User’s Guide W2443S W2443T Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation.
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur.
Connecting the Display Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the stand base into stand body in the correct direction as shown in the picture, then tighten the screw which is attached to the stand base. Stand Body Stand Base Screw 3. Once assembled take the monitor up carefully and face the front side. Disassembling the stand 1. Place the monitor face down on the cushion or soft cloth. 2.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~15˚ 15 -5 Do not touch or press the screen when adjusting the angle of the monitor.
Connecting the Display W2443T Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. and power cord of the signal cable. A Connect DVI-D(Digital signal) Cable B Connect D-sub(Analog signal) Cable 2. Connect signal input cable 1 2 in order, then tighten the screw NOTE This is a simplified representation of the rear view.
Connecting the Display W2443S Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. and power cord of the signal cable. 2. Connect signal input cable 1 2 in order, then tighten the screw A Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown.
Control Panel Functions Front Panel Controls W2443T 1 2 3 4 5 2 3 4 5 W2443S 1 Button MENU Button Use this button to enter 4:3 IN WIDE, PHOTO EFFECT menus. For more information, refer to page 12. Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear.
Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. Use this function to select optimal image conditions in accordance with the surrounding environment (Brightness, Image type). For more information, refer to page 13. (SOURCE Hot key) When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. When only one signal is connected, it is automatically detected. The default setting is D-Sub.
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the of the monitor. button on the front MENU : Exit : Move SET : Select Main menu 4:3 IN WIDE Description To select the image size of the screen. WIDE • WIDE • 4:3 PHOTO EFFECT 4:3 : Switch to full screen mode according to input image signal. : Change the input image signal ratio to 4:3. To select the color effects of the screen. • NORMAL The PhotoEffect function is disabled.
On Screen Display(OSD) Selection and Adjustment The following OSD screen will appear when you press the button on the front of the monitor.This feature lets you easily select the best desired image condition optimized to the environment (ambient illumination, image types etc). Menu Name Icons MENU : Save & Exit , : Move Sub-menu Name F-ENGINE Active state Inactive state When the F-ENGINE is executed, the screen is split to show the effects of the selected function.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50 / 0 / 50 On the monitor, high gamma values display whitish images and low gamma values display blackish images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR PRESET Select the screen color.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description SETUP W2443S LANGUAGE To choose the language in which the control names are displayed. OSD POSITION To adjust position of the OSD window on the screen. WHITE BALANCE If the output of the video card is different the required specifications, the color level may deteriorate due to video signal distortion.
Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? ● Is the power indicator light on? • Press the Power button. ● Is the power indicator flickering? • If the display is in power saving mode, try moving the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. ● The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution.
Specifications W2443T Display 23.6 inches (59.9 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 59.9 cm 0.266 x 0.266 mm (Pixel pitch) Sync Input Horizontal Freq. Vertical Freq. Input Form 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green), Digital Video Input Signal Input Input Form 15 pin D-Sub Connector DVI-D Connector (Digital) RGB Analog (0.
Specifications W2443S Display 23.6 inches (59.9 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 59.9 cm 0.266 x 0.266 mm (Pixel pitch) Sync Input Horizontal Freq. Vertical Freq. Input Form 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green) Video Input Signal Input Input Form 15 pin D-Sub Connector RGB Analog (0.
Specifications Preset Modes (Resolution) Display Modes (Resolution) 1 2 3 4 5 6 7 8 9 10 11 *12 Horizontal Freq. (kHz) Vertical Freq. (Hz) 31.468 31.469 37.500 37.879 46.875 48.363 60.123 67.500 63.981 79.976 65.290 67.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. Place the monitor face down on the cushion or soft cloth. 2. Loosen the screw which is attached to the stand base, then take off the stand base from stand body. Stand Base Stand Body Screw 3. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate.
Digitally yours