Measurement Guide

24" (610 mm) min.
()
24" (610 mm) min
33
/
2
2
"
(
851 mm
)
min.
1
2
4"
(
610 mm
)
min.
LUDP8997SN
QUICK INSTALL
& CLEARANCES
For full installation directions/clearances
please refer to the corresponding
User Manual and Installation Guide.
DIMENSIONS/CLEARANCES/WEIGHT
Unit Dimensions (WxHxD) 23.75" x 33.6" x 24.6"
Depth with Door Closed (Handle) 27-1/8"
Depth with Door Open 50.5"
Carton Dimensions (WxHxD) 28" x 34.7" x 29.6"
Clearances (WxHxD) 24" x 33.5" x 24"
Weight (Unit / Carton) 83.8 lbs / 97.0 lbs
ENERGY / WATER
Water Factor (WF) 2.8
Energy Use (kWh/Year) 258 kWh/Year
ENERGY STAR® Qualified Yes
CEE Tier 1
23
/
4
"
(
603 mm
)
3
9
/
8
"
(
238 mm
)
3
/
/
4
/
16
"
(1
19 mm
)
5
/
4
"
(
134 mm
)
11
1
4
/
2
"
(
115 mm
)
1
33
/
16
"
(
(
846 mm
)
5
4
/
2
"
(1
15 mm
)
1
33
/
8
"
(
854 mm
)
)
5
/
/
2
/
16
"
(
75 mm
)
15
/
/
20
/
16
"
(
512 mm
)
3
2
4
/
8
"
(
625 mm
)
5
4
/
4
"
(
120 mm
)
3
/
/
26
/
8
26
/
16
"
(
676 - 681 mm
)
51
/
8
-
26
3
Wa
Wa
ter supply hose, drain hose and electric cable should be passedter supply hose, drain hose and electric cable should be passed
through this areathrough this area
.
DIMENSIONS
9
4
PREPARING CABINET OPENING
This dishwasher is designed to fit a
standard dishwasher opening. An opening
may be needed on both sides to route
plumbing and electrical connections.
• Select a location as close to the sink as
possible for easy connections to water
and drain lines.
• To ensure proper drainage, install the
dishwasher no more than 12 ft. (3.65 m)
from the sink.
• If installing the dishwasher in a corner,
leave a minimum of 2" (50 mm) between
the dishwasher and the adjacent wall.
• To allow for proper clearance of plumbing
and electrical, use the template included
with the literature to determine the
clearance on the side of the cabinet
where the cabinet meets the back wall.
Using a 2 1/2" diameter hole saw, drill a
hole in the target area as shown on the
template.
PREPARING ELECTRICAL WIRING
• Operate this appliance with the correct voltage
as shown in this manual and on the rating
plate. Connect it to a dedicated, properly
grounded branch circuit which is protected by
a time delay fuse. Connect the appliance using
3-wires, including a ground wire.
• If an outlet and other power connector are
used, it should be in an accessible location
adjacent to and not behind the dishwasher and
within 4 ft (1.2 m) of the dishwasher's side.
• The wiring must be grounded properly. If
in doubt, have it checked by a qualified
electrician. Do not connect any other appliance to the same outlet.
• Route the wiring.
• Make sure the electrical cable is oriented in the right side channel.
4
/
2
" - 6
”
(1
1
5 mm -
1
5
2
mm
)
1
ectrical ca
E
Ele
le
il b
ec
ct
tr
ric
ic
ca
al
c
ca
ab
ble
le
PREPARING WATER SUPPLY CONNECTION
Make sure the house water supply is turned off
before connecting the dishwasher water lines.
• Connect the dishwasher to a hot water
supply with a temperature range between
120 °F (49 °C) and 149 °F (65 °C). This
temperature range provides the best washing
results and shortest cycle time. To prevent
damage to dishes, the temperature should
not exceed 149 °F (65 °C).
• When connecting the dishwasher water
line, sealing tape or compound should be
used on pipe threads to avoid leaks. Tape or
compound should not be used on compression fittings.
• The water supply tube must be located in the left side channel.
6
/
2
-
7
/
4
"
(165 mm - 197 mm)
13
/
2
"-7
Wa
Wa
Wa
a
ter supply line
te
te
er
s
sup
up
pp
ply
ly
l
lin
ine
ne