ENGLISH OWNER’S MANUAL LCD TOUCH MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD TOUCH MONITOR MODELS T1710BP T1910BP www.lg.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur.
Proper posture The proper posture for using the product when seated Adjust the screen so that you can comfortably look at it at a slight downward angle from your natural eye level. Take a break for approximately 10 minutes every hour to reduce any fatigue caused by long-time usage. The stand of the touch monitor allows the product to be used in the optimum position. Adjust the stand angle between 15 to 30 degrees to create the optimum user environment.
Proper posture The proper posture for using the product when standing Adjust the screen so that you can comfortably look at it at a slight downward angle from your natural eye level. Take a break for approximately 10 minutes every hour to reduce any fatigue caused by long-time usage. The stand of the touch monitor allows the product to be used in the optimum position. Adjust the stand angle between 45 to 66(68) degrees to create the optimum user environment. Gaze downward toward the center of the monitor.
Accessories !!! Thank you for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Owner's Manual CD / Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) USB Cable NOTE This accessories may look different from those shown here.
Basic Adjustments of the Stand After installing the monitor, adjust the angle as follows. Basic Adjustment 1. Adjust the angle of the panel as follows. How to adjust the angle of the panel Tilt Range : T1710BP : 15˚ to 66˚ T1910BP : 15˚ to 68˚ 15˚ 66˚(68˚) Push back the panel to the end, and use from the point that it automatically returns. Panel Stand Do not push the stand with basic adjustment to the direction of the panel.
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . A Connect D-sub Cable (PC) B Connect D-sub Cable (Mac) NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown.
Connecting the Display To Use Touch Screen 1) Connect the USB cable for the touch screen as shown below. 2) Execute the touch screen calibration. 3) Set "Double Click" function. 4) For details, refer to the touch screen user's manual. * LG Touch Screen Monitor supports the following Microsoft Windows operating systems: Windows XP, Windows VISTA(32bit, 64bit), Windows 7(32bit, 64bit) NOTE When you lose user's manual CD or want to update the program, please refer to http://www.lg.com.
Control Panel Functions Front Panel Controls Control MENU Button Function Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds.
Control Panel Functions Control Function Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page A18. AUTO/SET Button Use this button to select an icon in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button prior to entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. (D-sub ) NOTE The order of icons may differ depending on the model (A13 to A18 ).
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display blackish images.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING MENU : Exit : Decrease : Increase SET : Select another sub-menu HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description LANGUAGE To choose the language in which the control names are displayed. OSD POSITION To adjust position of the OSD window on the screen. WHITE BALANCE If the output of the video card is different from the required specifications, the color level may deteriorate due to video signal distortion.
On Screen Display(OSD) Selection and Adjustment Select the button at the bottom of the monitor, then the OSD screen will appear. Menu Name Icons Sub-menu Name Main menu Sub menu Description This feature lets you easily select the best desired image condition optimized to the environment (ambient illumination, image types etc). MOVIE: For animation images in videos or movies INTERNET: For text images (Word processing etc.) USER The user can directly adjust ACE and RCM.
Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? ● Is the power indicator light on? • Press the Power button. ● Is the power on and the • Adjust the brightness and the contrast.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (Color Quality) at Control Panel --> Settings. ● The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution.
Specifications T1710BP Display 43.27 cm (17.0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size: 43.27 cm 0.264 mm x 0.264 mm (Pixel Pitch) Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Input Form 30 kHz to 83 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate TTL SOG (Sync On Green) 15 pin D-sub Connector RGB Analog (0.
Specifications T1910BP Display 48.19 cm (19.0 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size: 48.19 cm 0.294 mm x 0.294 mm (Pixel Pitch) Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Input Form 30 kHz to 83 kHz (Automatic) 56 Hz to 75 Hz (Automatic) Separate TTL SOG (Sync On Green) 15 pin D-sub Connector RGB Analog (0.
Specifications Preset Modes (Resolution) Display Modes (Resolution) 1 2 3 4 5 6 7 8 9 10 11 *12 13 Horizontal Freq. (kHz) 31.469 31.468 31.469 37.500 37.879 46.875 49.725 48.363 60.123 68.681 61.805 63.981 79.976 640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1152 x 870 1152 x 900 1280 x 1024 1280 x 1024 Vertical Freq.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. Place the monitor with its front facing downward on a soft cloth. 2. Separate the head and the stand with the use of a screwdriver.
Installing the Wall mount plate 3. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased. Wall Mount pad Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores.
Make sure to read the Important Precautions before using the product. Keep the User’s Guide(CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.
