input sources. Readjust Picture menu options for each of the following sources. • RGB (PC) / DVI (PC), • RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i) • Video / S-Video / Component (480i) APC (Auto Picture Control) - APC adjusts the Monitor for the best picture appearance. - When adjusting picture options (contrast, brightness, color, sharpness and tint) manually, APC automatically changes to User.
Operation Sound Menu Options DASP (Digital Auto Sound Processing) - This function lets you enjoy the best sound without any special adjustment because the Monitor has the appropriate sound options based on the program content. - When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to User. 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below. Flat Music Movie Sports User • You can also adjust DASP in the SOUND menu.
Operation T imer Menu Options Clock Setup - If current time setting is erased by a power failure, if TV is unplugged or if the monitor is turned off with the ON/OFF button on the monitor, reset the clock. 1. Press the MENU button and then use D /E button to select the TIMER menu. TIMER 2. Press the G 3. Press the 4. Press the button and then use D /E button to select Clock. G button and then use D /E button to set the hour. G button and then use D /E button to set the minutes.
Special Menu Options Key Lock - The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by disabling the front panel controls. - This Monitor is programmed to remember which option it was last set to even if you turn the monitor off. 1. Press the MENU button and then use D /E button to select the SPECIAL menu. 2. Press the G button and then use D /E button to select Key lock. 3.
Operation Special Menu Options continued Low Power - Low power reduces the plasma display power consumption. 1. Press the MENU button and then use D /E button to select the SPECIAL menu. 2. Press the G button and then use D /E button to select Low power. 3. Press the G button and then use D /E button to select On or Off. SPECIAL Language Key lock ISM Method Low power G Set ID On Off Caption / Text • When you select On, the screen darkens. Captions 4. Press the ENTER button to save.
Operation Screen Menu Options Auto Adjustment - RGB (PC) mode only; This function doesn’t work for RGB-DTV mode. Automatically adjusts picture position and minimizes image shaking. After adjustment, if the image is still not correct, your Monitor is functioning properly but needs further adjustment. The Auto config. and Manual config. are not active in DVI mode. 1. Press the MENU button and then use D /E 2. Press the G button and then use button to select Auto config..
Operation Screen Menu Options continued Adjusting Horizontal/ Vertical Vertical Position - This function works in the following modes: RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i). SCREEN Auto config. ARC 1. Press the MENU button and then use D /E button to select the SCREEN menu. Zoom in/out Position 2. Press the G button and then use D /E 3. Press the G button and then use D /E /F /G button to select Position. button to adjust the position. 4.
Operation Luminance Noise Reduction (Video, (Video, S-video and Component 480i modes only) - Use YNR to reduce the picture noise that may appear on the screen. 1. Press the MENU button and then use 2. Press the G button and then use 3. Press the G button and then use D /E D /E D /E button to select the SCREEN menu. SCREEN button to select YNR. Auto config. ARC button to select On or Off. Zoom in/out 4. Press the ENTER button to save. Position Manual config. Screen adj.
Operation PIP (Picture-In-Picture) Feature - PIP lets you view 2 different inputs pictures (sources) on your monitor screen at the same time. One source will be large, and the other source will show a smaller inset image. - You can also adjust the PIP features in the PIP/DW menu (Except Swap function). Watching PIP Swapping the PIP Press the PIP button repeatedly to turn PIP on or off. Press the SWAP button to exchange the main and sub pictures.
Operation Double W indow Setup Options - As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at the same time. Each source is given half the screen. Watching Double Window Window Press the DW button repeatedly to select one of the Double Window options. DW 1 DW 2 Sub Picture Size Adjustment Press the WIN.SIZE button. • Use the F / G button to change the sub picture size. • Using the Win.
External Control Device Setup External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor.
External Control Device Setup Set ID Use this function to specify a monitor ID number. Refer to ‘Real Data Mapping 1’. See page 28. SPECIAL Language 1. Press the MENU button and then use D /E button to select the SPECIAL menu. 2. Press the G button and then use button to select Set ID. Key lock ISM Method D /E Low power G 3. Press the G button and then use F / G button to adjust Set ID to choose the desired monitor ID number. The adjustment range of Set ID is 1 ~ 99. Set ID 4.
External Control Device Setup 01. Power (Command2:a) 04. Screen Mute (Command2:d) G To control Power On/Off of the Monitor. G To select screen mute on/off. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off [k][d][ ][Set ID][ ][Data][Cr] 1 : Power On Acknowledgement Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) [a][ ][Set ID][ ][OK][Data][x] Acknowledgement [d][ ][Set ID][ ][OK][Data][x] G To show Power On/Off. Transmission 05.
External Control Device Setup 08. Brightness (Command2:h) 13. Remote Control Lock Mode (Command2:m) G To adjust screen brightness. You can also adjust brightness in the Picture menu. G To lock the remote control and the front panel controls on the monitor. Transmission Transmission [k][h][ ][Set ID][ ][Data][Cr] [k][m][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping 1’. See page 28.
External Control Device Setup 17. PIP Position (Command2:q) 21. Color Temperature (Command2:u) G To select sub picture position for PIP. You can also adjust the sub picture position using WIN.POSITION on the remote control or in the PIP/DW menu. G To adjust color temperature. You can also adjust ACC in the Picture menu.
External Control Device Setup 25. PIP Input Select (Command2:y) 29. Orbiter Time Setting (Command2:r) G To select input source for sub picture in PIP mode. G To adjust orbiter operation time term. Transmission Transmission [k][y][ ][Set ID][ ][Data][Cr] [j][r][ ][Set ID][ ][Data][Cr] Data 0 : RGB 1 : Component 2 : Video 3 : S-Video 4 : DVI Data Min: 1 ~ Max: FE • Refer to ‘Real data mapping 1’. See page 28.
IR Code IR Code How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code G Output waveform Single pulse, modulated with 37.
IR Code Code (Hexa) 00H 01H 02H 03H 08H C4H C5H 09H 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 0BH 98H D5H C6H BFH 5AH D8H 0EH 44H 43H 52H 4DH 60H 61H 63H 64H 6BH 40H 41H 69H 6AH 7BH 79H 76H 77H AFH 99H Function UP (D) DOWN (E) VOL+ (G) VOL- (F) POWER ON/OFF POWER ON POWER OFF MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 INPUT SELECT MULTIMEDIA RGB DVI Component Video S-video SLEEP ENTER (Á) MENU DASP APC PIP PIP INPUT
Troubleshooting Checklist Troubleshooting Checklist • Check whether the Monitor is turned on. No picture & No sound • Power cord inserted into wall outlet? • Test the wall power outlet, plug other product’s power cord into the wall outlet where the Monitor’s power cord was plugged in. Picture OK & No sound • Press the VOLUME (G) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the Plasma Display and the remote control causing obstruction.
Specification Product Specifications MODEL MP-42PZ44/44A/44B/44K/44R/44S MP-42PZ44H/44HA/44HB/44HK/44HR/44HS MP-42PZ45M/45MA/45MB/45MK/45MR/45MS MP-42PZ45V/45VA/45VB/45VK/45VR/45VS MP-42PZ90/90A/90B/90K/90R/90S MP-42PZ90H/90HA/90HB/90HK/90HR/90HS MP-42PZ91M/91MA/91MB/91MK/91MR/91MS MP-42PZ91V/91VA/91VB/91VK/91VR/91VS Width (inches / mm) 40.7 / 1033 Height (inches / mm) 24.5 / 622 Depth (inches / mm) 3.
PLASMA MONITOR OWNER’S MANUAL MODELS: MP-42PZ44/44H/45M/45V MP-42PZ44A/44HA/45MA/45VA MP-42PZ44B/44HB/45MB/45VB MP-42PZ44K/44HK/45MK/45VK MP-42PZ44R/44HR/45MR/45VR MP-42PZ44S/44HS/45MS/45VS MP-42PZ90/90H/91M/91V MP-42PZ90A/90HA/91MA/91VA MP-42PZ90B/90HB/91MB/91VB MP-42PZ90K/90HK/91MK/91VK MP-42PZ90R/90HR/45MR/91VR MP-42PZ90S/90HS/91MS/91VS Please read this owner’s manual thoroughly before operating the Monitor. Retain it for future reference. Record model number and serial number of the Monitor.