ENGLISH OWNER’S MANUAL NETWORK MONITOR Please read this manual carefully before operating your set and retain it for future reference. NETWORK MONITOR MODEL N224WHA www.lg.
Accessories Thank you for purchasing this LGE product Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. OWNER'S MANUAL /Cards 15-pin D-SUB Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) Or Power Cord AC-DC adapter (Depending on the country) AC-DC adapter (Depending on the country) USB Extension Cable IMPORTANT This accessories may look different from those shown here.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a cushion or soft cloth. 2. Assemble the Stand Base into the Stand Body. Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. Stand Body Side Stand Base Stop Pin FRONT 3. Make the monitor stand , then pull out the Stop Pin.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -6˚ to 17˚ -6˚ 17˚ Height Range: maximum 4.33 inch (110.0 mm) 110.0 mm First, remove the locking pin.
Connecting the Display Using the Pivot function -The pivot function allows you to rotate the screen 90 degrees clockwise. 1. Lift the monitor to its highest height to utilize the Pivot function. 2. Landscape & Portrait : You can rotate the panel 90 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function. If the monitor head touches the Stand Base, then the Stand Base could crack. Head section Stand section 3.
Connecting the Display Connecting to the Computer 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. A Connect D-SUB(RGB Analog) Cable (PC) Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure.
Connecting the Display Connecting to the Computer Using LAN 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect peripheral devices USB 1.1 port (Only for keyboard and mouse) B Connect LAN Cable USB 2.0 port (Only for USB memory stick) Wall-outlet type signal input cables OR Wall-outlet type switch hub LAN Cable Type - Standard : IEEE 802.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off.
Control Panel Functions Front Panel Controls MUTE Button • LAN : This menu is available, use this button to switch the sound on or off. or • D-SUB : This menu is not available. MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear.
Control Panel Functions ( ) SOURCE Use these buttons to select or adjust functions in the On Screen Display. Use this button to make either D-SUB or LAN connector active. This feature is used when two input sources are connected to the display. ( ) VOLUME Use these buttons to select or adjust functions in the On Screen Display. Use buttons to decrease or increase the speaker volume on LAN input. AUTO/SET Button Use this button to enter a selection in the On Screen Display.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display blackish images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR PRESET Select the screen color.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description POSITION HORIZONTAL To move image left and right. VERTICAL To move image up and down. MENU : Exit : Decrease : Increase SET : Select another sub-menu TRACKING MENU : Exit : Decrease : Increase SET : Select another sub-menu CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the control names are displayed. OSD POSITION To adjust position of the OSD window on the screen. WHITE BALANCE If the output of the video card is different from the required specifications, the color level may deteriorate due to video signal distortion.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description MOVIE This feature lets you easily select the best desired INTERNET image condition optimized to the environment (ambient illumination, image types etc). MOVIE: For animation images in videos or movies INTERNET: For text images (Word processing etc.) MENU : Exit : Decrease : Increase SET : Select another sub-menu USER User You can manually adjust ACE or RCM.
Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the display onnected? • Check and see if the power cord is connected properly to the power outlet. ● Is the power indicator light on? • Press the Power button. ● Is the power indicator flickering? • If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. - “White Balance” is performed on black/white pattern. - Check if the screen is set to normal mode. ● The screen blinks.
Specifications Display 55.9 cm (21.9 inch) Flat Panel Active matrix-TFT LCD, AntiGlare coating Visible diagonal size: 55.9 cm 0.282 mm x 0.282 mm pixel pitch Horizontal Freq. Vertical Freq. Sync Input Video Input Resolution 30 kHz to 66 kHz (Automatic) 57 Hz to 63 Hz (Automatic) D-SUB Signal Input 15 pin D-SUB Connector Input Form RGB Analog (0.
Specifications Preset Modes (Resolution) - D-SUB (Analog) Display Modes (Resolution) 1 2 3 4 5 6 *7 Horizontal Freq. (kHz) 31.469 31.468 37.879 48.363 55.935 64.674 65.290 640 x 480 720 x 400 800 x 600 1024 x 768 1440 x 900 1680 x 1050 1680 x 1050 Vertical Freq.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. Place the monitor with its front facing downward on a soft cloth. 2. Separate the stand after firstly separating 4 screws by using a driver as figure.
Installing the Wall mount plate 3. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased.LG recommends that wall mounting be performed by a qualified professional installer. Wall Mount pad Hole spacing : 75 mm x 75 mm.
Make sure to read the Safety Precautions before using the product. Keep the OWNER’S MANUAL(CD) in an accessible place for furture reference. The model and serial number of the SET is located on the back or one side of the SET. Record it below should you ever need service. MODEL SERIAL W i t h LG E N e t w o r k M o n i to r, s o m e P C programs may not be compatible or need to be modified due to different kind of operation.
