LG-SD500 Operator’ s Guide December 08, 1999 jong-gil Lee
FCC RF EXPOSURE INFORMATION WARNING! Read this information before using your phone In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies.
LGIC Call Status Functions 1. Memo (Memo Soft Key 2) * Function to store a telephone number while calling l Select Memo and enter the telephone number to store. l Press Store (Soft Key 1) key. (Name is not stored) 2. Record While Calling (Menu Soft Key 1 + 1) * Function to record the conversation while calling 3. Send Own No.
LGIC Stand-by Status Menu Set-up and Its Functions PIM 1. PHONE BOOK (Cion Secretary) [Menu + 1] * Telephone Directory / Scheduler / Alarm / Call Reserve / World Time 1.1 Contact Secretary [Menu + 1 + 1 ] 1.1.1 NEW ENTRY (Telephone Directory Register) [Menu + 1 + 1 + 1 ] 1.1.2 FIND ENTRY (Telephone Directory Search) [Menu + 1 + 1 + 2 ] 1.1.3 DELETE ENTRY (Telephone Directory Delete) [Menu + 1 + 1 + 3 ] - 1.2 - See the manual on the telephone directory function.
LGIC l ‘ AM’ and ‘ PM’ mode can be switched with Soft Key1[AM/PM] l You can edit the entered contents using DEL key. l Press OK key to store the entered alarm time. Note: The alarm bell is triggered at the set alarm time with the message of “ Alarming Now” displayed on the display. Note: In case ‘ Once’ is selected, if the END key is pressed or 1minute is passed, the alarm time is deleted. 1.
LGIC 2. Volume Control [Menu + 2] * Function to control Ring / Key Tone / Call Volume 2.1 Ringer Volume (Receiver Volume Control) [Menu +2 +1] l Select the volume using the next setup key (Soft Key 1). l Select the volume you want using V/# keys. l Store the selected volume using the selection key. 2.2 Key Tone Volume Control [Menu +2 +2] l Select the volume using the next setup key (Soft Key 1). l Select the volume you want using V/# key. l Store the selected volume using the selection key.
LGIC 4. Call Time [Menu + 4] * Function to verify the record on the call time 4.1 Last Call Time * Function to show the last call time l Select Menu + 4 + 1. l Press OK key to return to the stand-by state. 4.2 Total Call Time * Function to show the number of call and the call time for all calls of receiving and transmitting. User can verify the total number of calls made and the call time through this function. l Select Menu + 4 + 2.
LGIC locking on the [Select] key is released and the [Locking Release] button is changed to [Select] button. l - Even in this case, whenever you try to call, the password is required. - If you want the locking release, you should release this setup from the [Menu]. If you select ‘ Power-On’ , the locking function is not immediately executed but when the phone is switched on, it is automatically set to the lock mode and at the same time, the soft key is changed to [Menu], [Locking Release].
LGIC ‘ None’ appears. l Select the memory address where you want to make input using the next setup key (Soft Key1) or ‘ V/#’ key [ 1 ~ 3 ] l Select the edit mode by pressing EDIT key. l Enter the telephone to store and press OK key. If you want to terminate the process at this time, press the END key and if you want to enter the telephone in other memory address, repeat the procedures that follow the step of memory address selection. 5.6.
LGIC 6. Convenient Functions [ Menu + 6 ] * Area code input/setup, automatic reception, calculator, voice recognition setup, automatic answer functions can be set. 6.1 Automatic Area Code * The stored area code is added to the dial number automatically while a call is originated. l Select Menu + 6 + 1. l Select one of ‘ Setup/Release’ using the next setup key (Soft Key1) or ‘ V/#’ key and press STORE key. l If you select ‘ Release’ , it will be in the stand-by state.
LGIC l Select [ = ] operator using Soft key1 key and press [OK] key. [9 digits including the decimal point can be displayed] If you want to make other operation on the operation result onward, press other operator than [ = ] and press STORE key to make continuous operation. If the operation result exceeds 9 digits including the decimal point, error message appears and it returns to the initial status of the calculator. 6.
LGIC l Select Menu + 7 + 1 l Select one of ‘ Always Off / Flip Open / 10 Sec. / Auto’ using the next setup (Soft Key1) or ‘ V/#’ key. l Press OK to store the selected value. Following values can be set. Always Off: Background illumination is always off. 10 Sec.: Background illumination is on for 10 seconds. Automatic: It remains in off-state from 08:00 through 17:00, otherwise the background illumination lights up every 9 seconds.
LGIC Modem Communication: You select this mode when you receive the counterpart’ s call in the 1 : 1 data communication mode. Fax Communication: You select this mode when you receive a fax from your counterpart. 8. Audible Alert Setup [Menu + 8] * Three types of audible alert are provided. 8.1 Call Connect Alert * An alert to notify of the state of the call connection while a call is originated.
LGIC l Select ‘ Menu + 0 + 000000 + 1’ l Select one of NAM#1 ~ NAM#4 using the next setup key (Soft Key1) or ‘ V/#’ key and press STORE key. As NAM#1 ~ NAM#4 have different NAM parameters respectively, if you select the NAM that is not identified with the subscribed number, the service is not provided. 9.2 AUTO NAM Setup [Menu + 0 + 000000 + 2] It is the function to automatically set the NAM that is identified with the subscribed number when more than one NAM are used.
LGIC 9.3.3 Error Delete [Menu + 0 + 000000 + 3 + 3] * Function used to delete the entities stored in the error list. l Select ‘ Menu + 0 + 000000 + 3 + 3’ . l Select ‘ Yes’ of ‘ Yes/No’ using the next setup key (Soft Key1) or ‘ V/#’ key and press STORE key. At this moment, a message of “ Please, wait” appears and once the deletion is completed, it returns to the previous status. 9.3.4 Error List [Menu + 0 + 000000 + 3 + 4] * Function used to verify the entities stored in the error list.
LGIC Using Search Menu 1. Latest Call List [Search + 1] * Used to verify the list of 10 telephone numbers that were connected lately. l Select ‘ Search + 1’ [Latest call list appears] Call => Originating End => It returns to the stand-by status Del => It returns to Stand-by status/Previous status View => It returns to detailed information display status [Function of Keys of Detailed Information Display] Call => Originating.
LGIC 5. Own Number Search [Search + 5] * Function to verify her/his phone number. l Select ‘ Search + 5’ Other Function Keys 1. Message Key - If you press this key in the step of telephone number edit, you can enter ‘ manual standby/time stand-by/hyphen’ . 2. # Key - If you press this key on hold for a specific time at any state, you can make a call with onetouch.
LGIC Annex 2 : Voice Recognition Function 1. Using Voice Recognition Function * For using the voice recognition dialing function, there should be a voice available that was previously stored in the memory through the voice learning process. And the voice recognition function should be set through ‘ Menu 6 + 5’ 1) Voice Learning l This function is performed following the procedures for the conventional telephone number storing.
LGIC “ Your name, please“ Enter your name in voice “ Your name again, please “ Enter your name in voice again “ If the data you have input so far are correct, select ‘ Yes’ , otherwise, select ‘ No’ Correct? (If the data you have input so far are correct, select ‘ Yes’ , otherwise, select ‘ No’ ) 2) Voice Dialing l This function is performed in the idle state by pressing DEL key and its procedures are as follows.
LGIC Annex3: Automatic Answer Function 1. What is Automatic Answer Function? It is a function to store the conversation message of the counterpart through the automatic answering by the terminal when there is a call. 2. Operation Concept (1) Once the automatic answering function has been set, a message of ‘ Auto Answering… : (’ is displayed on the LCD display.
LGIC - As a function to set the automatic answering mode, it can be set to “ Setup/Release” mode and its default is “ Release” . (2) Message Retrieve (Menu 6 + 6 + 2) - You can retrieve the recorded message of your counterpart while calling. (3) Message Delete (Menu 6 + 6 + 3) - Function to delete the recorded message. (4) Message Select (Menu 6 + 6 + 4) - You can select ‘ Basic message/Recorded message’ to release in the automatic answering mode and its default is the basic message.
LGIC Hold-on Function 1. What is Hold-on function? It is also called “ Reception Hold Message Transmission Function” . If there is a call while you are occupied with some urgent matters, you can release the message of [Sorry but hold on, please and I get back to you shortly… (up to 30 seconds)] and converse with your counterpart shortly. 2. How to Use 1) Message Delivery upon a Call (1) Select “ Setup” from Menu 6 + 8 + 2.
