Owner's Manual LG Minibeam DLP Projector Please read the safety information carefully before using the product. PW600G PW800G P/No : SAC37034620 (1607-REV00) www.lg.
LICENSE LICENSE Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. This DivX Certified® device has passed rigorous testing to ensure it plays DivX® video. To play purchased DivX movies, first register your device at vod.divx.com. Find your registration code in the DivX VOD section of your device setup menu.
ING/CAUTION ELECTRIC SHOCK O NOT OPEN SAFETY INSTRUCTIONS 3 SAFETY INSTRUCTIONS Please take note of the safety instructions to prevent any potential accident or misuse of the projector. yy Safety precautions are given in two forms, i.e. WARNING and CAUTION as detailed below. WARNING Failure to follow the instructions may cause serious injury and even death. CAUTION Failure to follow the instructions may cause injury to persons or damage to the product.
SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Indoor Installation WARNING yy Do not use the projector outside and do not expose the product to any humidity or water. - Since the product is not waterproof, this may result in a fire or electric shock. yy Do not place the projector in direct sunlight or near heat sources such as radiators, fires, stoves, etc. - This may result in fire.
SAFETY INSTRUCTIONS Power WARNING yy The appliance plug is used as the disconnect device. - Please make sure the device is installed near the wall outlet to which it is connected and that the outlet is easily accessible. yy The grounding wire should be connected. - Ensure that you connect the grounding cable to avoid electric shock. If it is not possible to ground the unit, have a qualified electrician install a separate circuit breaker.
SAFETY INSTRUCTIONS yy Do not turn the projector on or off by plugging in the power plug or unplugging it from the power outlet. (Do not use the power plug as a switch.) - This may result in electric shock or damage to the product. yy Do not insert a conductor into the other side of the wall outlet while the power plug is inserted into the wall outlet. In addition, do not touch the power plug immediately after it is disconnected from the wall outlet. - This may result in electric shock.
SAFETY INSTRUCTIONS yy Do not look directly into the lens when the projector is in use. - The bright light may damage your eyes. yy When the lamp is on or has just been turned off, avoid touching the air vent or lamp, because these will be very hot. yy If there is a gas leak in the room with the projector, do not touch the projector or power outlet. Open the windows for ventilation. - Sparks may cause fire or burns. yy Unplug the power cord from the outlet during a lightning storm.
SAFETY INSTRUCTIONS yy Do not start the projector with the volume turned up high. - High volume may damage hearing. yy Do not use high voltage electrical equipment near the projector, (e.g., a bug zapper). This may result in product malfunction. Cleaning WARNING yy Do not spray the projector with water when cleaning. Make sure water does not flow into the projector. - This may result in fire or electric shock.
SAFETY INSTRUCTIONS Others WARNING yy Some users may experience a seizure or other abnormal symptoms when they are exposed to a flashing light or particular patterns from a video game. yy When you go out, place the projector out of reach of animals, and remove the power plug from the wall outlet. - Using a damaged power cord may result in short circuit or fire. yy Do not use the projector near highprecision electronic devices or those that transmit weak radio signal.
SAFETY INSTRUCTIONS CAUTION yy Do not use or store the projector outdoors for long periods of time. yy Be sure to unplug if the projector is not to be used for a long period. - Accumulated dust may result in fire or electric shock due to overheating, ignition, or poor insulation. yy Only use the specified type of battery. - Burst or leaking batteries may result in damage or injury. yy Make sure you use the same type of battery when replacing.
CONTENTS 11 CONTENTS LICENSE 2 SAFETY INSTRUCTIONS 3 ENTERTAINMENT 30 Using SCREEN SHARE 30 MY MEDIA 31 Before Using -- Connecting a USB Device -- Removing a USB Device 31 31 31 To Use My Media -- Watching the Videos -- Viewing the Photos -- Listening to Music -- Viewing Files 33 36 41 44 46 3D FUNCTION 48 While Watching 3D 48 PREPARATION 13 Accessories 13 Optional Extras 14 Parts and Components 15 Using the Joystick Button -- Basic Functions -- Adjusting the Menu 17 17 17 Proj
CONTENTS CONNECTING DEVICES 67 Connecting to HD Receiver, DVD, VCR Player, or External Devices -- HDMI Connection -- HDMI to DVI Connection -- AV Connection -- Component Connection 68 68 68 69 69 Connecting a PC -- HDMI Connection -- HDMI to DVI Connection -- RGB Connection 70 70 70 71 Connecting a Laptop -- HDMI Connection 72 72 Connecting to Headphones 73 Using the Mirroring Function of a Mobile Phone 74 -- MHL/Slimport Connection 74 MAINTENANCE 75 Cleaning -- Cleaning the Lens -- Cleani
PREPARATION 13 PREPARATION Accessories Accessories included with the projector are show below. The pictures may differ slightly from the actual product. Accessories are subject to change without prior notice. New accessories may be added or old ones removed. 219'4 +0276 /76' 2#)' 81.7/' #761 $.#01- ':+6 ꕣ 5'66+0)5 3 /'07 56+.. 4#6+1 *'.2 -'; 5 & 75$ -'; 5 .
PREPARATION Optional Extras To purchase optional accessories, visit an electronics store or online shopping site or contact the retail store where you purchased the product. Optional accessories are subject to change without prior notice.
PREPARATION 15 Parts and Components The projector is manufactured using high-precision technology. You may, however, see tiny black dots and/or bright colored dots (red, blue, or green) that continuously appear on the projector screen. This is a normal result of the manufacturing process and does not indicate a malfunction. Joystick Button Speakers Vent1) Lens Vent1) 2) Focus ring 1) Due to the high temperature of the vent area, do not get close to the vent area.
PREPARATION RGB IN Port (Headphone Port) Port AV IN Port (USB Port) DC IN Port
PREPARATION 17 Using the Joystick Button You can operate the projector by pressing the button or moving the joystick left, right, up, or down. Basic Functions Power On When the projector is turned off, place your finger on the joystick button, press it once, and release it. Power Off When the projector is turned on, place your finger on the joystick button, press it once for a few seconds, and release it.
PREPARATION Projector Status Indicators LED Power Indicator Red Off LED Power Indicator Power standby state The projector is operating with the power on.
PREPARATION 19 Installation Installation Precautions yy Place the projector in a well-ventilated environment. - To prevent internal heat build-up, install the projector in a wellventilated place. Do not place anything near the projector as this may block its air vents. If the air vents are blocked, the internal temperature will increase. - Do not place the projector on a carpet or rug. If the vent is on the bottom, use the projector on a solid level surface and ensure the vent is not blocked.
PREPARATION Projection Distance per Screen Size 1 Place the projector on a sturdy, level surface, together with the PC or audio/video source. 2 Place the projector an appropriate distance away from the screen. The distance between the projector and the screen determines the actual size of the image. 3 Position the projector so that the lens is at a right angle to the screen. If the projector is not at a right angle, the projected image will look distorted.
PREPARATION 21 How to Install the Projector On a Tripod yy You can install this projector using a camera tripod. As shown below, you can mount the projector instead of a camera on the tripod. yy When stabilizing the tripod, we recommend using a locking bolt of standard size 4.5 mm or less. The maximum size allowed for the locking bolt is 5.5 mm. (If it is longer than the maximum allowed size, it may damage the projector.
PREPARATION Caution when Using Pouch * Available for the PW800G model only. The purpose of the pouch provided is to protect the exterior of the product. Please insert the back of the product first into the pouch as illustrated. NOTE yy When using the product with the pouch on for a long period of time, the parts exposed to direct sunlight may change colors. yy When using the product with the pouch on, the built-in speakers may sound low in volume.
REMOTE CONTROL 23 REMOTE CONTROL Open the lid at the back of the remote control and insert the batteries as described in the instructions. Use new batteries. ① 219'4 +0276 /76' 2#)' 81.7/' #761 $.#01- ':+6 ꕣ 5'66+0)5 3 /'07 56+.. 4#6+1 *'.2 -'; 5 & 75$ -'; 5 . 4 ② POWER Turns the projector on or off. MUTE Mutes the sound of the projector. INPUT Changes the input source. VOLUME +, Adjusts the volume level. PAGE , Moves to the previous/next page.
REMOTE CONTROL 219'4 +0276 /76' 2#)' 81.7/' #761 $.#01- ':+6 ꕣ 5'66+0)5 3 /'07 56+.. 4#6+1 *'.2 -'; 5 & 75$ -'; 5 . 4 STILL Freezes the moving image. (Available in any mode other than USB mode.) RATIO Changes the aspect ratio of the screen per pressing of the button. USB Accesses USB mode. HELP Enables the self-diagnosis. KEY.S ▲, ▼ Adjusts the Keystone function. Playback control buttons Controls playback of MY MEDIA. Color buttons Sets detailed settings or gesture for each menu.
USING THE PROJECTOR 25 USING THE PROJECTOR Watching Projector Turning on the Projector The menu screen display in this owner's manual is an example to help users understand how to operate the product and may look different from the actual screen. 1 2 Connect the power cord correctly. 3 In the Language Selection screen, select a language. After waiting for a moment, press the POWER button on the remote control or the joystick button.
USING THE PROJECTOR Focus of the Screen Image When an image appears on the screen, check if it is in focus and fits the screen properly. Adjust the focus of the image by rotating the Focus Ring to the left or right. Make sure the product does not move when adjusting the focus. Focus Ring Watching Projector 1 In standby mode, press the POWER button to turn the projector on. 2 Press the INPUT button and select the input signal you want.
USING THE PROJECTOR Additional Options Adjusting Aspect Ratio yy Resize an image to view at its optimal size by pressing RATIO while you are using the projector. NOTE yy Available picture size may differ depending on the input signal. yy You can also use the Q.MENU or SETTINGS button. Menu 16:9 Description Resizes images to the 16:9 ratio. Full Changes to the full screen regardless of the aspect ratio. Just Displays video images in Scan the original size without removing parts of the edge of the image.
USING THE PROJECTOR Changing Input Device Selecting an Input Label Displays which devices are connected to which input ports. To select an external input Selects external input. The illustration of the menu may differ from the actual screen on the product. yy Press the INPUT button on the remote control to display the input selection screen. - Connected inputs are displayed first. However, AV / Component / SCREEN SHARE input is always activated. ( SCREEN SHARE is available for the PW800G model only.
USING THE PROJECTOR Blank Function Using the Blank Function This function may be effective when you need to draw attention during a meeting or training. 1 Press the BLANK button, and the screen is covered by the background color. You can change the background color by referring to Selecting a Blank Image. 2 Press any button to clear the blank function. To cover the screen temporarily, press the BLANK button on the remote control. Do not block the lens with any object while the projector is running.
ENTERTAINMENT ENTERTAINMENT Using SCREEN SHARE * This feature is available for the PW800G model only. 1 Set the external input of the projector to SCREEN SHARE. 2 Enable related SCREEN SHARE function on the device you wish to connect. 3 Connect the Projector from the search list on the device you wish to connect. (When you connect the projector to your laptop, input the PIN code shown on your display. The request for a PIN will be shown only at the initial connection.
MY MEDIA MY MEDIA Removing a USB Device Before Using 1 Click the Q.MENU button. 2 Use the or button to move Connecting a USB Device 3 Select a USB to remove. Wait for Connect a USB device (external HDD, USB memory) to the USB port of projector to enjoy the content files stored in the USB device with your projector. You cannot write or delete data in the USB device. Connect a USB flash drive as shown below. USB Flash Drive 31 to USB Device and press the OK button.
MY MEDIA Tips for Using a USB Device yy If the USB storage device has a builtin auto recognition program or uses its own driver, it may not work. yy Some USB storage devices may not work or may work incorrectly. yy If you use a USB extension cable, the USB device may not be recognized or may not work properly. yy Use only USB storage devices formatted with the Windows FAT32 or NTFS file system.
MY MEDIA To Use My Media 1 Press the SETTINGS button on the remote control. 2 Select MY MEDIA. Select desired file from the list. Watch the chosen file. Sets play related settings by checking option during disk playback. My Media supporting file yy Maximum data transfer rate: 20 Mbps (Mega bit per second) yy External supported subtitle formats: *.smi, *.srt, *.sub (MicroDVD, SubViewer 1.0/2.0), *.ass, *.ssa, *.txt (TMPlayer), *.
MY MEDIA Video Supported Codec Maximum: 1920 x 1080 @ 30p (only Motion JPEG 640 x 480 @ 30p) Extension .asf, .wmv .divx, .avi .mp4, .m4v, .mov .mkv .ts, .trp, .tp, .mts, .m2ts .vob .mpg Codec Video VC-1 Advanced Profile, VC-1 Simple and Main Profiles Audio WMA Standard, WMA 9 Professional Video DivX3.11, DivX4, DivX5, DivX6, XVID, H.264/AVC Audio MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital Video H.264 / AVC, MPEG-4 Part 2 Audio AAC Video H.
MY MEDIA Audio File File type MP3 AC3 MPEG AAC, HEAAC CDDA LPCM Item Info Bit rate 32 kbps to 320 kbps Sampling rate 32 kHz to 48 kHz Bit rate 32 kbps to 640 kbps Sampling rate 32 kHz, 44.1 kHz, 48 kHz Bit rate 32 kbps to 448 kbps Sampling rate 32 kHz to 48 kHz Bit rate 24 kbps to 3844 kbps Sampling rate 8 kHz to 96 kHz Bit rate 1.44 kbps Sampling rate 44.1 kHz Bit rate 1.41 Mbps to 9.6 Mbps Sampling rate Multi-channel : 44.1 kHz, 88.2 kHz / 48 kHz, 96 kHz Stereo : 176.
MY MEDIA Watching the Videos In the Movie List, you can watch movies stored on the connected USB device. Controls playback and sets options while viewing videos. Tips for Playing Video Files yy Some subtitles created by users may not work properly. yy The video and subtitle files should be placed in the same folder. For subtitles to display correctly, the video and subtitle files must have the same name.
MY MEDIA 5 Browsing Movie List Play a video file stored in the connected device. 1 2 3 4 Control playback by using the following buttons. Connect a USB storage device. Press the USB button. Use the or button to select Movie List and press the OK button. Use the , , , or button to select the file you want and press the OK button. Page 1/1 Movie List USB STORAGE DEVICE book doc pic Page 1/1 Butterfly_...
MY MEDIA Options for Movie List 1 Press the Q.MENU button. 2 Use the or button to move to a desired option and press the OK button. 3 Use the , , up each item. , or Setting Subtitle Language button to set Set Video Play. Setting Picture Size Audio Language Description Selects the size of a playback screen. yy Full : Files are played in full screen mode according to the aspect ratio of video. y y Original : Displays the video in the original size.
MY MEDIA Subtitle Language Subtitle LanLanguage guage Latin1 English, Spanish, French, German, Italian, Swedish, Finnish, Dutch, Portuguese, Danish, Romanian, Norwegian, Albanian, Gaelic, Welsh, Irish, Catalan, Valencian Latin2 Bosnian, Polish, Croatian, Czech, Slovak, Slovenian, Serbian, Hungarian Latin4 Estonian, Latvian, Lithuanian Cyrillic Bulgarian, Macedonian, Russian, Ukranian, Kazakh Greek Greek Turkish Turkish Hebrew Modern Hebrew Chinese Simplified Chinese Korean Korean Arabic Arabic Thai Thai Se
MY MEDIA Registering the DivX code Checks DivX Reg. Code for replaying DivX protected videos. Register at http://vod.divx.com. Use Reg. Code to rent or purchase movies at www.divx.com/vod. 1 In the Settings menu, move to OPTION 1 and press DivX(R) VOD. To deregister the DivX code Use the DivX deregistration code to deactivate the DivX DRM function. 1 In the Settings menu, move to OPTION 1 and press DivX(R) VOD. 2 Use the or button to go to Deregistration and press the OK button.
MY MEDIA Viewing the Photos You can view photos stored on a connected device. Supported Photo Files PHOTO (*.JPEG) Baseline: 64-pixel (width) x 64-pixel (height) - 15360-pixel (width) x 8640-pixel (height) Progressive: 64-pixel (width) x 64-pixel (height) - 1920-pixel (width) x 1440-pixel (height) yy Only JPEG files are supported. yy Non-supported files are displayed in the form of an icon. yy An error message is displayed for corrupted files or file formats that cannot be played.
MY MEDIA 5 Control playback by using the following buttons. 01_a.jpg 2008/12/10 1920 x 1080 479 KB [1/4] Slideshow BGM Setting ꔦ Q.MENU Option Hide Exit Description Selects the previous or next photo. Slide- All photos are displayed show during slide show. yy Set Slide Speed in the Option → Set Photo View. menu. BGM You can listen to music while viewing photos in full size. yy Set BGM in the Option → Set Photo View. menu. Rotates photos. yy Rotates a photo 90°, 180°, 270°, or 360° clockwise.
MY MEDIA Options for Photo List 1 Press the Q.MENU button. 2 Use the or button to move to a desired option and press the OK button. 3 Use , , each item. , or button to set up Set Photo View. Setting Slide Speed BGM Description Selects a slideshow speed. Selects a music folder for the background music. yy You cannot change the music folder while the background music is playing. yy For background music, only the folder from the same device can be selected. -R epeat : Selects repeat play.
MY MEDIA Listening to Music You can play audio files stored on the connected device. Supported Music Files *.MP3 Bit rate range 32 Kbps to 320 Kbps yy Sampling rate MPEG1 Layer3: 32 kHz, 44.1 kHz, 48 kHz yy Sampling rate MPEG2 Layer3: 16 kHz, 22.05 kHz, 24 kHz Browsing Music List 1 Connect a USB storage device. 2 Press the USB button. 3 Use the or button to select Music List and press the OK button. 4 Use the , , , or button to select the file you want and press the OK button.
MY MEDIA 5 Control playback by using the Options for Music List following buttons. Page 1/1 Music List USB STORAGE DEVICE Drive1 ꘧ Page Change Page 1/1 Butterfly_... 03:25 1 Press the Q.MENU button. 2 Use the or button to move to a desired option and press the OK button. 3 Use , , each item. 002. - B02.mp3 � �� Q.MENU Setting 02:30 / 03:25 Option Hide 45 Exit Description Changes the playing position. Stops playing. Returns to normal playback. Pauses the media player.
MY MEDIA Viewing Files You can see document files stored on a connected device. Supported File Formats XLS, XLSX, DOC, DOCX, PPT, PPTX, TXT, PDF, HWP Microsoft Office 97/2000/2002/2003/2007 version Adobe PDF 1.0/1.1/1.2/1.3/ 1.4 version Hangul: 97/2000/2002/2005/2007 version yy File Viewer realigns a document, so it may look different from what is displayed on a PC. yy For documents that include images, the resolution may look lower during the realigning process.
MY MEDIA 5 Control playback by using the Options for File List following buttons. yy Click Go Page then the pop-up window for selecting the number of page appears. Input the page to move to the page you want. yy Press the VOLUME +, - button to zoom in or zoom out. Press the OK button and then use the Up/Down/Left/Right buttons to move to Go Page or Zoom. Go Page ꔦ Zoom Q.MENU Option Hide 47 Exit Setting Description Go Moves to the page you want.
3D FUNCTION 3D FUNCTION 3D technology uses different video frames for each eye to add depth to the video. While Watching 3D WARNING yy If you view 3D video or images too closely for a long period of time, your eyesight may become worse. yy If you watch the projector or game screen for a long time with 3D glasses on, you may experience dizziness or eye fatigue. yy People with chronic diseases (epilepsy, cardiovascular disease, blood pressure-related diseases, etc.
3D FUNCTION yy Warning about photosensitivity seizures - Some users may experience a seizure or other abnormal symptoms when they are exposed to a flashing light or particular patterns from a video game. If anyone in your family has a history of epilepsy or has ever experienced any kind of seizure, please consult your doctor before viewing 3D images. If you experience one of the following symptoms while watching a 3D video, stop watching the 3D video immediately and take a rest.
3D FUNCTION yy You may see left and right images overlapped during projector initialization after it is powered on. It may take some time for optimization. yy It may take some time for the 3D image to look normal after you turn your eyes away from the screen and look back at the 3D image. yy It may flicker slightly while watching 3D images under a 3 wavelength lamp fluorescent light (50 Hz to 60 Hz) or near windows. If so, it is recommended to block the sun light with a curtain and to dim the lights.
3D FUNCTION 51 Requirements for Watching 3D Images * Optimum viewing angle: Top/Bottom/Left/Right 9° Recommended viewing distance: 3 m to 5 m Recommended screen size: 101 cm * Watching 3D videos should be done in dark room environments only. NOTE yy The pairing with the DLP-LINK glasses is affected by the intensity of light reflected from the screen.
3D FUNCTION 1 Please check the minimum system requirements for your computer. Minimum requirements are as follows: Microsoft® Windows® XP, Vista 32/64 bit ,Windows 7 32/64 bit Intel® Core 2 Duo or AMD Athlon™ X2 CPU or higher More than 1 GB of system memory (2 GB recommended) Free space of 100 MB or more DirectX 9 or higher Video card should support 120 vertical frequency (Hz).
3D FUNCTION 53 To Use DLP-LINK (DLP-Ready) Type Glasses 1 While watching 3D images from the projector, press buttons on the glasses. 2 When you press the button, the glasses flicker to be synchronized with the 3D images. (The flickering is a unique operation method of DLP-LINK type glasses. It may be different depending on the glasses type.) 3 If the glasses flicker or problems occur while watching 3D, first turn the lights off to make the room darker.
CUSTOMIZING SETTINGS CUSTOMIZING SETTINGS SETTINGS * The illustration of the menu may differ from the actual screen on the product. The illustration of Settings is from the PW800G model. 1 Press the SETTINGS button. 2 Use the , , , or button to select the desired item and press the OK button. 3 Use the , , , or button to set up the desired item and press the OK button. 4 Press the EXIT button when completed. Menu Description PICTURE Adjusts the image quality for optimal viewing.
CUSTOMIZING SETTINGS PICTURE Settings 1 Press the SETTINGS button. 2 Use the , , , or button to select PICTURE PICTURE and press the OK button. 3 Use the , , , or button to set up the desired item and press the OK button. - To return to the previous menu, press the button. 4 Press the EXIT button when completed.
CUSTOMIZING SETTINGS Item Description Brightness Adjusts the overall screen brightness. Sharpness Adjusts the sharpness of the borders between bright and dark. Horizontal and Vertical Sharpness are available only in Expert1/2. Color Adjusts the intensity of all colors. Tint Adjusts the balance between red and green levels. Advanced Customizes the advanced settings. Control Picture Sets optional settings. Option Picture Resets values customized by the user. Reset Each picture mode is reset.
CUSTOMIZING SETTINGS 57 Advanced Control Item Dynamic Contrast Dynamic Color Color Gamut Description Adjusts contrast and colour to the optimal level according to the screen’s brightness. Adjusts colours for more natural-looking colours. Selects the range of colours that can be expressed. yy Standard: Displays the original colors of an input signal regardless of the display features. yy Wide: Makes use of the display's rich colors.
CUSTOMIZING SETTINGS Item Description Color In Expert mode, you can customize the options of each mode. Temperature Gamma: Select 1.9, 2.2, or 2.4. a. Method: 2 Points - Pattern: Inner, Outer - Points: Low, High -R ed/Green/Blue: Adjustable range -50 to +50. - Apply to all inputs: T he values of the Color Temperature is applied to all the input modes. b.
CUSTOMIZING SETTINGS 59 Picture Option Item Description Noise Reduction Reduces screen noise in the video. MPEG Noise Reduction Eliminates noise generated while creating digital picture signals. Black Level Adjusts the brightness or darkness of the screen to suit the black level of the picture input using the degree of darkness (black level) of the screen. Real Cinema Optimizes the screen for movie viewing. Color Temperature Adjusts the overall color of the screen to suit your preference.
CUSTOMIZING SETTINGS AUDIO Settings 1 Press the SETTINGS button. 2 Use the , , , or button to select AUDIO and press the OK button. 3 Use the , , , or button to set up the desired item and press the OK button. - To return to the previous menu, press the button. AUDIO yySound Mode ꔂ Move ꔉ OK : Standard yySound Effect yyAuto Volume : Off 4 Press the EXIT button when completed. The available audio settings are described as follows.
CUSTOMIZING SETTINGS 61 TIME Settings 1 Press the SETTINGS button. 2 Use the , , , or button to select TIME and press the OK button. 3 Use the , , , or button to set up the desired item and press the OK button. - To return to the previous menu, press the button. TIME ꔂ Move ꔉ OK yySleep Timer : Off yyAuto Off : 60 min. yyAutomatic Standby : Off 4 Press the EXIT button when completed. The available time settings are described as follows.
CUSTOMIZING SETTINGS WIRELESS Settings * Available for the PW800G model only. 1 Press the SETTINGS button. 2 Use the , , , or button to select WIRELESS yySCREEN SHARE WIRELESS and press the OK button. ꔂ Move ꔉ OK : [PJTR][LG]PW800[0000] yyGroup 3 Use the , , , or button to set up the desired item and press the OK button. - To return to the previous menu, press the button. yyChannel 4 Press the EXIT button when completed. The available wireless settings are described as follows.
CUSTOMIZING SETTINGS 63 INFORMATION * Available for the PW600G model only. 1 Press the SETTINGS button. 2 Use the , , , or button to select ? INFORMATION INFORMATION and press the OK button. ? The following are INFORMATION-related items. Item Model Name INPUT Description Shows the model name of the product. Shows the current status of inputs.
CUSTOMIZING SETTINGS OPTION 1 Settings 1 Press the SETTINGS button. 2 Use the , , , or button to select OPTION 1 ꔂ Move ꔉ OK yyLanguage OPTION 1 and press the OK button. yy3D Mode 3 Use the yyAuto Input Search : Off , , , or button to set up the desired item and press the OK button. - To return to the previous menu, press the button. yyDivX(R) VOD yyInitial Setting yyMode Setting : Standard 4 Press the EXIT button when completed. The available option 1 settings are described as follows.
CUSTOMIZING SETTINGS OPTION 2 Settings 1 Press the SETTINGS button. 2 Use the , , , or button to select OPTION 2 ꔂ Move ꔉ OK yyKeystone OPTION 2 and press the OK button. 3 Use the , , , or button to set up the desired item and press the OK button. - To return to the previous menu, press the button. 0 yyAuto Keystone : On yyPJT Mode : Front yyHigh Altitude : Off yyBlank Image : Blue yyAuto Power : Off - + yySelf Diagnosis 4 Press the EXIT button when completed.
CUSTOMIZING SETTINGS Item Auto Power Description Makes the projector turn on automatically when the adaptor plug is inserted. Item On Off Self Diagnosis When the AC/DC plug is connected to the projector, it turns on automatically. When the AC/DC plug is connected to the projector, it goes into standby mode. Troubleshoots functional problems that can arise while using the product.
CONNECTING DEVICES 67 CONNECTING DEVICES You can connect various external devices to the projector.
CONNECTING DEVICES Connecting to HD Receiver, DVD, VCR Player, or External Devices Connect an HD receiver, DVD, VCR player, or External Devices to the projector and select an appropriate input mode. HDMI to DVI Connection Using an HDMI to DVI cable, connect the projector's port to the DVI OUT port. To output audio, use an audio cable for connection. Press the INPUT button on the remote control to select HDMI. HDMI Connection With an HDMI cable, you can enjoy high quality picture and sound.
CONNECTING DEVICES 69 AV Connection Component Connection Connect the output ports of an external device and the AV IN ports of the projector using an AV cable. Press the INPUT button on the remote control to select AV. Check whether cables of the same color are connected properly. You can enjoy a video by connecting the Component port of an external device to the RGB IN port of the projector. Press the INPUT button on the remote control to select Component.
CONNECTING DEVICES Connecting a PC The projector supports Plug & Play. Your PC will automatically detect the projector and requires no driver installation. HDMI Connection Using an HDMI cable, connect the port of the projector to the HDMI output port of your PC. Both video and audio are output at the same time. Press the INPUT button on the remote control to select HDMI. HDMI to DVI Connection Using an HDMI to DVI cable, connect the projector's port to the DVI OUT port.
CONNECTING DEVICES 71 RGB Connection Connect the PC output and the PC video input port of the projector with the RGB cable. For audio signal, connect the PC and the projector with an optional audio cable. Press the INPUT button on the remote control to select RGB-PC.
CONNECTING DEVICES Connecting a Laptop You can connect the projector to a laptop to use various functions. HDMI Connection Using an HDMI cable, connect the port of the projector to the HDMI output port of your laptop. Both video and audio are output at the same time. Press the INPUT button on the remote control to select HDMI. The table below shows examples of switching the output.
CONNECTING DEVICES Connecting to Headphones You can listen to the audio through a headphone.
CONNECTING DEVICES Using the Mirroring Function of a Mobile Phone MHL/Slimport Connection You must use a HDMI adapter to connect your cell phone to the projector and to output images and sound from your cell phone to the projector. The compatible HDMI adapters are different, depending upon your cell phone type. Therefore, purchase an appropriate MHL or Slimport adapter. (To find out whether your device is MHL/Slimport-certified, please contact your device manufacturer.
MAINTENANCE MAINTENANCE Clean your projector to keep it in optimal condition. Cleaning Cleaning the Lens If there is any dust or staining on the lens surface, you must clean the lens. Use an air spray or a cleaning cloth to clean the lens. To remove dust or stains, use an air spray or apply a small amount of cleaning agent onto a swab or soft cloth to lightly rub the lens. Please be aware that liquid may flow into the lens if the product is sprayed directly onto the lens.
SPECIFICATIONS SPECIFICATIONS MODELS Resolution (Pixel) Aspect ratio Panel size (mm) Projection distance (Video size) Ratio of upward projection Working range of the remote control Video input AC-DC Adaptor Audio Output Height (mm) Width (mm) Depth (mm) Weight ( ) USB Device Power Operation environment PW600G (PW600G-GL) / PW800G (PW800G-GL) 1280 (Horizontal) × 800 (Vertical) 16:10 (Horizontal:Vertical) 11.623 0.80 m to 3.25 m (63.5 cm to 254.
SPECIFICATIONS 77 Supported RGB-PC/HDMI(PC) Mode Supported HDMI/DVI-DTV Mode Horizontal Resolution Frequency (kHz) Horizontal Vertical Resolution Frequency Frequency (kHz) (Hz) Vertical Frequency (Hz) 640 x 350 31.468 70.09 720 x 400 31.469 70.08 640 x 480 31.469 59.94 800 x 600 37.879 60.31 1024 x 768 48.363 97.551 60.00 120 1152 x 864 54.348 60.053 1280 x 800 49.68 60 1360 x 768 47.712 60.015 1280 x 1024 63.981 60.02 1400 x 1050 65.317 59.979 1680 x 1050 65.
SPECIFICATIONS Open Source Software Notice Information To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
The model and serial number of the projector are located on the back or on the side of the projector. Record them below should you ever need service.