Owner's Manual
Table Of Contents
- Preparation
- External equipment setup
- Antenna Connection
- Connecting with a Component cable
- Connecting with an HDMI cable
- Connecting with an HDMI to DVI cable
- Connecting with a Euro Scart cable
- Usb setup
- Connecting with a RF Cable
- Connecting with a RCA cable
- Connecting with a D-sub 15 pin cable
- Insertion of CI Module
- Headphone Setup
- Digital audio out Setup
- External Equipment WIreless Connection
- Supported Display Resolution
- Screen Setup for PC mode
- Watching TV / Programme control
- Turning on the TV
- Initializing Setup
- Programme Selection
- Volume Adjustment
- Quick Menu
- On Screen Menus Selection and adjustment
- Auto programme tuning
- Cable DTV setting
- Manual programme Tuning
- Programme Edit
- CI [Common Interface] Information
- Software Update
- Picture/Sound test
- Diagnostics
- Product/service information
- Simple Manual
- Selecting the Programme List
- Input List
- Input Label
- Data Service
- SIMPLINK
- AV Mode
- Initializing(Reset to original factory settings)
- To use a USB device
- EPG(Electronic programme guide)(in digital mode)
- Picture Control
- Sound & Language control
- Auto Volume Leveler
- Clear Voice II
- Preset Sound Settings-Sound Mode
- Sound Setting Adjustment -User Mode
- Infinite Sound
- Balance
- TV Speakers On/ Off Setup
- DTV Audio Setting (in digital mode only)
- Selecting Digital Audio out
- Audio Reset
- Audio Description (In digital mode only)
- I/II
- On-Screen Menu Language / Country Selection
- Language Selection
- Time Setting
- Parental Control / Ratings
- Teletext
- Digital Teletext
- Appendix
151
APPENDIX
Communication Parameters
■ Baud rate : 9600 bps
(
UART
)
■ Data length : 8 bits
■ Parity : None
■ Stop bit : 1 bit
■ Communication code : ASCII code
■ Use a crossed (reverse) cable.
Transmission
*
[Command 1] : First command to control the TV.
(j, k, m or x)
*
[Command 2] : Second command to control the TV.
*
[Set ID] : You can adjust the set ID to choose
desired monitor ID number in option
menu. Adjustment range is 1 to 99.
When selecting Set ID ‘0’, every con-
nected set is controlled.
Set ID is indicated as decimal (1 to 99)
on menu and as Hexa decimal (0x0 to
0x63) on transmission/receiving proto-
col.
*
[DATA] : To transmit command data.
Transmit ‘FF’ data to read status of com-
mand.
*
[Cr] : Carriage Return
ASCII code ‘0x0D’
*
[ ] : ASCII code ‘space (0x20)’
[Command1][Command2][ ][Set ID][ ][Data][Cr]
OK Acknowledgement
* The set transmits ACK (acknowledgement) based
on this format when receiving normal data. At this
time, if the data is data read mode, it indicates
present status data. If the data is data write mode,
it returns the data of the PC computer.
[Command2][ ][Set ID][ ][OK][Data][x]
Error Acknowledgement
* The set transmits ACK (acknowledgement) based
on this format when receiving abnormal data from
non-viable functions or communication errors.
[Command2][ ][Set ID][ ][NG][Data][x]
Transmission / Receiving Protocol
Command Reference List
Data 00: Illegal Code
* Note : During USB operations such as DivX or EMF, all
commands except Power(ka) and Key(mc) are not exe-
cuted and treated as NG.
COMMAND
1
COMMAND
2
DATA
(Hexadecimal)
01. Power k a
00
to
01
02. Aspect Ratio k c Refer to p. 152
03. Screen Mute k d Refer to p. 152
04. Volume Mute k e
00
to
01
05. Volume Control k f
00
to
64
06. Contrast k g
00
to
64
07. Brightness k h
00
to
64
08. Colour k i
00
to
64
09. Tint k j
00
to
64
10. Sharpness k k
00
to
64
11. OSD Select k l
00
to
01
12.
Remote control lock mode
k m
00
to
01
13. Treble k r
00
to
64
14.
Bass
k s
00
to
64
15. Balance k t
00
to
64
16.
Colour Temperature
x u
00
to
64
17. Energy Saving j q
00
to
05
18. Auto Configuration j u 01
19. Tune Command m a Refer to p. 154
20. Programme Add/Skip m b
00
to
1
21. Key m c Key Code
22. Control Back Light m g
00
to
64
23. Input select (Main) x b Refer to p. 155