LCD TV OWNER'S MANUAL MODELS: 23LC1R * Please read Information Manual included together before reading this manual and operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote require service.
Contents Installation 3 Location and function of controls Remote control handset Battery installation / Front/ Rear 6 Basic operation On and off / Programme selection Volume adjustment / Quick view Mute function On screen language selection 10 On 11 screen menus Menu selection 12 up TV stations Auto programme tuning Manual programme tuning Assigning a station name Programme edit Favourite programme Calling the programme table Setting Picture adjustment PSM (Picture Status Picture adjustment Pic
Installation Unfolding ENGLISH the stand base 1. Place the set with its front facing downward on a cushion 2. Hold down the release button inside the stand and or soft cloth. strongly pull out the stand with your two hands. Note: Here shown may be somewhat different from your set. The stand won't move if you don't press release button.
Installation Desktop Pedestal Installation 4 inches 4 inches 4 inches 4 inches For proper ventilation, allow the wall. a clearance of 4" on each side and from Connection of TV 1. Connect the aerial cable to the socket marked +75 Ω on the back. For the best reception an outdoor aerial should be used. 2. To connect an additional equipment, see the Connection of external 3. Connect the power cord. Note: Here shown may be somewhat different from your set. ( 4 ) equipment section.
Installation ENGLISH Positioning your display Adjust ? the position of the panel in various ways for maximum comfort. Tilt range 12 Be careful that your hands down when tilting the pressed are not screen. Location Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air.
Location and function of controls All the functions can be controlled with the remote control handset. Some functions can also be panel of the set. operate this Only adjusted with the buttons the remote control handset on supplied the top will set. Remote control handset 10 MUTE POWER 1 11 TV INPUT I/II Before you use the remote control handset, batteries. See the next page. 1. 12 2 LIST MUTE switches the sound 13 2. off. TV returns to the TV mode.
Location and function of controls 11. POWER switches the set 12. I/II selects the on from standby language during dual or off to ENGLISH standby. language broadcast. 13. MENU selects a menu. 10 MUTE 14. PSM (Picture Status recalls your preferred Memory) picture setting. POWER 1 11 TV INPUT I/II 12 2 15. TELETEXT BUTTONS These buttons are used for teletext. For further details, see the 'Teletext' section. LIST Q.
Location and function of controls Front Top panel PR VOL OK MENU INPUT /I 7 6 5 432 1 8 1. ON/OFF( 6. /I) switches the set on from standby or INPUT selects the remote switches the set 3. operating from standby. OK or displays mode. 5. 8 / REMOTE CONTROL SENSOR 8. POWER/STANDBY INDICATOR illuminates orange in standby mode. illuminates blue when the set is switched a menu. accepts your selection 7. mode. MENU selects 4.
Location and function of controls ENGLISH Rear COMPONENT VIDEO COMPONENT (VIDEO / AUDIO Input) L AUDIO R PC SOUND PC INPUT JACK PC INPUT ANTENNA INPUT INPUT ANTIN( 75 ) PC SOUND AV1 H/P AC IN AV2 AC INPUT EURO SCART AUDIO/VIDEO SOCKET INPUT S-VIDEO S-VIDEO INPUT HEADPHONE JACK 9
Basic operation On and off 1. Press the switch it 2. 3. POWER : If, while the INPUT , TV, INPUT or NUMBER buttons to set is switched on, the mains the set will switch to replaced TV / fully. Press the POWER button. The set reverts to Pull out mains plugs to switch the set off. Note MUTE POWER, on standby or power in the mains power socket. on standby plug mode. is disconnected when the mains plug is I/II Programme selection You a Q.
On ENGLISH screen menus Menu selection 1. 2. Press the MENU button and then Press the button and then / / button to display each menu. button to select a menu item. the setting of an item in the sub or pull-down menu with button. / You can move to the higher level menu by pressing the OK button and to move to the lower level menu by pressing the MENU button. Note : a. In the TV, AV, S-video or COMPONENT mode, the PC menu is 3. Change not b. displayed.
Setting up Channel TV stations Up to 100 TV stations can be stored by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the / or NUMBER buttons to scan the stations you have programmed. Stations can be tuned using automatic or manual modes. Auto programme Manual programme Programme edit Favourite programme Auto programme DEFG OK tuning All stations that can be received are stored by this method.
Setting up Manual programme TV stations tuning Auto programme Manual programme Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can assign a station name with five characters to each programme number. 1. Press the MENU button and then Channel menu. 2. Press the 3. programme.
Setting up Assigning a station name 1. Repeat the 'Manual programme tuning' steps Channel Auto programme Manual programme Programme TV stations 2. edit Favourite programme 3. Press the button and then / Press the button and then use 1 to 2. button to select Name. the / . You can use a 4. -,thenumber0to9andthealphabetAtoZ. button you can select in the opposite direction. Select the position by pressing the button and then / 5.
Setting up Programme TV stations Auto programme Manual programme This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or insert a blank station data into the selected programme number. 1. Press the MENU button and then Channel 2. Programme edit Favourite programme button to select the / menu. Press the ENGLISH Channel edit DEFG button and then button to select / OK MENU Programme edit. 3.
Setting up TV stations Favourite programme Channel Auto programme This function lets you select your favourite programmes Manual programme Programme edit Favourite programme 1. Press the MENU button and then Channel menu. 2. Press the button and then / directly. button to select the to select Favourite / programme. DEFG OK MENU Favourite programme On -- ----- -- ----- -- ----- -- ----- -- ----- -- ----- -- ----- -- ----- DEFG 3. TV 4. 5. LIST Q.VIEW MENU 6. 7.
Picture PSM adjustment (Picture Status Memory) ENGLISH Picture PSM 1. Press the MENU button and then Picture Press the 3. Press the ting on Contrast Brightness menu. 2. 4. button to select the / button and then button and then the PSM Colour button to select PSM. / button to select / a picture Sharpness set- menu. Press the OK button. DEFG OK MENU Picture PSM Dynamic Contrast Standard Brightness Mild Colour Game Sharpness User DEFG 5.
Picture adjustment Picture format You watch TV in various can picture formats; 16:9, 14:9, Zoom, Auto, 4:3. Repeatedly press the ARC button to select your desired picture for- mat. 16:9 You can enjoy the cinema (the picture format of 16:9) or general TV programme through the 16:9 mode. The screen 16:9 is viewed just like that but the screen 4:3 is magnified to the left and right so that the screen 16:9 is full.
Sound SSM You ENGLISH Sound (Sound Status Memory) SSM select your preferred sound setting; Flat, Music, Movie or and you can also adjust the sound frequency of the equalizer. can Speech 1. adjustment Press the MENU button and then Sound menu. AVL Balance button to select the / Sound DEFG SSM Flat AVL Music Balance Movie OK MENU Speech G User DEFG 2. 3. Press the Press the setting on Sound OK MENU button and then button and then the SSM menu. button to select SSM.
Sound adjustment Stereo/Dual When reception programme is selected, the sound information for the station appears after the programme number and station name a disappear. I/II Broadcast On Screen Mono MONO Stereo STEREO Dual DUAL I Display Mono sound selection In stereo reception if the stereo signal is weak, you can switch to mono by pressing the I/II button twice. In mono reception the depth of sound is improved. To switch back to stereo, press the I/II button twice again.
TIME Menu Clock ENGLISH Time Time You must set the time 1. using Press the MENU button and then TIME 2. before correctly Off time on/off time function. / On time Auto off button to select the menu. Press the button and then button to select TIME. / Time DEFG OK MENU -i-i:i-i- Time Off time On time Auto off DEFG OK MENU 3. Press the button and then 4. Press the button and then 5. Press the MENU button to button to / button to / adjust the hour. adjust the minute.
TIME Menu Auto off Time Time Off time If you select On on the Auto off menu, the set will automatically switch itself to standby mode approximately ten minutes after a TV On time Auto off station DEFG 1. OK MENU stops broadcasting. Press the MENU button and then TIME / button to select the menu. 2. Press the button and then / button to select Auto off. 3. Press the button and then / button to select On or Off. Time Time Off time On time On Auto off Off DEFG MENU 4.
Other functions TV, AV and PC modes ENGLISH Setup Language Input be set for TV, AV or PC mode. AV mode is used when a Inputs video cassette recorder (VCR), or other equipment is connected to can Child lock Power indicator the set. Note : When a VCR is connected via the aerial socket the set is used in TV mode. See the 'Connection of external equipment' section. 1. Press the MENU button and then Setup / DEFG OK MENU button to select the menu. 2. Press the 3.
Other functions Setup Child lock Language Input Child lock The TV Power indicator control it. This feature can be set that the remote control handset is needed to so can be used to prevent unauthorized view- ing. DEFG OK 1. MENU Press the MENU button and then Setup 2. Press the button and then 3. Press the button and then on / button to select the menu. the Child lock button to select Child lock. / button to select On / or Off menu.
Teletext - ENGLISH This feature is not available in all countries. Teletext (or TOP text) is an optional function, therefore only with the teletext system can receive the teletext broadcast. Teletext is a free service broadcast by most TV stations which up-to-the-minute information on news, weather, television programmes, share prices and many other topics. a set gives The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems.
Teletext Direct page selection Corresponding to the SIMPLE teletext mode, you ber using the NUMBER buttons in TOP mode. can select a page by entering it as a three digit num- FASTEXT The teletext pages are colour coded corresponding coloured button. along the bottom of the selection Press the i button to select the index page. You can select the pages which are colour coded screen and are selected by pressing the Page 1. 2. along the bottom line with the same coloured but- tons.
Connection of external You connect additional equipment, such as etc. to your set. Examples are shown as below. can equipment ENGLISH VCRs, camcorders Aerial socket PC INPUT 1. 2. 3. 4. 5. Connect the RF out socket of the VCR to the aerial socket of the set. Connect the aerial cable to the RF aerial in socket of the VCR. Store the VCR channel on a desired programme number using the 'Manual programme tuning' section. Select the programme number where the VCR channel is stored.
Connection of external Euro scart socket PC INPUT (DVD) ANT IN AV1 1. S-V AV2 2. 3. DVD Connect the Euro scart socket of the DVD to the Euro scart socket of the set. Press the INPUT button to select AV1. Press the PLAY button on the DVD. The DVD playback picture appears on the DVD COMPONENT 1. VIDEO input screen. sockets Connect the DVD output sockets (Y Cb Cr, Y Pb Pr, Y B-Y R-Y Y PB PR) of the DVD to the COMPONENT/VIDEO sockets (Y or PB L AUDIO equipment R DVD PR) of the set. 2.
Connection of PC ENGLISH PC in socket 1. 2. 3. 4. Connect the signal cable from the monitor output socket of the PERSONAL COMPUTER to the PC input socket of the set. Connect the audio cable from the PC to the PC SOUND sockets of the set. Press the INPUT button to select PC. Switch on the PC, and the PC screen appears on the set. The set can be operated as the PC monitor.
Connection of PC PC PC Setup You can H-Position V-Position adjust horizontal/vertical position, clock, phase, configure, reset as you prefer. Clock Phase Auto Configure Reset DEFG OK and auto- 1. Press the MENU button and then Setup MENU button to select the / menu. 2. Press the button and then button to select 3. Press the button and then button to select PC. 4. / / Press the MENU button and then / Input. button to select the PC menu.
T roubleshooting Checklist Checklist The ? doesn't work Power is suddenly Check to control The remote control does not work operation see if there is any obstruction. object normally. between the product Are batteries installed with correct ? Correct remote ? Install new ? Is the sleep ? Check the power control settings. Power interrupted No broadcast on station tuned with Auto off activated.
The audio function does not work. No ? Press the VOL Picture OK & ? Sound muted? Press MUTE button. No sound ? Try ? Are the audio cables installed ? Adjust ? A output from of the one another channel. The Balance in problem may be properly? with the broadcast. option. menu speakers Unusual sound from inside the change in ambient noise when the product the humidity or temperature may result in an unusual product is turned on or off and does not indicate a fault with product.