PLASMA TV OWNER’S MANUAL Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.
Safety Warnings Safety Instructions WARNING W Do not place the set in direct sunlight or near heat sources such as heat registers, stove and so on. - This may cause a fire. Do not use the set in damp place such as a bathroom or any place where it is likely to get wet. - This may cause a fire or could give an electric shock. Do not use water while cleaning the set. - This may cause damaged the set or could give an electric shock.
ENGLISH Safety Warnings * Safety instructions have two kinds of information, and each meaning of it is as below. WARNING The violation of this instruction may cause serious injuries and even death. NOTES The violation of this instruction may cause light injuries or damage of the product. Take care of danger that may happen under specific condition. NOTES Never touch the power plug with a wet hand. - This may cause an electric shock.
Contents Contents Safety Warnings Safety Instructions . . . . . . . . . . . . . . . . . . . . . . .2~3 Introduction Remote Control Key Functions . . . . . . . . . . . . . . . .5 Location and Function of Controls . . . . . . . . . . .6~7 Installation External Equipment Viewing Setups . . . . . . . . . . . .8 Displayable Monitor Specification . . . . . . . . . . . . . .9 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Accessories . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control Key Functions - When using the remote control aim it at the remote control sensor of the set. - There maybe a defect in consecutive operation of remote control in a specified brightness according to this set. INPUT Selects the TV, AV1, AV2, S-Video, AV3, AV4, AV5, Component, RGB or HDMI modes. switches the set on from standby. MODE Selects another device. VCR BUTTONS Controls a video cassette recorder. These buttons are used for X-Studio. For further details, see the ‘X-Studio’ section.
Introduction Location and Function of Controls - Shown is a simplified representation of the set. - Here shown may be somewhat different from your set. 10 7 8 9 1 2 INPUT MENU OK 3 4 5 1. Remote Control Sensor 2. Power Button Switches the set on from standby or off to standby. 3. INPUT Button Selects the TV, AV1, AV2, S-Video, AV3, AV4, AV5, Component, RGB or HDMI modes.switches the set on from standby. 4. MENU Displays on screen menus one by one. Exits the current menu.
Introduction ENGLISH Location and Function of Controls AV5 VIDEO S-VIDEO R AUDIO L/MONO 9 VIDEO AUDIO L HDMI/ DVI(VIDEO) AUDIO INPUT R AV2 VARIABLE V ARIABLE AUDIO OUT RS-232C INPUT (CONTROL/SERVICE) Antenna AUDIO L REMOTE CONTROL AC INPUT AV1 R COMPONENT RGB INPUT AV4 AV3 L S-VIDEO VIDEO R (MONO) AUDIO 1 2 3 4 1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUT Connect the monitor output socket of the PERSONAL COMPUTER, DVD or STB to this socket.
Installation External Equipment Viewing Setups VIDEO AUDIO L HDMI/ DVI(VIDEO) AV1 R L REMOTE CONTROL R AV2 VARIABLE V ARIABLE AUDIO OUT RS-232C INPUT (CONTROL/SERVICE) Antenna AUDIO COMPONENT RGB INPUT AUDIO INPUT AV4 AV3 L S-VIDEO VIDEO R (MONO) AUDIO AV1 Connection to PC 8 PLASMA TV Connection to AV equipment
Installation ENGLISH Displayable Monitor Specification RGB / HDMI mode 42PX4R / 42PX5R Series Resolution 640x350 720x400 640x480 848x480 50PX4R / 50PX5R Series Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 35.000 Resolution 640x350 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 59.94 31.469 59.94 66.66 35.000 66.66 720x400 640x480 37.861 72.80 37.861 72.80 37.
Installation - HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing. - This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI). - This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
Installation ENGLISH Accessories MULTIMEDIA TV/AV POWER DVD TV VCR MODE CABLE STB AUDIO ZOOM - ZOOM + PIP TEXT/ * SLEEP MUTE LIST I/II ARC EXIT MENU OK PIP PR - PIP PR + VOL SWAP PIP INPUT PR SSM PSM SIZE POSITION INDEX HOLD TIME REVEAL MIX MODE FAVOURITE Q.VIEW ? M LG TV AS mark Owner’s Manual Remote Control handset 2-Eye Bolts Power Cord 2-Wall brackets 1.5V 1.
Installation Installation Options • The set can be installed in different ways such as on a wall, or on a desktop etc. • Install this set only in a location where adequate ventilation is available. Wall Mount: Horizontal Installation Desktop Pedestal Installation • The set can be installed on a wall as shown above. (For further information, refer to the optional ‘Wall Mounting Bracket Installation and Setup Guide’.) To Mount on a Wall Wall mount minimum allowable clearances for adequate ventilation.
Operation ENGLISH Turning on the Set - When using the remote control, aim it at its sensor on the set. Turning on the set just after installation 1. Connect power cord correctly, the set is switched to standby mode. 2. Press the r / I, INPUT or PR D / E button on the set or press the POWER, INPUT, MULTIMEDIA, PR NUMBER buttons on the remote control and then the set will switch on.
Operation On screen menus - The dialogue between you and your set takes place on screen with an operator menu. The buttons required for the operating steps are also displayed. Menu selection 1. 2. 3. Press the MENU button and then D / E button to display each menu. Press the G button and then the F / G button to select a menu item. Repeatedly press the MENU button to return to normal TV viewing.
Channel Menu Options Auto Programme Tuning - All stations that can be received are stored by this method. It is recommended that you use auto programme during installation of this set. 1. Press the MENU button and then use D / E button to select the STATION menu. STATION PICTURE Auto programme programme G Auto Manual programme Programme edit Favourite programme System BG Storage from 2 Start SOUND TIME SPECIAL SCREEN PIP/DW Menu Prev. 2.
Operation Channel Menu Options Assigning a Station Name 1. Repeat the ‘Manual programme tuning’ steps 1 to 2. 2. Press the G button and then D / E button to select Name. 3. Press the G button to display the Name menu. STATION Auto programme Manual programme Manual programme PICTURE Programme edit Favourite programme Storage 2 System BG Band SOUND V/UHF 1 Channel TIME Fine Search SPECIAL Name C 01 SCREEN Booster PIP/DW Off Prev. 4. Press the D button.
Picture Menu Options PSM (Picture Status Memory) Manual Colour Temperature Control - This function adjusts the set to the best picture appearance. - When adjusting picture options (contrast, brightness, colour, sharpness and tint (NTSC input only)) manually, PSM is automatically changed to User. 1. Press the PSM button • Each press of the PSM button changes the screen display as shown below. - You can adjust red, green, or blue to any colour temperature you prefer.
Operation Sound Menu Options TV Speaker • DUAL I + II sends a separate language to each loudspeaker. - You can adjust the internal speaker status. - In COMPONENT RGB[PC] and HDMI[PC] mode, TV speaker and/or variable audio can be outputted even though there is no video signal. - If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
Special Menu Options Child Lock - The set can be set up so that it can only be used with the remote control. - This set is programmed to remember which option it was last set to even if you turn the set off. - In Child lock ‘On’, if the set is turned off, press the INPUT, PR D / E button on the set or POWER, INPUT, MULTIMEDIA, PR D / E or NUMBER buttons on the remote control.
Operation Screen Menu Options Setting the Picture Format - You can watch the screen in various picture formats; Spectacle, Full (option), Original, 4:3, 16:9 (Wide), 14:9 and Zoom. • Spectacle When your TV receives the wide screen signal, when selected it will adjust the picture horizontally, in non-linear proportion, to fill the entire screen.
Operation SIMPLE Text (option) Page selection 1. Enter the desired page number as a three digit number with the NUMBER buttons. If during selection you press a wrong number, you must complete the three digit number and then reenter the correct page number. 2. The PR D / E button can also be used to select the preceding or following page. Programming a colour button in LIST mode If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the M button to switch to LIST mode.
Operation PIP (Picture-in-Picture) Feature - PIP lets you view 2 different inputs (sources) on your set screen at the same time. - It’s not available to use this function in TELETEXT mode. Watching PIP Press the PIP button to show the sub picture. • Each press of PIP button changes the screen display as shown below. RGB AV1 RGB AV1 RGB AV1 10:30 10:30 10:30 RGB AV1 RGB 10:30 10:30 Note : a. When the sub picture size is 1/2 of the main picture, the picture quality may decrease. b.
- You can use the JPEG and MP3 file by memorizing to Memory card in ENGLISH Operation mode. Notes on Memory Card When removing or handling the memory card, use only your hands. Do not use other devices or the memory card may be damaged. Memory Card This is a device equiped to communicate the data between AV external equipment. It’s used in a digital camera, camcorder, MP3 player, notebook or PDA.
Operation Notes on Memory Card Available Memory Card Slot 2 * Check the direction of the Memory card. (refer to the pictures below) Slot 1 Memory Card type - Use the specified card based on the slot location. - 8 types of Memory Card can be used for this set. - NTFS file system is not supported.
ENGLISH Operation The JPEG Decoding/The Image Preview Supplied Spec Compression Method Colour format 4:2:2 4:4:4 4:2:0 21:11:11 (Y, Cb, Cr) 11:11:11 (Y, Cb, Cr) 12:11:11 (Y, Cb, Cr) 22:11:11 (Y, Cb, Cr) Baseline Progressive JPEG Decoding Support O X X O O Image Display Image invalid format invalid format Image Image Preview Image Display Display when there is no thumbnail. Display when there is no thumbnail. Display when there is no thumbnail.
Operation JPEG File Viewing Viewing Options - When you select Photo in entry menu, you will now see a screen filled with thumbnail photo media. * In this manual, the OSD (On Screen Display) may be different from your set’s because it is just an example to help you with the set operation. Screen Components Current page/Total page Marked JPEG file number Card type Usable Card memory/ Total Card memory Left Menu Direct Buttons Photo Selection and PopUp menu - Select your desired image file.
ENGLISH Operation Mark/Unmark for JPEG file - You can mark/unmark the file to view the desired file or use slide show for desired file conveniently. - The selected file displays orange in colour. When pressing the OK button after marking a file, the marked file displays green in colour. W Mark/Unmark for all files 1. In photo media, repeatedly press 2. Press the D /E F button to enter the menu on the left. button to select Mark All or Unmark All. • If you select Mark All, every file is selected.
Operation JPEG File Viewing Viewing Options The Image Adjustment - You can display the selected image on the entire screen and do the various adjustments for the JPEG file. View Slide Show Delete Cancel 1. Press the D /E /F /G 2. Press the D /E button to select JPEG file and then press the OK button. button to select View and then press the OK button The selected image will display on entire screen. F G Prev./Next Image selection Image Rotation Rotate PR G 1/15 F G 3. Adjust the JPEG file.
ENGLISH Operation Slide Show 1. Press the D / E / F / G button to select JPEG file and then press the OK button. 2. Press the D / E button to select Slide Show or Show Marked and then press the OK button. (If you mark the file with using MARK button, Show Marked is displayed on screen.) View Slide Show Delete Cancel 3. You can choose the slide show delayed time and effect. Press the D / E / F / G button to choose the slide show delayed time and effect.
Operation JPEG File Viewing Viewing Options JPEG file Deletion and Cancel View Slide show Delete Cancel 1. Use the D /E /F /G button to select JPEG file and then press the OK button. 2. To delete the file, press the D / E button to select Delete and then press the OK button. When “Do you want to delete the file?” message is displayed, select YES (YES or NO) with F / G button. The file is deleted, all the following files are shifted up one position.
MP3 File Playing Operation - Purchased MP3/music files may contain copyright restrictions. Playback of these files may not be supported by this model. Screen Components Current Playing Time/Total Playing Time G : Play II : Pause A : Stop Current file number/Total file number Marked MP3 file number Card type Using Card memory/ Total Card memory Left Menu Direct Buttons MP3 File Selection and Playback - MP3 file Selection and deletion function don’t work while playing music.
Operation MP3 File Playing Operation * In this manual, the OSD (On Screen Display) may be different from your set’s because it is just an example to help you with the set operation. Stop/Pause Playback W Stop Playback To stop playback, press the A button on the remote control. To stop playback, press the OK, PR (D / E) button on the set. Notes: • If you replay the MP3 file after stopping, the highlighted MP3 file on menu will play.
ENGLISH Operation Jump Media - Use this funcion to jump to other media during using music media. Please select where to move Memory 1 MS/Pro Photo Music Memory 2 CF/MD Photo Music Cancel 1. In music media, press the 2. Press the D /E F button. button to select Jump media and then press the OK button. 3. Press the D / E / F each media list. /G button to select desired media and then press the OK button.
Operation MP3 File Playing Operation MP3 file deletion and Cancel - It’s impossible to delete the music during playback. Play Delete Cancel 1. Use the D /E button to select MP3 file and then press the OK button. 2. To delete the file, press the D / E button to select Delete and then press the OK button. When “Do you want to delete the file?” message is displayed, select YES (YES or NO) with F / G button. The file is deleted, all the following files are shifted up one position.
Programming the Remote G The remote is a multi-brand or a universal remote. It can be programmed to operate most remote-controllable devices of other manufacturers. Note that the remote may not control all models of other brands. Programming a code into a remote mode 1. To find out whether your remote can operate the device without programming, turn on the device such as a VCR and press the corresponding mode button on the remote. After that, press the POWER button.
Miscellaneous Programming Codes VCRs Brand Codes Brand Codes Brand Codes Brand Codes AIWA AKAI 034 016 125 072 031 012 035 028 108 003 031 005 065 112 108 012 034 059 006 029 036 129 003 034 031 107 132 012 004 043 031 031 012 040 043 012 048 130 KENWOOD 014 047 001 101 034 003 017 040 031 067 012 069 101 027 031 003 033 101 045 013 013 049 151 034 024 012 048 043 053 066 133 013 063 031 031 067 101 013 PORTLAND PULSAR QUARTZ QUASAR RCA 108 072 011 033 013 040 107 145 003 031 053 058 148 014 0
ENGLISH Miscellaneous HDSTB Brand Codes Brand ALPHASTAR DSR AMPLICA BIRDVIEW CHANNEL MASTER 123 050 051 013 036 008 054 050 005 011 141 024 038 093 097 122 089 114 017 133 GENERAL INSTRUMENT 003 031 HITACHI 139 HOUSTON TRACKER 033 057 HUGHES 068 JANIEL 060 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 MACOM 010 065 MEMOREX 057 NEXTWAVE 028 NORSAT 069 CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME EUROPLUS FUJITSU 126 129 014 015 018 055 009 012 077 145 006
Miscellaneous Troubleshooting Checklist • Check whether the set is turned on. No picture & No sound • Power cord inserted into wall outlet? • Plug another product’s power cord into the wall outlet where the set’s power cord was plugged in. • Press the VOLUME (D) button. Picture OK & No sound • Sound muted? Press MUTE button. • Check whether the TV speaker is “on” in the SOUND menu. • Check to see if there is any object between the set and the remote control causing obstruction.
Miscellaneous • ENGLISH Product Specifications 42PX4R / 42PX4RH 50PX4R / 50PX4RH MODEL 42PX4R-ZB / 42PX4RH-ZB 50PX4R-ZB / 50PX4RH-ZB Width (inches / mm) 49.3 / 1252 57.6 / 1461 Height (inches / mm) 27.78 / 705.5 32.9 / 835 Depth (inches / mm) 11.29 / 286.7 13.1 / 331.3 Weight (pounds / kg) 70.06 / 31.78 121.7 / 55.