User’s Guide W2363V Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur.
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards Power Cord (Depending on the country) DVI-D Signal Cable (This feature is not available in all countries.) 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) IMPORTANT This accessories may look different from those shown here.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting and Disassembling the stand 1. Place the monitor face down on the soft cloth. 2. Assemble the Stand Base into the Stand Body in the correct direction. Make sure you push the Stand Base until the end. Stand Body Stand Base The Stand Base may fall and get damaged or cause injury.
Connecting the Display 3. Turn the screw to the right to fix the Stand Body to the Stand Base. Screw Turn the screw by using the screw handle. 4. Then fold the screw handle flat. 5. Once assembled take the monitor up carefully and face the front side. 6. To disconnect the Stand Base from the Stand Body, unfold the screw handle and turn it to the left. IMPORTANT This picture depicts the general model of connection. Your monitor may differ from the items shown in the picture.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~15˚ 15 -5 Do not touch or press the screen when adjusting the angle of the monitor.
Connecting the Display Connecting with the PC/AV equipment 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable 1 and power cord 2 in order, then tighten the screw of the signal cable. A Connect DVI-D (Digital signal) Cable B Connect D-sub (Analog signal) Cable C Connect VIDEO and AUDIO Cable D Connect HDMI Cable (HDMI1, HDMI2) NOTE This is a simplified representation of the rear view.
Connecting the Display 3. Press the Power Button ( ) on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically. (Only Analog Mode) NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings. When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.
Control Panel Functions Front Panel Controls Button Use this button to enter THRU MODE, SRS TRUSURROUND HD, ARC or AUTO BRIGHT menus. For more information, refer to page 14 ~ 15. SOURCE Button When two or more input signals are connected, first monitor automatically detects one signal as main input, then you can select the input signal (DSUB/DVI/HDMI1/ HDMI2/COMPONENT) you want. INPUT MENU Button Use this button to enter or exit the On Screen Display.
Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. Use this button you can directly use PIP function. You can use PIP menu to select PIP input. For more information, refer to page 21. When two input signals are connected, one is main input, the other is PIP input. You can use this button to exchange the main input and PIP input. AUTO/SET Button Use this button to enter a selection in the On Screen Display.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the the monitor. Menu Name G-MODE MENU : Save & Exit , : Move Icons Sub-menu Name Main menu THRU MODE ON THRU MODE Sub menu THRU MODE G-MODE ON button on the front of Description ON Not use the Frame-Buffer memory to prevent the picture delay. It can use in GAME MODE to prevent picture delay. OFF Using the Frame-Buffer memory to control PIP, ARC function.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu ARC G-MODE ARC FULL Description 1:1 The picture will be displayed depends on Input resolution.No Scaling. If 640x480 resolution input, the picture will just display 640x480 size even though the 1920x1080 size panel. ORIGINAL The picture will be displayed with input resolution ratio scaling. If 640x480 resolution input, the picture will keep at 4:3 ratio scaling. FULL The picture will be displayed with Full size.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE DVI, DSUB input BRIGHTNESS To adjust the brightness of the screen. HDMI, COMPONENT input CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value: -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display blackish images. BLACK LEVEL You can set the offset level.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description COLOR DVI, DSUB input PRESET • sRGB: Set the screen color to fit the sRGB standard color specification. • 6500K: Slightly reddish white. • 9300K: Slightly bluish white. RED Set your own red color levels. GREEN Set your own green color levels. BLUE Set your own blue color levels. HUE Set your own HUE levels. SATURATION Set your own saturation levels.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING DSUB input HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description SETUP LANGUAGE To choose the language in which the control names are displayed. VOLUME LIGHTING LEVEL 3 OSD POSITION To adjust position of the OSD window on the screen. RTC If you set ON, you enable the Response Time Control function. If you set OFF, you disable the Response Time Control function. VOLUME To adjust the volume of headphone/Earphone.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PIP PIP ON/OFF PIP ON/OFF ON PIP INPUT DVI * It supports only for HDMI input in RGB (D-sub analog signal) mode. * The combinations of main screen and sub-screen (PIP) available are as shown below: PIP POSI TION PIP SOUND OFF To select PIP on or off.
Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? ● Is the power indicator light on? • Press the Power button. ● Is the power indicator blinking? • If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. ● The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution.
Specifications Display 23.0 inches (58.4 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size: 58.4 cm 0.265 x 0.265 mm (Pixel Pitch) Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) 19 pin HDMI Connector Analog (0.
Specifications Preset Modes (Resolution) DSUB/DVI Timing Display Modes (Resolution) Horizontal Freq. (kHz) 640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1680 x 1050 1920 x 1080 31.469 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.981 79.976 64.674 65.290 67.500 1 2 3 4 5 6 7 8 9 10 11 12 13 *14 Vertical Freq.
Specifications Preset Modes (Resolution) Component Video Timing Display Modes (Resolution) 1 2 3 4 5 6 7 8 480i 576i 480P 576P 720P 720P 1080i 1080i Horizontal Freq. (kHz) Vertical Freq. (Hz) 15.75 15.62 31.50 31.25 37.50 45.00 28.12 33.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. Place the monitor face down on the soft cloth. 2. To disconnect the Stand Base from the Stand Body, unfold the screw handle and turn it to the left. 3. Pull out the Stand Base to remove.
Installing the Wall mount plate 4. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores.
Digitally yours
