Installation Manual

43
206-4298
029 - OLD OCV (On Command Video™)
Set to 1 to remap the PTC’s direct tune channels for Aux inputs
from 13x to 9x. This allows 2-digit only tuning systems (i.e., legacy
OCV) to direct tune Aux inputs. See also Reference section, “TV
Aux Input Conguration.”
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables ACK
feature of MPI.
031 - POLL RATE
MPI Communication Parameter. Selects poll rate for MPI. Step size
of 16 ms. Changing from default may affect communication via MPI.
032 - TIMING PULSE
MPI Communication Parameter. Sets baud rate for MPI. Step size
of 4.3 uS. Changing from default may affect communication via MPI.
035 - HDMI1 ENABLE
Set to 1 to enable display panel HDMI 1 input. Set to 0 to disable
display panel HDMI 1 input.
Note: These models do not support typical PC screen resolutions
(e.g., 1360 x 768). When connecting a PC, set its screen resolution
to 1920 x 1080. You may also need to adjust the TV’s aspect
ratio in order to view the entire PC image. In case of the latter, set
Installer Menu item 096 DEF. ASP. RATIO to 3 (Just Scan).
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (AV) input. Set to 0 to
disable display panel rear Aux (AV) input.
041 - SIMPLINK EN
Set to 0 to disable the SIMPLINK feature. Set to 1 to enable
SIMPLINK functionality (does not enable remote control access to
the SIMPLINK Menu).
Note: When both this item and item 042 AUTO INPUTS are
enabled in the Installer Menu, HDMI inputs will be detected by
SIMPLINK, but the Auto Input(s) Sensing Feature will not function.
042 - AUTO INPUTS
Determines the Aux inputs for which auto-sensing is enabled. Set
to 0 to disable auto-sensing for all available inputs. Set to 255 to
enable auto-sensing for all available inputs. For information on
options for individual input settings, see Reference section, “Auto
Input(s) Sensing Feature.”
Note: In order for auto-sensing to be enabled for an input, that
input must also be enabled in the Installer Menu. For example, to
enable auto-sensing for HDMI 1, item 035 HDMI1 ENABLE must
also be set to 1. Also, see note above regarding TV operation
when both this item and item 041 SIMPLINK EN are enabled.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting Aux source. When turned ON, the TV will tune to
starting Aux source if item 004 STRT CHANNEL is set to 0.
1 = AV 5 = HDMI 2
3 = HDMI 1 255 = Last Aux
Note: Above is applicable only if all Aux sources are enabled.
Note: This item is not available in the Installer Menu unless item
004 STRT CHANNEL is set to 0.
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number
instead of channel 0. Set to 0 to disable Aux identication change.
Controls MPI status channel response for Aux inputs.
049 - DIS. AUDIO M. (Disable Audio Menu)
Determines the availability of the Sound Out (Audio) Menu in the
TV menus. Also determines the default Audio Mode when TV is
turned ON. See the table below and set as required.
Value
Sound Out
Menu Status
Default Audio Mode at TV
Turn ON
0 (default) Enabled Internal TV Speaker
1 Disabled Internal TV Speaker
2 Enabled External Speaker (optical or HDMI)
3 Disabled External Speaker (optical or HDMI)
4 Enabled LG Sound Sync (optical)
5 Disabled LG Sound Sync (optical)
6 Enabled LG Sound Sync (BT wireless)
7 Disabled LG Sound Sync (BT wireless)
8 Enabled Internal TV Speaker + Audio Out (optical)
9 Disabled Internal TV Speaker + Audio Out (optical)
Note: If a SIMPLINK-enabled device is connected to the TV
and item 041 SIMPLINK EN is set to 1 (enabled), the SIMPLINK
device Audio Mode will have priority over the setting of this item
when the TV is turned ON.
Note: Items 020 FEATURE LEVEL and 027 HOSPITAL MODE
have priority over the setting of this item. Thus, if either item 020 or
027 is set to a Pillow Only value and this item is set to an internal
TV speaker value, the pillow speaker setting will have priority, and
you will not be able to hear sound from the TV speaker. You may
however, set an external speaker conguration in conjunction with
the pillow speaker.
Note: When this item is set to 6 or 7, the Bluetooth Sound Sync
Media Share feature is not available. If Bluetooth Sound Sync is
currently enabled in the IP Environment / Media Share Menu, it
will be disabled.
053 - DIS. CH-TIME (Disable Channel-Time Display)
Set to 1 to disable the TV’s native Channel-Time display when a
custom channel label/channel information will be provided by the
MPI command. Set to 0 to enable the TV’s native Channel-Time
display.
Installer Menu (Cont.)