INSTALLATION 9 Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location. 1 Unpacking your refrigerator 4 Connecting the water supply and water line 2 Choosing the proper location 5 Leveling and Door Alignment Note Connect to potable water supply only.
10 INSTALLATION Specifications ENGLISH The appearance and specifications listed in this manual may vary due to constant product improvements. Bottom-freezer refrigerator model LSFD2491** Description French door refrigerator Electrical requirements 115 VAC @ 60 Hz Min. / Max. Water pressure 20 – 120 psi (138 – 827 kPa) Dimensions 35 3/4” (W) X 30 7/8” (D) X 70 1/4” (H), 42 3/4” (D w/ door open) 908 mm (W) X 784 mm (D) X 1782 mm (H), 1085 mm (D w/ door open) Net weight 326 lb.
INSTALLATION Unpacking Your Refrigerator yyUse two or more people to move and install the refrigerator. Failure to do so can result in back or other injury. yyYour refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur. yyKeep flammable materials and vapors, such as gasoline, away from the refrigerator.
12 INSTALLATION Ambient Temperature ENGLISH Install this appliance in an area where the temperature is between 55°F (13°C) and 110°F (43°C). If the temperature around the appliance is too low or high, cooling ability may be adversely affected. Removing/Assembling the Refrigerator Door Handles Note When it is necessary to move the refrigerator through a narrow opening, removing the doors is the recommended procedure. If it is necessary to remove the handles, follow the directions below.
INSTALLATION 13 Removing/Assembling the Doors and Drawers Removing the Handles When it is necessary to move the refrigerator through a narrow opening, removing the doors is the recommended procedure. 1 2 Loosen the set screws located on the lower side of the handle with a 1/8 in. Allen wrench and remove the handle. Loosen the mounting fasteners connect to the freezer drawer and handle using a 1/4 in. Allen wrench, and remove the mounting fasteners.
14 INSTALLATION Removing the Left Refrigerator Door ENGLISH 1 4 The water supply is connected to the upper right part of the rear surface of the refrigerator. Remove the ring in the joint area. Hold the water supply connection and gently push the Collet to detach the water supply line as shown in and . Rotate the hinge lever counterclockwise . Lift the top hinge free of the hinge lever latch.
INSTALLATION 1 3 Rotate the hinge lever Lift the top hinge lever latch. clockwise. free of the hinge Remove the top hinge cover screw . Lift the hook (not visible), located at the bottom of the front side of the cover , with a flat-head screwdriver. Hinge Lever Latch Caution When lifting the hinge free of the hinge lever latch, be careful that the door does not fall forward. 2 Detach the wire harness . 4 Lift the door from the middle hinge pin and remove the door.
16 INSTALLATION Assembling the Right Refrigerator Door ENGLISH Install the right-side door first. 1 2 3 Connect the wire harness 4 Make sure that the door-switch located inside the cover is tightly connected. Position the cover in its place. Insert and tighten the cover screw . . Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin as shown in the figure. Fit the hinge over the hinge lever latch and slot it into place.
INSTALLATION 4 Push the water supply tube into the hole on the top case and pull it through the backplate. 5 Hold the water supply connection and gently push in the collet to connect the water supply line as shown in and . Insert the tube at least 5/8 inch (15 mm) into the connector. Assemble the clip to the joint part for fastening. Install the left refrigerator door after the right door is installed. 1 2 Make sure that the plastic sleeve is inserted in the bottom of the door.
18 INSTALLATION Removing the Freezer Drawers Note ENGLISH In the following figures, the Pullout Drawer located above the freezer drawer is not shown for clarity. Collet Tube Caution Insert Line Clip 1) Gently press the Collet and insert the tube until only one line shows on the tube. (Correct) yyUse two or more people to remove and install the freezer drawer. Failure to do so can result in back or other injury. yyDo not hold the handle when removing or replacing the drawer.
INSTALLATION Pull the drawer open to full extension. 2 Gently lift and pull out the ice bin. On the left rail, use a flat blade screwdriver to push in on the tab to release the drawer from the rail, as shown below. Once the left side is loose, push the tab on the right side with your finger to release the drawer. Lift the front of the drawer up, then pull it straight out. 3 Remove the screws from the rails at both ends. 4 Grip both sides of the drawer and pull it up to remove it from the rails.
20 INSTALLATION Assembling the Freezer Drawers ENGLISH 1 ull out both rails simultaneously, until both P rails are fully extended. 2 Grasp the drawer on each side and hook the drawer supports into the rail tabs located on both sides. Caution Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury. 3 Lower the door into its final position and tighten the screws located on both sides.
INSTALLATION 21 Connecting the Water Line This water line installation is not covered by the refrigerator warranty. Follow these instructions carefully to minimize the risk of expensive water damage. Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and can lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.
22 INSTALLATION ENGLISH yy If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting. yy Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 in. at the point of connection to the COLD WATER LINE.
INSTALLATION 23 4 7 CONNECT THE TUBING TO THE VALVE Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve. Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely. Pipe Clamp Saddle-Type Shutoff Valve Saddle-Type Shutoff Valve Compression Nut Vertical Cold Water Pipe Packing Nut Note Outlet Valve Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to.
24 INSTALLATION 10 ENGLISH TURN THE WATER ON AT THE SHUTOFF VALVE Tighten any connections that leak. Caution Check to see if leaks occur at the water line connections. 11 PLUG IN THE REFRIGERATOR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall. 12 START THE ICEMAKER Turn the icemaker on at the control panel.
INSTALLATION 25 Leveling and Door Alignment Door Alignment After installing, plug the refrigerator’s power cord into a 3-prong grounded outlet and push the refrigerator into the final position. The left refrigerator door has an adjustable nut, located on the bottom hinge, to raise and lower the door for proper alignment. Your refrigerator has two front leveling legs— one on the right and one on the left. Adjust the legs to alter the tilt from front-to-back or sideto-side.
