Installation Guide

ManualsBrandsLG SIGNATURE ManualsAppliances5.8 cu. ft. High-Efficiency Front Load Washer with TurboWash and Steam in Black Stainless Steel, ENERGY STAR

9INSTALLATION

ENGLISH

INSTALLATION

Installation Overview

Please read the following installation instructions rst after purchasing this product or transporting it to another

location.

Choosing the proper location Unpacking and removing

shipping bolts

Connecting the water line

Connecting the drain line Leveling the washer Connecting to the power

supply

Testing the washer

WARNING

• Moving or installation of the appliance requires two or more people. Failure to follow these instructions may

result in injury.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious injury,

re, electric shock, or death.

• Properly ground the washer to conform with all governing codes and ordinances. Failure to follow this

warning can cause serious injury, re, electric shock, or death.

• To reduce the risk of electric shock, do not install the appliance in humid spaces. Failure to follow this

warning can cause serious injury, re, electric shock, or death.

• To ensure proper air ow, do not block the large opening on the bottom of the washer with carpeting or

other materials.

• Do not remove the ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong

outlet. Failure to follow this warning can cause serious injury, re, electric shock, or death.

Summary of content (8 pages)

PAGE 1
INSTALLATION 9 INSTALLATION Please read the following installation instructions first after purchasing this product or transporting it to another location. Choosing the proper location Unpacking and removing shipping bolts Connecting the water line Connecting the drain line Leveling the washer Connecting to the power supply Testing the washer WARNING • Moving or installation of the appliance requires two or more people. Failure to follow these instructions may result in injury.
PAGE 2
10 INSTALLATION Product Specifications The appearance and specifications listed in this manual may vary due to constant product improvements. Model WM9500H*A Electrical requirements 120 VAC @ 60 Hz Min. / Max. water pressure 20 – 120 psi (138–827 kPa) Dimensions 75.2 cm (W) X 86.4 cm (D) X 104.
PAGE 3
INSTALLATION 11 Choosing the Proper Location NOTE • Before installing the washer, make sure the floor is clean, dry and free of dust, dirt, water and oil so the washer feet cannot slide easily. Leveling feet that can move or slide on the floor can contribute to excess vibration and noise due to poor contact with the floor. • If a drip pan must be used, take extra care to follow the instructions provided with the drip pan and make sure the leveling feet are adjusted for firm and even contact with the pan.
PAGE 4
12 INSTALLATION Unpacking and Removing Shipping Bolts 1 Lift the washer off the foam base. After removing the carton and shipping material, lift the washer off the foam base. Make sure the plastic tub support comes off with the base and is not stuck to the bottom of the washer. If you must lay the washer down to remove the base packaging materials, always protect the side of the washer and lay it carefully on its side. Do not lay the washer on its front or back.
PAGE 5
INSTALLATION 13 Connecting the Water Lines 1 Check the fittings and seals. Rubber seal Rubber seal Attach the water lines to the back of the washer. Attach the hot water line to the hot water inlet on the back of the washer. Attach the cold water line to the cold water inlet on the back of the washer. Tighten the fittings securely. Turn ON both faucets all the way and check for leaks at both ends of the hoses.
PAGE 6
14 INSTALLATION Connecting the Drain Hose NOTE • The drain hose should always be properly secured. Failure to properly secure the drain hose can result in flooding and property damage. Option 2: Laundry Tub 1 Connect the elbow bracket within 4 inches (10 cm) of the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold or microorganisms could spread to the inside of the washer.
PAGE 7
INSTALLATION 15 Leveling the Washer 4 NOTE • Adjust the leveling feet only as far as necessary to level the washer. Extending the leveling feet more than necessary can cause the washer to vibrate • Before installing the washer, make sure that the floor is clean, dry and free of dust, dirt, water and oil so the washer feet cannot slide easily. Feet that move or slide on the floor can contribute to excessive vibration and noise due to poor contact with the floor.
PAGE 8
16 INSTALLATION Connecting to the Power Supply The washer should be plugged into a 120-VAC, 60 Hz grounded 3-prong outlet. Plug in the washer. WARNING • Do not use a worn or damaged power cord or power plug. Replace or repair it immediately. Failure to do so may result in death, fire, electric shock, or malfunction. • Do not modify the power cord and plug provided with the appliance. Take care not to damage it when installing or moving the washer.