Installation Guide

ManualsBrandsLG Electronics ManualsSmart AppliancesStyler Steam Clothing Care System

12 INSTALLATION

INSTALLATION

INSTALLATION OVERVIEW

Please read the following installation instructions first after

purchasing this product or transporting it to another location.

PRODUCT SPECIFICATIONS

The appearance and specifications listed in this manual may vary due to constant product improvements.

steam clothing care S3RERB

description

electric machine for maintaining clothing

electrical requirements

please refer to the rating label regarding detailed information

dimensions

17 ½ in. (W) X 23 in. (D) X 72

in. (H), 39 ¾ in. (D with door

open)

445 mm (W) X 585 mm (D) X 1850 mm (H), 1010 mm (D with

door open)

net weight

183 lb (83 kg)

maximum capacity

4 items

power consumption

1500 W

safety device

double overheating safety device, thermal fuse, programming

Check and choose the

proper location

Level the Styler

Reverse the door swing

(if needed)

Connect to grounded outlet

100–130V only

in.

20cm over

2 in.

5cm over

2 in.

5cm over

Unpack and remove

shipping material

Install carpet spikes

(if needed)

Remove material from

inside and outside of cabinet

Summary of content (7 pages)

PAGE 1
2 INSTALLATION INSTALLATION INSTALLATION OVERVIEW Please read the following installation instructions first after purchasing this product or transporting it to another location. 7 3/4 in. 20cm ov er 2 in. 5cm over 2 in.
PAGE 2
INSTALLATION 13 UNPACKING THE Styler Remove tape and any temporary labels from the Styler before using. Do not remove any warning labels, the model and serial number label, or the Tech Sheet that is located under the front of the Styler. • To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
PAGE 3
14 INSTALLATION INSTALLATION LOCATION REQUIREMENTS Warning Read all installation instructions completely before installing and operating the Styler. It is important to review this entire manual before installing and using the Styler. The installation requires: yy A grounded electrical outlet located within 2 ft. (61 cm) of either side of the appliance. yy A sturdy floor to support the total appliance weight of 183 lbs (83 kg). The combined weight of any other laundry appliances should also be considered.
PAGE 4
INSTALLATION 15 Installation Spacing for Special Cases The following clearances are recommended for the Styler. Although the Styler has been tested for clearances of 13/16 inch (3 cm) on the sides and rear, recommended clearances should be considered for the following reasons: Installing the Styler in an area with restricted clearance and/or ventilation could result in reduced performance or product damage. yy Additional space should be considered for ease of installation and servicing.
PAGE 5
16 INSTALLATION leveling the styler Warning Warning yyThe Styler is heavy. Use two or more people if installing the rear leveling feet. Failure to do so can result in back injury or other injury. yyKeep the Styler upright when moving and installing it. If you lay the Styler on its side, refrigerant may leak and cause the appliance to malfunction. yy To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses.
PAGE 6
INSTALLATION 17 Reversing the Door 5 Warning If the carpet has very deep pile or padding, the front feet may need to be extended slightly to install the drip tray. Warning Do not attempt to reverse the door swing yourself. If the direction of the door swing needs to be changed after installation, contact the LG Customer Information Center at 1-800-243-0000 (USA) or 1-888-542-2623 (Canada). installing on carpeting If installing the Styler on carpeting, follow these instructions.
PAGE 7
18 INSTALLATION 3 Place the adhesive side of the non-skid pad on the floor. ASSEMBLING the DRIP Tray Before using the Styler, insert the drip tray onto the bottom of the cabinet. This side up Adhesive side B Remove backing 1 Hold the tray so the arrow and letter on the front of the tray face up. 2 Insert one side of the tray first, then the other. Push the tray until it slides completely in. 4 Recheck the Styler's levelness.