Measurement Guide

WM9500HKA
QUICK INSTALL &
CLEARANCES
For full installation directions/clearances
please refer to the corresponding
User Manual and Installation Guide.
DIMENSIONS/CLEARANCES/WEIGHTS
A Width 29-5/8"
B Height 41-3/16"
C Depth 33-1/16"
D Depth with door open 55-15/16"
Carton (WxHxD) 31-5/16" x 44-15/16" x 35-5/8"
Weight (Product/Carton) 239 lbs / 263.3 lbs
POWER SOURCE
Ratings UL Listed
Electrical Requirements 120V, 10 Amps
Type Electric
1
"
1
"
A
B
4"
D
C
CONNECTING THE WATER LINES
Rubbe
r
S
ea
l
Wa
te
a
a
r
Hose
(
t
o
tap
)
Wa
te
a
a
r
Hose
(
t
o
wate
r
i
n
l
et
o
n
washe
r
)
r
R
ubber
S
ea
l
Wa
t
er
F
auc
e
t
Co
l
d
w
a
t
e
r inl
e
t
t
H
o
t
water in
l
e
t
t
t
LG recommends the use of LG hoses. Any leaking, property damage, or
damage to the washing machine caused by an improper installation or by
the use of non-LG hoses is not covered under the terms of the LG warranty
and is the sole responsibility of the customer and/or an installer.
•
Water supply pressure must be between 20 psi and 120 psi (138~827
kPa). If the water supply pressure is more than 120 psi, a pressure
reducing valve must be installed.
T
i
e
S
tr
a
p
39
”
(
9
9
c
m
)
39
”
(9
9
c
m
)
T
ie
S
tr
a
p
8”(20 cm
)
T
i
e
St
r
a
p
•
The drain hose should always
be properly secured. Failure
to properly secure the drain
hose can result in flooding and
property damage.
•
The drain must be installed in
accordance with any applicable
local codes and regulations.
•
Make sure that the drain hose
is not stretched, pinched, crushed, or
kinked.
•
Normal height of the end of the hose
should be approximately 35”~47”
(0.9~1.2 m) from the floor.
•
Inspect the threaded fitting on each hose
and make sure there is a rubber seal in
place in both ends of each hose.
•
Connect the water supply hoses to the
HOT and COLD water faucets tightly by
hand and then tighten another 2/3 turn
with pliers.
•
Always run a gallon or two of water
through each inlet hose to flush dirt,
scale and other debris out of the water
lines. Doing so will help prevent future
problems with clogged filter screens, and
will also allow you to verify which water
line is hot and which is cold.
•
Attach the hot water line to the hot water
inlet on the back of the washer. Attach
the cold water line to the cold water inlet
on the back of the washer. Tighten the
fittings securely. Turn ON both faucets all
the way and check for leaks at both ends
of the hoses.
D
r
a
in
Hose
STANDPIPE Option
LAUNDRY TUB Option
Otstynsxjwyymjjsitk
ymjiwfnsmtxjnsytymj
xyfsiunujrtwjymfsK
nshmjx"DBhr-/Doing so can
cause siphoning, odors, or
improper draining.
Otstyzxjymnxiwfnsmtxj
|nymfņttwiwfns/_mjjsi
tkymjiwfnsmtxjrzxygjfy
qjfxyDInshmjxfgt{jymjņttw
ktwuwtujwiwfnsnslytthhzw/
•
Do not install the end of the drain hose lower
than
29 in. (73.7 cm) or higher than 96 in. (243.8 cm)
above the bottom of the washer or more than
60 in.
(152.4 cm) away from the washer.
•
Never create an airtight seal between the hose
and the drain with tape or other means. If no air
gap is present, water can be siphoned out of the
tub resulting in poor wash/rinse performance or
clothing damage.
•
The washer should be plugged into a 120-VAC, 60-Hz
grounded 3-prong outlet. Plug in the washer. Improper
connection of the equipment-grounding conductor can
result in risk of electric shock. Check with a qualified
electrician or service technician if you are in doubt as
to whether the appliance is properly grounded. Do not
modify the plug provided with the appliance. If it does
not fit the outlet, have a proper outlet installed by a
qualified electrician. Failure to follow these warnings
can cause serious injury, fire, electrical shock, or death.
•
The power outlet must be within 60 inches (1.5 m) of
either side of the washer.
•
The appliance and outlet must be positioned so that
the plug is easily accessible.
•
Do not overload the outlet with more than one
appliance.
•
The outlet must be grounded in accordance with
current wiring codes and regulations.
•
Time-delay fuse or circuit breaker is recommended.
•
It is the personal responsibility and obligation of the
product owner to have a proper outlet installed by a
qualified electrician.
CONNECT TO THE POWER SUPPLY
DIMENSIONS / CLEARANCES
•
Install the washing machine on a solid floor that is strong and rigid
enough to support the weight of the washing machine, even when fully
loaded, without flexing or bouncing. If the floor has too much flex, you
may need to reinforce it to make it more rigid. If the floor is not solid, it
may cause severe vibration and noise.
CONNECTING THE DRAIN HOSE