2 INSTALLATION INSTALLATION Installation Parts and Tools Parts not Provided Electrical cable Water supply tube Fittings for tube Coupler Teflon™ tape Air gap Wire nuts for 16-gauge wiring Hose clamp ⅞" UL approved strain relief Electrical tape Flat-blade screwdriver Phillips screwdriver Hole saw min.
INSTALLATION 13 Installation Overview Leveling the Dishwasher Preparing Electrical Wiring Securing the Dishwasher to Countertop Preparing Water Supply Connection Connecting the Drain Hose Preparing the Dishwasher Connecting Water Supply Removing Lower Cover Connecting Power Sliding the Dishwasher into Cabinet Final Check ENGLISH Preparing Cabinet Opening Product Dimensions Back view Side view 26 5/8 - 26 13 /16" (676 - 681 mm) 23 3/4" (603 mm) 24 5/8" (625 mm) 33 5 /16" (846 mm) 4 1/2" (1
14 INSTALLATION Preparing Cabinet Opening This dishwasher is designed to fit a standard dishwasher opening. An opening may be needed on both sides to route plumbing and electrical connections. WARNING ••Don't use existing holes unless they are in the target area. Otherwise, the water supply and drain hose may be damaged by being crushed or kinked.
INSTALLATION 15 Preparing Electrical Wiring this appliance with the correct voltage 1 Operate as shown in this manual and on the rating plate. 2 3 4 If an outlet and other power connector are used, it should be in an accessible location adjacent to and not behind the dishwasher and within 4 ft (1.2 m) of the dishwasher's side. The wiring must be grounded properly. If in doubt, have it checked by a qualified electrician. Do not connect any other appliance to the same outlet. Route the wiring.
16 INSTALLATION Preparing Dishwasher Removable Rear Plastic Shipping Brace The rear shipping brace can be removed if additional clearance is needed when installing the dishwasher under a low countertop. NOTE ••Do not pull or lift the dishwasher using the handle; doing so can damage the door and hinges. Open the door and grab the body frame and the top front opening of the tub to move or lift the dishwasher. Removing Lower Cover 1 Remove the two screws attaching the lower cover to the dishwasher.
INSTALLATION 17 Attaching Mounting Hardware 1 Insert the installation brackets into the slots in the upper frame. 2 1 2 Make sure the drain hose inside the cabinet is not kinked or pinched. 3 Make sure the water supply line and electrical supply are routed through the channels under the dishwasher. 4 To avoid a kinked or pinched drain hose, be sure to pull on the drain hose while sliding the dishwasher into place. Do not allow any slack behind the dishwasher.
18 INSTALLATION Leveling the Appliance Adjusting the Legs Check that dishwasher is level. Adjusting the Front Legs ••Attach level on top front opening of tub from side to side. ••Use a flat-blade screwdriver or a pliers to turn the front legs and adjust the front of the tub. ••Attach level on front side of tub. ••Turn the front legs clockwise to raise the front of the tub and counter-clockwise to lower it. ••The adjustments work identically for both front legs.
INSTALLATION 19 Securing Dishwasher to Countertop Connecting Drain Hose For countertops made of granite, marble, or other materials that could be damaged by drilling, use Method 2. NOTE ••Cover the filter hole with towels to prevent screws from falling down into the pump. ••Use a magnetic screwdriver. Method 1 Using the provided screws, secure the dishwasher to the countertop through the holes in the bracket. 40" (1016 mm) max. 12" (305 mm) min.
20 INSTALLATION NOTE ••If the knockout plug has not been removed, the dishwasher will not be able to drain properly. Connecting to Disposal with No Air Gap 1 Connecting to Disposal or Waste Tee with Air Gap 1 Remove the knockout plug with a hammer and screwdriver. 2 Connect end of the drain hose to the air gap with hose clamp provided. This avoids water being siphoned from the tub. Remove the knockout plug with a hammer and screwdriver.
INSTALLATION 21 Connecting Water Supply 1 Before connecting, turn off the water supply. Slide the flexible stainless-steel water line or copper tube into the elbow. 3 Tighten the compression nut and make sure that the line is not kinked or pinched. ENGLISH 2 Connecting Power NOTE ••The best location for the electrical conduit is on the right side of the back wall. Re-route the power cable before installation if the electrical conduit pipe is longer than 3" (76 mm) and is centered on the back wall.
22 INSTALLATION Final Check 1 Turn on electrical power. 2 Turn on house water supply. 3 Make sure the door opens and closes smoothly. If necessary, level the dishwasher again. 4 Run the dishwasher on a Turbo cycle to verify proper operation and check for leaks. Error Code Possible Cause and Solution Drain hose kinked or pinched. OE Error Feed the drainage and supply hoses through the hole under the sink.
