Owner's Manual
APPENDIX
81
20.
Abnormal
State
(Command2:z)
To
recognize
an
abnormal
state.
This
feature
is
not
available for
all
models.
Data
FF:
Read
Data
0:
Normal
(Power
on
and
signal
exist)
Data
1:
No
signal
(Power
on)
Data
2:
Turn
the
TV
off
by
remote
control
Data
3:
Turn
the
TV
off
by
sleep
time
function
Data
4:
Turn
the
TV
off
by
RS-232C
function
Data
5:
5V
down
Data
6:
AC
down
Data
7:
Turn
the
TV
off
by
Fan
Alarm
function
(option)
Data
8:
Turn
the
TV
off
by
Off
time
function
Data
9:
Turn
the
TV
off
by
Auto
sleep
function
*
This function
is
"read
only".
Transmission
[k][z][
][Set
ID][
][FF][
][Cr]
Acknowledgement
[z][
][Set
ID][
][OK][Data][x]
21.
ISM
Method
(Command1:j,
Command2:p)
To
control
the
ISM
method.
You
can
also
adjust
ISM
Method
in
SPECIAL
menu.
This
feature
is
not
available for
all
models.
Data
0:
Normal
Mode
Data
1:
White
Wash
Data2:
Orbiter
Data3:
Inversion
Transmission
[j][p][
][Set
ID][
][Data][Cr]
Acknowledgement
[p][
][Set
ID][
][OK][Data][x]
22.
Low
Power
(Command1:j,
Command2:q)
To
reduce
the
power
consumption
of
the
monitor.
You
can
also
adjust
Low
Power
in
SPECIAL
menu.
This
feature
is
not
available for
all
models.
Data
0:
Off
Data
1:
On
Transmission
[j][q][
][Set
ID][
][Data][
][Cr]
Acknowledgement
[q][
][Set
ID][
][OK][Data][x]
23.
Orbiter
Time
Setting
(Command1:j,
Command2:r)
To
adjust
orbiter
operation
time
term.
This
feature
is
not
available for
all
models.
Data
Min:
1
~
Max:
FE
Refer
to
'Real
data
mapping
1'.
Transmission
[j][r][
][Set
ID][
][Data][
][Cr]
Acknowledgement
[r][
][Set
ID][
][OK][Data][x]
24
.
Orbiter
Pix
el
Setting
(Command1:j,
Command2:s)
To
adjust
pixel
number
in
orbiter
function.
This
feature
is
not
available
for
all
models.
DataMin:1~Max:3
Refer
to
'Real
data
mapping
1'.
Transmission
[j][s][
][Set
ID][
][Data][Cr]
Acknowledgement
[r][
][Set
ID][
][OK][Data][x]
25
.
Auto
Configure
(Command1:j,
Command2:u)
To
adjust
picture
position
and
minimize
image
shaking
automatically.
It
works
only
in
RGB
(PC)
mode.
Data
1:
To
set
Transmission
[j][u][
][Set
ID][
][Data][Cr]
Acknowledgement
[u][
][Set
ID][
][OK][Data][x]
26
.
Programme
selection
(Command1m,
Command2:a)
To
select
a
programme
for
the
main
picture.
Data0:
Min:0~Max:63(0~C7,200Prison)
Refer
to
'Real
data
mapping
1'.
Data
1:
Don't
care
Data2:
0:Main
1
:
Sub
(option)
Transmission
[m][a][
][Set
ID][
][Data0][
][Data1]
[
][Data2][Cr]
Acknowledgement
[a][
][Set
ID][
][OK][Data0][x]
Real
data
mapping
1
0:Step0
A
:
Step10(SetID10)
F
:
Step15(SetID15)
10:
Step16(SetID16)
64
:
Step
100
6E
:
Step
110
73
:
Step
115
74
:
Step
116
C7
:
Step
199
FE
:
Step
254
FF
:
Step
255
Real
data
mapping
2
0:-
3
0
1:-
2
9
2:-
2
8
1E:0
3A:+28
3B:+29
3C:+30
0323G_3-en_rev02
3/22/06
1:33
AM
Page
81