English OWNER'S MANUAL CLOUD MONITOR Please read the safety information carefully before using the product. CLOUD Monitor Model 19CNT42K www.lg.
Table of Contents TABLE OF CONTENTS English ENG 3 ASSEMBLING AND PREPARING 22 TROUBLESHOOTING 3 Unpacking 4 Parts and buttons 24 PRODUCT SPECIFICATION 5 Lifting and moving the Monitor 25 Preset Mode 5 Setting Up the Monitor set 25 Power Indicator 5 - Attaching the Stand Base 6 - Detaching the stand base 6 - Detaching the stand body 26 PROPER POSTURE 7 - Mounting on a table 26 Proper posture for using the monitor 7 - Adjusting the stand height 8 - Adjusting the angle 27
ASSEMBLING AND PREPARING 3 ASSEMBLING AND PREPARING ENG English Unpacking Please check whether all the components are included in the box before using the product. If there are missing components, contact the retail store where you purchased the product. Note that the product and components may look different from those shown here. User Manual/Card Stand Base Power Cord Adaptor 15-pin D-SUB Signal Cable CAUTION Only use an approved LG power adapter.
ASSEMBLING AND PREPARING Parts and buttons English ENG Input Connectors (See p.14 ) Power Indicator yyLED On : Power is on yyLED Off: Power is off (Power Button) MENU 92/ CLOUD AUTO INPUT EXIT Front Side Buttons 1 1 Input Connectors (See p.
ASSEMBLING AND PREPARING Please heed the following information when moving the monitor. CAUTION yyAvoid touching the screen at all times, as this may result in damage to the screen or pixels . Setting Up the Monitor set Attaching the Stand Base 1 Place the monitor's screen face down. CAUTION To protect the screen from scratches, yy cover the surface with a soft cloth.
ASSEMBLING AND PREPARING English ENG Detaching the stand base Detaching the stand body 1 Place the monitor's screen face down. 1 Place the monitor's screen face down. To To protect the screen from scratches, cover the surface with a soft cloth. protect the screen from scratches, cover the surface with a soft cloth. 2 Using a screwdriver, remove the four screws and detach the stand from the monitor. 2 Using a coin, turn the screw in the stand base counterclockwise.
ASSEMBLING AND PREPARING Adjusting the stand height 1 Lift the monitor and place it on the table in an 1 Place the monitor mounted on the stand base Install at least 10 cm away from the wall to ensure sufficient ventilation. 2 Remove the tape attached at the bottom rear upright position. in an upright position. of the stand body, then pull out the locking pin. 10 cm 10 cm 10 cm Stand Body 10 cm Tape Locking Pin 3 The height can be adjusted up to 130.0 mm. 130.
ASSEMBLING AND PREPARING Adjusting the angle English ENG 1 Place the monitor mounted on the stand base in an upright position. 2 Adjust the angle of the screen. The angle of the screen can be adjusted up to 5° forwards and 15° backwards for a comfortable viewing experience. 15 Rear Side -5 Using the Kensington locking device The connector for the Kensington lock is located on the rear of the monitor.
ASSEMBLING AND PREPARING Swivel stand 1 Swivel 356 degrees and adjust the angle of the Monitor set to suit your view. Using the Pivot function The pivot function allows you to rotate the screen 90 degrees clockwise. 1 Lift the monitor to its highest height to utilize the Pivot function. 2 Landscape & Portrait : You can rotate the panel 90o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the screen to access the Pivot function.
ASSEMBLING AND PREPARING English ENG Installing the wall mount plate Mounting on a wall This monitor has a VESA compatible mount on the back. Most mounts will require an LG mounting plate. Install the monitor at least 10 cm away from the wall and leave about 10 cm of space at each side of the monitor to ensure sufficient ventilation. Detailed installation instructions can be obtained from your local retail store. Please refer to the manual to install and set up a tilting wall mounting bracket.
ASSEMBLING AND PREPARING Model 11 19CNT42K CAUTION Unplug the power cord before moving or inyy stalling the monitor to avoid electric shocks. Installing the monitor on the ceiling or on a yy slanted wall may result in the monitor falling off, which could lead to injury. Please use a LG wall mounting bracket when using a VESA mount. For more information, contact your local retail store or a qualified installer. Applying excessive force when fastening yy screws may cause damage to the monitor.
USING THE MONITOR SET USING THE MONITOR SET English ENG Connecting Input Signal Cable This monitor supports the *Plug and Play yy feature. *Plug and Play: A feature that allows you to add a device to your computer, without having to reconfigure anything or install any manual drivers. D-SUB IN connection - PC Self Image Adjustment Press the power button on the front to turn on the monitor.
USING THE MONITOR SET 13 DVI connection LAN connection Transfers video signals to another monitor. Connect the monitor using the DVI cable as illustrated below. Connect the router or switch to the monitor using a LAN cable as illustrated below. DVI-I(D) IN MONITOR LAN Hub/Router NOTE The LAN cable is sold separately. yy The following LAN cable type can be used: yy Standard: IEEE 802.
USING THE MONITOR SET Peripheral device connection English ENG Connect peripheral devices to the monitor using USB, microphone and headphone ports. NOTE Peripheral devices are sold separately. yy The USB ports on the left and bottom of the yy monitor can be used to connect the keyboard, mouse, and other USB devices. Cables with angled plugs may have clearyy ance issues, use straight plugs when possible.
CUSTOMIZING SETTINGS 15 CUSTOMIZING SETTINGS ENG English Accessing The Main Menus 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press to select the desired menu item. 3 To change the settings of the selected item press the buttons on the front of the monitor. To return to the upper menu or set other menu items, use the up arrow ( 4 ) button. Select EXIT to leave the OSD menu.
CUSTOMIZING SETTINGS Customizing Settings English ENG Menu Settings 1 Press MENU button on the bottom of the Monitor set to display the MENU OSD. 2 Set the options by pressing the ◄ or ► or ▼ buttons. 3 Select the "NEXT MENU" button to enter the more option settings. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow ( ) button. VOLUME Each option is explained below.
CUSTOMIZING SETTINGS 17 PICTURE ENG English 1 Press MENU button on the bottom of the Monitor set to display the MENU OSD. 2 Select the "NEXT MENU" button to enter the more option settings. 3 Enter to PICTURE by pressing the ▼ button. 4 Set the options by pressing the ◄ or ► or ▼ buttons. 5 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow ( ) button. Each option is explained below.
CUSTOMIZING SETTINGS COLOR English ENG 1 Press MENU button on the bottom of the Monitor set to display the MENU OSD. 2 Select the "NEXT MENU" button to enter the more option settings. 3 Select COLOR by pressing the ► button. 4 Enter to COLOR by pressing the ▼ button. 5 Set the options by pressing the ◄ or ► or ▼ buttons. 6 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow ( ) button. Each option is explained below.
CUSTOMIZING SETTINGS 19 DISPLAY ENG English 1 Press MENU button on the bottom of the Monitor set to display the MENU OSD. 2 Select the "NEXT MENU" button to enter the more option settings. 3 Select DISPLAY by pressing the ► button. 4 Enter to DISPLAY by pressing the ▼ button. 5 Set the options by pressing the ◄ or ► or ▼ buttons. 6 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow ( ) button. Each option is explained below.
CUSTOMIZING SETTINGS OTHERS English ENG 1 Press MENU button on the bottom of the Monitor set to display the MENU OSD. 2 Select the "NEXT MENU" button to enter the more option settings. 3 Select OTHERS by pressing the ► button. 4 Enter to OTHERS by pressing the ▼ button. 5 Set the options by pressing the ◄ or ► or ▼ buttons. 6 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow ( ) button. Each option is explained below.
CUSTOMIZING SETTINGS 21 Volume (Only supported in CLOUD) ENG English 1 Press any button on the front of the monitor to display the MONITOR SETUP OSD menu. 2 Press the MENU button to display the options in the OSD menu. VOLUME 3 Set the options by pressing the buttons on the front of the monitor. 4 Select EXIT to leave the OSD menu. To return to the upper menu or set other menu items, use the up arrow ( ) button. MENU > NEXT MENU > VOLUME VOLUME Description To adjust the volume.
Troubleshooting TROUBLESHOOTING English ENG Nothing is displayed on the screen Is the monitor's power cord plugged in? yy Check if the power cord is correctly plugged in to the outlet. Is the power indicator on? yy Check the power indicator. Is the power indicator displaying as white? yy Adjust the brightness and the contrast. Is the power indicator blinking? yy If the monitor is in power saving mode, move the mouse or press any key on the keyboard to switch the display on.
Troubleshooting 23 The image is displayed abnormally. Pressing the AUTO button will automatically optimize the screen to the current display mode. Does the screen exhibit vertical lines? Pressing the AUTO button will automatically optimize the screen to the current display mode. Does the screen display horizontal Pressing the AUTO button will automatically optimize the screen to the current frequencies, or does the text appear display mode.
Specifications PRODUCT SPECIFICATION English ENG LCD Screen Type Resolution Pixel Pitch Maximum Resolution Video Signal Input Connector Power AC/DC Adapter Dimension/ Weight Weight (Without Packaging) Stand Angle Adjustment Environment Condition Recommended Resolution DVI-I output Horizontal Frequency Vertical Frequency Synchronization 15-pin D-SUB (Analog) 19 V 2.3 A Power Consumption(Typ.) (D-sub/CLOUD) 481.33 cm (18.
Product Specification 25 Preset Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Polarity (H/V) 720 x 400 31.468 70.08 -/+ 640 x 480 31.469 59.94 -/- 800 x 600 37.879 60.317 +/+ 1024 x 768 48.363 60 -/- 1280 x 1024 63.981 60.02 +/+ 1680 x 1050 65.290 59.954 -/+ 1920 x 1080 67.
Proper Posture PROPER POSTURE English ENG Proper posture for using the monitor Adjust the angle so that the screen is slightly lower than your eyes. Using the monitor for a prolonged period of time can cause eye fatigue. Take a 10-minute break every yy hour. The stand is designed to best support the monitor when the optimal conditions are selected. yy Adjust the angle of the monitor from -5° to 15° to obtain the best view of the screen. You should be looking slightly down at the screen.
Using CITRIX Solution 27 USING CITRIX SOLUTION Power Button This screen is displayed when power is turned on. Click the Power button to turn the system off or restart it in the login screen. Login Window Enter a user name, password and domain to access the VDI server. Power Off Menu Select the Power Off menu and then press the OK button in the Shutdown pop-up to terminate the system. Network status: If a network is connected, yy the text Connected appears with a green circle button.
Using CITRIX Solution Restart Menu English ENG Select the Restart menu and click the OK button in the Restart pop-up to restart the system. Settings button: You can set the network, server or language for using a network monitor. Language Set a language to use on the network monitor home screen. After setting the language, click the 'OK' button. The default is English. Network Set a wired/wireless network.
Using CITRIX Solution Wired connection setting Wireless setting The AP list for wireless network connection is yy displayed. Click the Refresh button to update the list of accessible APs. Double click an AP or click the Connect butyy ton after selecting an AP to access the AP. When the connection is established, the AP is marked as connected in the list. When you select a connected AP and then yy click the right mouse button, the Disconnect and Set-Up buttons are displayed.
Using CITRIX Solution Server English ENG Set Citrix VDI server and LGDMS server address. LGDMS is a network monitor management software provided by LG Electronics. VDI server setting Enter a VDI server address to access. yy Connect Automatically: ? yy DHCP setting: Set the DHCP mode. If it is yy set to On, an IP is automatically fetched from a DHCP server and used. Static connection setting: If DHCP is set to yy Off, the input window is displayed for detailed setting.
Using CITRIX Solution LGDMS setting Screen Output Setting Primary display setting Resolution: Select the resolution of a moniyy tor. The network monitor supports 5 resolutions including Auto, 1920x1080, 1680x1050, 1280,x1024 and 1024x769. When it is set to Auto, the monitor is automatically adjusted to the optimal resolution. Rotation: Set the angle of a LCD screen to yy normal, 90 degree counter-clockwise or 90 degree clockwise. ENG English Enter the address of LGDMS server to conyy nect to.
Using CITRIX Solution Secondary display setting English ENG Resolution: Select the resolution of a moniyy tor. Among the resolutions supported in the DVI monitor, 1024x768 or higher resolutions and Auto menu are displayed. When it is set to Auto, the monitor is automatically adjusted to the optimal resolution. Rotation: Set the angle of a LCD screen to yy normal, 90 degree counter-clockwise or 90 degree clockwise. Dual Monitor: You can specify the extension yy mode.
Using CITRIX Solution Factory reset Information button General Tab Display the hardware and software information of a network monitor. Hardware Information: Network monitor modyy el name, serial number and asset number. The asset number can be set in LGDMC Software information: Firmware version, softyy ware file name and publisher information Wake on LAN: Status of Wake on LAN yy NOTE yyWake on LAN can only be set in the LGMC. ENG English The system is reset to factory defaults and rebooted.
Using CITRIX Solution Network Tab English ENG Display network related information. Network Information: VDI/LGMS server IP yy address information Wired Connection: IP address and MAC adyy dress of a wired network Wireless Connection: IP address and MAC yy address of a wireless network Ping Tab By pinging, you check the network connection to a specific IP or host from a local client and also local network status. NOTE yyOnly IP or host name can be entered. The parameters of ping can not be used.
Make sure to read the Safety Precautions before using the product. Keep the Owner's Manual(CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.
