Installation Manual
42
206-4298
Installer Menu (Cont.)
020 - FEATURE LEVEL
Determines an additional IR code scheme to which the TV will
respond, allowing for the use of unique IR codes based on “bed
number” in a multi-TV single room installation. First determine the
IR mode; then select the bed number.
Note: When item 027 HOSPITAL MODE is set to 0, both the
IR code that will control the TV and the speaker selection are
determined by this item (default = 1). Set this item as required to
enable Zenith Bed 1 or Bed 2 IR codes and speaker selections.
Values IR Mode Bed # Speaker
0 – 1 Zenith (Hospital) 1 – 2 TV Only
16 – 24 Multi-code Remote 1 – 9 TV Only
64 – 65 Zenith (Hospital) 1 – 2 Pillow Only
Note: See Reference section, “LG Pro:Centric Patient Remote
and Pillow Speaker,” for additional information. Also, see
documentation for the accessory package that includes the multi-
code remote.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control) and have it available
to the end user to lter and control or otherwise restrict program-
ming content that can appear. Set to 0 to turn the V-Chip feature
Off (not available to user); no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
Note: This item is not available in the Installer Menu when item 021
V-CHIP is set to 0 or when item 084 PERMANENT BLK is set to 1.
023 - CAPTION LOCK
If set to 0, captions are OFF when the TV is turned ON. Set to 1
to use the caption setting congured before the TV was turned
OFF when the TV is turned ON.
025 - FUNCTION PRE (Function Preview)
Set to 1 to allow access to the Channel Preview/Banks Setup
Menu via the CH PREVIEW key on Installer Remote. Set to 0 to
disable access to the Channel Preview/Banks Setup Menu.
Note: This item is only applicable when the TV is in PTC-CTV
Mode.
027 - HOSPITAL MODE
Set according to the speaker selection, the pillow speaker code/
supply voltage and the hospital IR code. If using a Pro:Centric
pillow speaker, select one of the Zenith codes in accordance with
the desired speaker selection. See table below.
When Hospital Mode is enabled, channel banks are also avail-
able. Refer to “Channel Banks Overview” on page 30 for further
information. Channel banks are not supported if Hospital Mode is
set to 0.
Value Speaker
Pillow Speaker
Code/Voltage
Hospital IR Code
000 Determined by
item 020 setting
Zenith (+12v) Determined by item
020 setting
001 Pillow Only Zenith (+12v) Zenith Bed #1
002 Pillow Only Zenith (+12v) Zenith Bed #2
017 Pillow Only Philips (+5v) Zenith Bed #1
018 Pillow Only Philips (+5v) Zenith Bed #2
033 Pillow Only RCA (-5v) Zenith Bed #1
034 Pillow Only RCA (-5v) Zenith Bed #2
065 TV Only Zenith (+12v) Zenith Bed #1
066 TV Only Zenith (+12v) Zenith Bed #2
081 TV Only Philips (+5v) Zenith Bed #1
082 TV Only Philips (+5v) Zenith Bed #2
097 TV Only RCA (-5v) Zenith Bed #1
098 TV Only RCA (-5v) Zenith Bed #2
129 Both Pillow & TV Zenith (+12v) Zenith Bed #1
130 Both Pillow & TV Zenith (+12v) Zenith Bed #2
145 Both Pillow & TV Philips (+5v) Zenith Bed #1
146 Both Pillow & TV Philips (+5v) Zenith Bed #2
161 Both Pillow & TV RCA (-5v) Zenith Bed #1
162 Both Pillow & TV RCA (-5v) Zenith Bed #2
254 TV Only Disabled (0v) Zenith Bed #2
When Hospital Mode is set to 0 (disabled), both the IR code
that will control the TV and the speaker selection depend on the
Installer Menu item 020 FEATURE LEVEL setting.
Note: The default setting (254) is not selectable in the Installer
Menu. If you ever need to restore the default setting, you must
reload the factory default settings. See item 117 description and/or
Reference section, “Restoring Factory Defaults on the TV(s),” for
further information.
Note: In the Installer Menu, an informational code is displayed
at the right of each Hospital Mode value. Each code consists of
three characters. The rst character—T, P, or B—identies the
speaker: TV, Pillow, or Both. The second character—Z, P, R,
or D—identies the pillow speaker code: Zenith, Philips, RCA, or
Disabled. The third character—1 or 2—identies the bed number.
In the table above, each bolded character represents an element of
the Hospital Mode code.
028 - CH. OVERIDE (Channel Override)
This item either allows or restricts tuning of channels that are NOT
in the PTC Channel Map. If set to 1, end users can tune channels
that are not in the PTC Channel Map by direct keypad entry. If
set to 0, users are restricted to only the channels that are in the
PTC Channel Map. In the case of CPU-CTV Mode, there are no
channels in the PTC Channel Map; therefore, direct keypad entry
is not available. Also, when this item is set to 0, the PTC Channel
Map (PTC-CTV Mode)/CPU channel lineup (CPU-CTV Mode)
is locked, and user access to channel settings in the TV setup
menus is restricted.
Note: This item is not applicable when the TV is in FTG Mode.