User’s Guide Network Monitor N1742L N1942L Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service.
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards Power Cord (Depending on the country) 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) IMPORTANT This accessories may look different from those shown here.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. Hinge Body Stand Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.
Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on the surface. 3. cushion or soft cloth. Change your lock on the product as it follows and turn it in the arrow direction. If you can't release the stand base even the locking knob is at a release position, Please push the indicated knob down and retry it. 4. Pull out the Stand to remove.
Connecting the Display 5. Pushing the PUSH button, Take the stand base from stand body. Warning: You can hurt your finger. Good Position Bad Position Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort.
Connecting the Display Using the Computer NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. 1. A Connect D-sub(RGB Analog) Cable (PC) B Connect D-sub(RGB Analog) Cable (Mac) Analog signal X-PORT D-sub Wall-outlet type A B Mac adapter (This item must be purchased separately.
Connecting the Display Using the Monitor 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . 1 Connect peripheral devices 2 Connect LAN Cable (X550 port) Analog signal X-PORT D-sub Wall-outlet type Keyboard/Mouse Input LAN cable should be connected before booting PC.(This item must be purchased separately.) (Make sure to connect X550 port,not LAN port of PC) WX550 port Up to 5 ports are supported per X550 PCI Card.
Connecting the Display NOTE LAN Cable -For the LAN cable,it is recommended to use SFTP (recommend : 6m, max : 10 m) provided by LG. Image quality and some functionality may be degraded if a different LAN cable is used. -To achieve good image quality,avoid using UTP and STP cables. -You must use a direct LAN cable,not a crossover one. Both connections should be same colors. Do not connect any kind of network devices.
Connecting the Display Connecting to a X550 port using a LAN cable. Notice Turning the power off while booting the PC may damage the product. Turning the power off while booting the PC may cause it to operate incorrectly. If the mouse is connected using a USB device and is not detected, disconnect and connect it again. If you reconnect a peripheral device such as a keyboard, mouse or LAN cable while the PC is in operation, the device may not work properly.
Control Panel Functions Front Panel Controls MENU AUTO/SET SOURCE VOLUME Control MENU Button Function Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds.
Control Panel Functions Control SOURCE Function Use these buttons to select or adjust functions in the On Screen Display. Use this button to make either D-Sub or X-PORT connector active. This feature is used when two input sources are connected to the display. VOLUME Use these buttons to select or adjust functions in the On Screen Display. • X-PORT : When X-PORT signal is active,Use button to decrease or increase the speaker volume on X-PORT input. • D-sub : This menu is not available.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description POSITION POSITION POSITION HORIZONTAL To move image left and right. VERTICAL To move image up and down. MENU : Exit : Decrease : Increase SET : Select another sub-menu TRACKING TRACKING MENU : Exit : Decrease : Increase SET : Select another sub-menu CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display.
On Screen Display(OSD) Selection and Adjustment Main menu SETUP Sub menu Description SETUP LANGUAGE To choose the language in which the control names are displayed. OSD POSITION To adjust position of the OSD window on the screen. WHITE BALANCE If the output of the video card is different from the required specifications, the color level may deteriorate due to video signal distortion.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu USER Description MOVIE This feature lets you easily select the best desired INTERNET image condition optimized to the environment (ambient illumination, image types etc). MOVIE: For animation images in videos or movies INTERNET: For text images (Word processing etc.) MENU : Exit : Decrease : Increase SET : Select another sub-menu USER User You can manually adjust ACE or RCM.
Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? ● Is the power indicator light on? • Press the Power button. ● Is the power indicator flickering? • If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. (X-PORT support only 16bits color) - “White Balance” is performed on black/white pattern. - Check if the screen is set to normal mode. ● The screen blinks.
Specifications Display Sync Input N1742L 17 inches (43.2 cm) Flat Panel Active matrix-TFT LCD, AntiGlare coating Visible diagonal size: 43.2 cm 0.264 mm pixel pitch Horizontal Freq. 30 - 66 kHz (Automatic) Vertical Freq. 57 - 63 Hz (Automatic) D-SUB support 60Hz only(except Dos mode) 1440 x 900 (60Hz) 1280 x 720 (60Hz) X-PORT 1280 x 1024 (60Hz) 800 x 600 (72Hz) 1024 x 768 (60Hz) D-SUB Video Input D-SUB Signal Input Input Form X-PORT Signal Input Input Form 15 pin D-Sub Connector RGB Analog (0.
Specifications Display N1942L 19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD, AntiGlare coating Visible diagonal size: 48.2 cm 0.294 mm pixel pitch Sync Input D-SUB Video Input Horizontal Freq. 30 - 66 kHz (Automatic) Vertical Freq. 57 - 63 Hz (Automatic) D-SUB support 60Hz only(except Dos mode) 1440 x 900 (60Hz) 1280 x 720 (60Hz) X-PORT 1280 x 1024 (60Hz) 800 x 600 (72Hz) 1024 x 768 (60Hz) D-SUB Signal Input 15 pin D-Sub Connector Input Form RGB Analog (0.
Specifications D-SUB Preset Modes (Resolution) Display Modes (Resolution) 1 2 3 4 5 *6 Horizontal Freq. (kHz) 31.469 31.468 31.469 37.879 48.363 63.981 640 x 350 720 x 400 640 x 480 800 x 600 1024 x 768 1280 x 1024 Vertical Freq.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. Place the monitor with its front facing downward on a soft cloth. 2. Separate the stand by pushing the PUSH button. Good Position 3. Bad Position Warning: You can hurt your finger. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate.
Digitally yours
