Installation Manual
45
206-4298
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable the SAP feature in the Function Menu, when
the Function Menu is available (i.e., TV is not in Pass-through
Mode). Set to 0 to disable the SAP feature in the Function Menu,
when the Function Menu is available.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up:
0 = Set By Program 1 = 4:3
2 = 16:9 (default) 3 = Just Scan
4 = Zoom
Note: This item is not available in the Installer Menu unless item
106 ASP RATIO LOCK is set to 0.
097 - AUDIO OUTPUT
Determines availability and signal type/level (xed speaker,
variable speaker, or xed line level [amplier]) of the audio output to
be used by external audio equipment connected to the SPEAKER
OUT / LINE OUT jack on the TV. Set to 0 to disable audio output.
Otherwise, see the table below and set as required in accordance
with audio equipment. See also Reference section, “External
Stereo Speaker Specifications.”
Value Status
Speaker Output 1 Fixed 0.01 Watts
2 Fixed 0.03 Watts
3 Fixed 0.05 Watts
4 Fixed 0.10 Watts
5 Fixed 0.20 Watts
6 Fixed 0.50 Watts
7 Fixed 1.00 Watt (default)
8 Control with volume
Line Output 9 Fixed line level (typically 400 mVrms ±
100 mVrms @10KΩ) output
098 - PRO:CENTRIC
Selects the Pro:Centric Application Mode. Set to 0 (default) to
disable the Pro:Centric application. Set to 1 for Flash Mode. Set
to 2 for GEM (Java Application) Mode. Set to 3 for HTML Mode.
In order to retrieve the Pro:Centric application, when enabled (for
Flash or GEM Mode), the TV must be turned OFF/ON two times.
Once you exit the Installer Menu, turn OFF the TV for at least one
minute. When you turn the TV back ON, the TV will start the
appropriate library based on the setting of this item. Wait until TV
programming appears on the display, and then turn the TV back
OFF, this time for a few minutes, to initiate the application down-
load. When you turn the TV back ON, press the PORTAL key on
the Installer Remote, and verify that the Pro:Centric application
appears on the display.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 255.
• 1 - 100 Static Back Lighting
(1 = Dimmest picture, 100 = Brightest picture)
• 101 - 200 Dynamic Back Lighting
(101 = Dimmest picture, 200 = Brightest picture)
If set between 101 and 200, the TV automatically controls back
lighting depending upon the picture level of the current program. If
set to 255, back lighting is controlled via the Picture settings in the
TV setup menus.
101 - IR FEEDBACK
If set to 0 (default), the TV’s MMR (Magic Motion Remote) feature
is enabled, and a compatible LG MMR (not supplied) may be used
with the TV. If set to 2, the MMR feature is disabled.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0 = Broadcast 1 = CATV 2 = HRC
3 = IRC 4 = Same as NTSC
103 - ATSC TUNE MODE
Sets ATSC tuning mode. Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
104 - START MINOR CHANNEL
Sets Minor Start Channel number at power up. 0 = NTSC. If not 0,
number selected is the digital channel’s Minor Start Channel number.
Note: This item is not available in the Installer Menu when item
004 STRT CHANNEL is set to 0 or 255.
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power off. Set to 0 to
retain default aspect ratio with power off. See item 096 DEF. ASP.
RATIO above.
107 - BANNER SELECT
Selects the type of banner to display during channel change. Set to
1 for channel label display, plus channel information (full banner).
Set to 0 for channel label display only (small banner).
116 - VIDEO MUTE EN (Video Mute Enable)
Applicable for analog channels only. If set to 1, video mutes
(blank screen) when no signal is present.
117 - FACT DEFAULT (Factory Default)
Set to 1 and press OK to restore the factory default settings of all
Installer Menu items. Once complete, the value returns to 0.
Caution: If set to 1, this clears all Installer Menu custom
settings and restores the factory default settings. It
also clears the channel lineup, including any assigned
channel icons and custom text labels.
Note: See also Reference section, “Restoring Factory Defaults on
the TV(s),” for further information.
Installer Menu (Cont.)