QUICK REFERENCE GUIDE LED TV* * LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your set and retain it for future reference. 22LT560C 26LT560C 32LT560C 37LT560C 42LT560C 32LT560E 37LT560E 42LT560E 47LT560E P/NO : MFL67415402 (1305-REV07) 55LS460E www.lgsolutions.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product. WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. Do not use this apparatus near water.
IMPORTANT SAFETY INSTRUCTIONS Protect the power cord from being walked on yy or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified yy by the manufacturer. Use only with a cart, stand, tripod, bracket, yy or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
IMPORTANT SAFETY INSTRUCTIONS Grounding yy (Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
IMPORTANT SAFETY INSTRUCTIONS DISPOSAL (Hg lamp only used in LCD TVs) The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with general household waste. Disposal of this product must be carried out in accordance to the regulations of your local authority.
LICENSES / OPEN SOURCE SOFTWARE NOTICE LICENSES Supported licenses may differ by model. For more information about licenses, 'visit www.lg.com'. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
TABLE OF CONTENTS 7 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 6 LICENSES 6 OPEN SOURCE SOFTWARE NOTICE 7 TABLE OF CONTENTS 8 INSTALLATION PROCEDURE 8 ASSEMBLING AND PREPARING 8 11 12 14 14 17 18 20 21 22 Unpacking Optional Extras Parts and buttons Setting up the TV - Attaching the stand - Mounting on a table - Mounting on a wall - External speaker out - Tidying cables Making Connections 23 REMOTE CONTROL 25 GENERAL TROUBLESHOOTING 25 CAUTION for using EzSign 2.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING INSTALLATION PROCEDURE 1 Open the package and make sure all the accessories are included. 2 Attach the stand to the TV set. 3 Connect an external device to the TV set. ASSEMBLING AND PREPARING Unpacking ENGLISH ENG Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.
ASSEMBLING AND PREPARING 9 (For LT560C series) ENERGY AV MODE INPUT TV SAVING 1 2 3 4 5 6 7 8 9 LIST 0 FLASHBK MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO Quick Reference Guide Power Cord (For 32/37/42LT560C) (For 22LT560C) (For 26LT560C) Stand Body, Stand Base (See p.14) Stand Body, Stand Base (See p.15) Stand Body, Stand Base (See p.15) (For 32/37/42LT560C) (For 22LT560C) (For 26LT560C) Stand Screws 8 EA, M4 x 14 (See p.
ASSEMBLING AND PREPARING (For LT560E series) ENERGY AV MODE INPUT TV SAVING 1 2 3 4 5 7 8 9 0 FLASHBK LIST 6 MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO Quick Reference Guide EzSign 2.0 Editor CD Power Cord Stand Body, Stand Base (See p.14) Stand Screws 8 EA, M4 x 14 (See p.14) Desk-Mount Screw (See p.17) Protection Cover ENGLISH ENG Remote Control, Batteries (AAA) (See p.23) (For 47LT560E) Power Cord Holder (See p.
ASSEMBLING AND PREPARING 11 (For LS460E series) ENERGY AV MODE INPUT TV SAVING 1 2 3 4 5 7 8 9 0 FLASHBK LIST 6 MARK FAV VOL 3D CH P A G E MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO Quick Reference Guide EzSign 2.0 Editor CD Power Cord Stand Body, Stand Base (See p.16) Stand Screws 8 EA, M4 x 20 (See p.16) Wall Mount Inner Spacers 4 EA (See p.19) Cable Holder (See p.
ASSEMBLING AND PREPARING Parts and buttons (For LT560C, LT560E series) Remote Control Power Indicator Side Connection Panel HDMI Input USB IN Buttons (For 22/26LT560C) IN 3 USB Input Screen Buttons (For 32/37/42LT560C, 32/37/42/47LT560E) ENGLISH ENG Speakers DC IN / DVI IN 1 2 R EXTERNAL SPEAKER OUT Rear Connection Panel L RS-232C IN (CONTROL & SERVICE) L/MONO -AUDIO- R (For 22/26LT560C) AV IN VIDEO RGB IN (PC) ANTENNA/ CABLE IN RJP INTERFACE AUDIO IN (RGB/DVI) Button Descrip
ASSEMBLING AND PREPARING 13 (For LS460E series) Screen Side Connection Panel USB IN USB Input 3 IN HDMI Input Remote Control and Intelligent1 Sensors Power Indicator OK AV IN RGB IN (PC) SETTINGS INPUT VIDEO 2 -AUDIO- R 1 L/MONO / DVI IN R EXTERNAL SPEAKER OUT L RS-232C IN (CONTROL & SERVICE) ANTENNA/ CABLE IN RJP INTERFACE Rear Connection Panel Touch Buttons2 AUDIO IN (RGB DVI) Touch button Description /I Turns the power on or off. INPUT Changes the input source.
ASSEMBLING AND PREPARING Setting up the TV You can mount your TV to a wall or attach the stand if you wish to place the TV on an entertainment center or other furniture. Attaching the stand If you are not mounting the TV to a wall, use the following instructions to attach the stand.
ASSEMBLING AND PREPARING 15 (For 22/26LT560C) 1 2 4 EA M4 x 12 Stand Body M4X20 Front CAUTION Stand Base Top View When attaching the stand to the TV yy set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. 3 M4 x 16 (For 22LT560C) 4 EA M4 x 12 (For 26LT560C) Caution Make sure that the screws are fastened yy completely. (If they are not fastened securely enough, the TV may tilt forward after being installed.
ASSEMBLING AND PREPARING (For 55LS460E) 1 4 EA Stand Body 2 M4 x 20 Front Stand Base Top View Caution When attaching the stand to the TV yy set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. ENGLISH ENG 3 4 EA M4 x 20 Caution Note Remove the stand before installing the TV yy on a wall mount by performing the stand attachment in reverse. Make sure that the screws are fastened yy completely.
ASSEMBLING AND PREPARING Mounting on a table 17 Adjusting the angle of the TV to suit view 1 Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. (For 32/37/42LT560C, 32/37/42/47LT560E) Swivel 90 degrees to the left or right and adjust the angle of the TV to suit your view.
ASSEMBLING AND PREPARING Using the Kensington security system (optional) (Depending on model) The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com. Attaching the TV to a desk The TV should be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product.
ASSEMBLING AND PREPARING Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.
ASSEMBLING AND PREPARING Securing the TV to a wall (optional) (Depending on model) External speaker out Connect the external speaker. (For 22/26/32/37/42LT560C, 32/37/42/47LT560E) AV IN DC IN VIDEO RGB IN (PC) 1 2 R / DVI IN L EXTERNAL SPEAKER OUT L/MONO -AUDIO- R RS-232C IN (CONTROL & SERVICE) ANTENNA/ CABLE IN RJP INTERFACE AUDIO IN (RGB/DVI) LL+ R+ R- 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV.
ASSEMBLING AND PREPARING 21 Tidying cables For 32/37/42LT560C, 32/37/42/47LT560E 1 Install the power cord holder and power cord. It will help prevent the power cable from being removed by accident. For 55LS460E 1 Gather and bind the cables with the cable holder. Cable Holder Power Cord Holder 2 Gather and bind the cables with the cable holder. Caution Cable Holder For 22/26LT560C 1 Gather and bind the cables with the cable holder.
ASSEMBLING AND PREPARING Making Connections Image shown may differ from your TV. yy Connect the external devices.
REMOTE CONTROL 23 REMOTE CONTROL Below is a description of the remote control. Your remote control may look slightly different. To install batteries, open the battery cover, insert batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION Do not mix old and new batteries, as this may damage the remote control. yy This remote uses infrared light.
REMOTE CONTROL PORTAL Displays and removes the interactive menu. (For LT560C series) Displays the EzSign content on a TV Screen. (For LT560E, LS460E series Q.MENU INPUT TV 1 4 7 DVD .,;@ ghi pqrs 2 5 8 INFO Views the information of the current program and screen. (For LT560C series) Shows or hides the information on TV remote control buttons in EzSign mode. (For LT560E, LS460E series) MARK abc jkl tuv 0 3 6 9 def GUIDE Displays and removes the electronic program guide.
GENERAL TROUBLESHOOTING / CAUTION FOR USING EzSign 2.0 25 GENERAL TROUBLESHOOTING Display Panel Picture Symptom No picture. Possible Cause(s) Display panel is turned off. yy Antenna/cable not connected. yy Connections incorrect. yy MPI not connected yy Encrypted program. yy Wrong tuning band. yy Possible Solution(s) Turn TV ON. yy Power failure? yy Connect antenna/cable signal to TV. yy Check connections on TV. yy If applicable, connect MPI cable to MPI device. yy Try another channel.
SPECIFICATIONS SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions.
SPECIFICATIONS 42LT560C (42LT560C-UA) MODELS Dimensions (W x H x D) 47LT560E (47LT560E-UA) 42LT560E (42LT560E-UA) With stand 991.7 x 666.5 x 273.1 (mm) Without stand 991.7 x 604.0 x 55.0 (mm) 1,101.0 x 728.5 x 273.1 (mm) 39.0 x 26.2 x 10.7 (inch) Weight 43.3 x 26.1 x 2.1 (inch) With stand 15.5 kg (34.1 lbs) 17.3 kg (38.1 lbs) Without stand 13.5 kg (29.7 lbs) 15.3 kg (33.7 lbs) 1.0 A / 100 W 1.
IR CODES IR CODES (Depending on model) Code (Hexa) Function 08 (POWER) Note Remote control Button (Power On/Off) ENGLISH ENG 0B INPUT Remote control Button 10-19 Number Key 0-9 Remote control Button 4C - (DASH) Remote control Button 1A FLASHBK Remote control Button 02 VOL + Remote control Button 03 VOL - Remote control Button 09 MUTE / DELETE Remote control Button 00 CH ^ / PAGE ^ Remote control Button 01 CH v / PAGE v Remote control Button 43 SETTINGS / MENU Remote
EXTERNAL CONTROL DEVICE SETUP 29 EXTERNAL CONTROL DEVICE SETUP RS-232C Setup Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Type of connector; D-Sub 9-Pin Male 1 5 6 9 RS-232C IN (CONTROL & SERVICE) RS-232C IN (CONTROL & SERVICE) No.
EXTERNAL CONTROL DEVICE SETUP RS-232C configurations Set ID Set ID number. 7-Wire Configuration (Serial female-female NULL modem cable) OPTION 2 3 TXD TXD 3 2 RXD GND 5 5 GND DTR 4 6 DSR DSR 6 4 DTR RTS 7 8 CTS CTS 8 7 RTS D-Sub 9 : On • My Media Setting • Set ID :1 • Mode Setting : Home Use ꔉ 1 Press Home or MENU to access the main menus. 2 Press the Navigation buttons to scroll to 3 Press the Navigation buttons to scroll to Set ID and press OK/ENTER.
EXTERNAL CONTROL DEVICE SETUP 31 Communication Parameters Stop bit: 1 bit yy Communication code: ASCII code yy Use a crossed (reverse) cable. yy Baud rate: 9600 bps (UART) yy Data length: 8 bits yy Parity : None yy Command reference list 01. Power COMMAND1 COMMAND2 DATA (Hexadecimal) k a 00 - 01 COMMAND1 COMMAND2 DATA (Hexadecimal) 14. Treble k r 00 - 64 b (See p.33) 15. Bass k s 00 - 64 k c (See p.33) 16. Balance k t 00 - 64 04. Screen Mute k d 00 - 01 17.
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the set.(j, k, m or x) [Command 2] : Second command to control the set. [Set ID] : You can adjust the set ID to choose desired set ID number in Option menu. Adjustment range is 1~ 99. When selecting Set ID ‘0’, every connected the set is controlled.
EXTERNAL CONTROL DEVICE SETUP 01. Power (Command: k a) To control Power On/Off of the set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 00: Power Off Data 01: Power On Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x] * In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function. * Note: In this model, set will send the Acknowledge after power on processing completion.
EXTERNAL CONTROL DEVICE SETUP 12. OSD Select (Command: k l) To select OSD (On Screen Display) on/off. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 00: OSD off Data 01: OSD on Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x] 13. Remote Control Lock Mode (Command: k m) To lock the remote control and the front panel controls on the set.
EXTERNAL CONTROL DEVICE SETUP 20. Energy Saving (Command: j q) To control the energy saving function. Transmission [ j ][q][ ][Set ID][ ][Data][Cr] Data 00: off 01: Minimum 02: Medium 03: Maximum 04: Auto/Intelligent sensor (depending on model) 05: Screen off Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x] 21. Auto Configuration (Command: j u) To adjust picture position and minimize image shaking automatically. Auto configuration only works in RGB-PC mode.
EXTERNAL CONTROL DEVICE SETUP * Table List (Channel Tuning) 7 Main/Sub Picture 6 Two/One Part Channel 5 Using Physical Channel 4 Reserved 3 2 1 0 Step 0 Main 0 Two 0 Use x 0 0 0 0 NTSC Air 1 Sub 1 One 1 No Use x 0 0 0 1 NTSC Cable x 0 0 1 0 ATSC Air x 0 0 1 1 ATSC Cable_std x 0 1 0 0 ATSC Cable_hrc x 0 1 0 1 ATSC Cable_irc x 0 1 1 0 ATSC cable_auto x 0 1 1 1 Reserved x x x x x ...
CHILD SAFETY: It Makes A Difference How and Where You Use Your Flat Panel Display Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind: THE ISSUE yy The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases. However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations.
The model and serial numbers of the TV are located on the back and/or one side of the TV. Record them below should you ever need service. MODEL SERIAL LG Customer Information Center For inquires or comments, visit www.lg.com or call: 1-888-865-3026 1-888-542-2623 USA, Commercial User CANADA (For 22/26LT560C) This product qualifies for ENERGY STAR in the Pro:Centric is a trademark of LG Electronics U.S.A., Inc.(For LT560C series) “factory default (Home Use)” setting.
