Owner's Manual
Table Of Contents
- COVER
- WARNING / CAUTION
- SAFETY INSTRUCTIONS
- CONTENTS
- FEATURES OF THIS TV
- PREPERATION
- ACCESSORIES
- FRONT PANEL INFORMATION
- BACK PANEL INFORMATION
- STAND INSTRUCTIONS
- CABLE MANAGEMENT
- DESKTOP PEDESTAL INSTALLATION
- SWIVEL STAND
- ATTACHING THE TV TO A DESK
- VESA WALL MOUNTING
- SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND
- ANTENNA OR CABLE CONNECTION
- MPI CARD SLOT / PPV CARD INSTALLATION
- EXTERNAL EQUIPMENT SETUP
- WATCHING TV / CHANNEL CONTROL
- USB
- PICTURE CONTROL
- SOUND & LANGUAGE CONTROL
- TIME SETTING
- PARENTAL CONTROL / RATINGS
- APPENDIX
- COMMERCIAL MODE SETUP GUIDE
- Safety Warnings
- IMPORTANT SAFETY INSTRUCTIONS
- Table of Contents
- Commercial Mode Overview
- Pro:Centric Operation
- Installer Remote Control Typical Key Functions
- Master TV Setup
- Installer Menu
- Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)
- Cloning Overview
- USB Cloning Procedures
- Clone Programmer Cloning Procedures
- FTG Mode of Operation Overview
- FTG Mode via CPU
- FTG Mode via EBL (Local Configuration)
- FTG File Manager Utilities Overview
- IP Environment Setup
- Remote Jack Pack / TV Connections & Setup
- Reference
- Upgrading TV/PTC Software using a USB Memory Device
- Downloading a Splash Screen Image
- Power Consumption Settings
- TV Camport Auto Sense Operation
- TV Aux Input Configuration
- b-LAN Setup & Overview
- RJP Model List and Input Auto-sensing Hierarchy
- Resetting Factory Defaults on the TV(s)
- TV Zone Restrictions
- LD660H/LD665H Rear Jack Panel
- LV555H Rear Jack Panel
- Side Connections Panel
- RF Antenna Connection
- Troubleshooting
- Glossary of Terms
- Document Revision History / Notes
- BACK COVER
24
206-4200
Cloning Overview
IMPORTANT CLONING INFORMATION
Starting with these TV models, there are now four different procedures for cloning a Master TV Setup,
each with its own advantages and limitations (see also “Cloning Methods” on page 11):
• Using a USB memory device / .tlx le
• Using a USB memory device / .tll le
• Using a TLL-1100A clone programmer
• Using a LT2002 clone programmer
Each cloning method is described in further detail on the pages that follow. As you perform cloning proce-
dures, be sure to complete each task as indicated. If a procedure or step is omitted or not performed
completely, cloning may not work. At each step, pay attention to ensure the TV screen shows the proper
message when cloning. If the message indicated does not appear, there is a problem with that step, and
cloning may not be successful.
Caution: Copying a blank or incorrect memory into a TV from a clone programmer will
cause the TV to operate erratically or become inoperable.
Caution: Do not connect a clone programmer to a PPV card installed in the Master or
Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if
you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port.
Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Before you begin cloning:
• Complete the Master TV Setup procedure (see pages 11 to 14).
• All equipment should be connected to power and turned ON.
• Both the Master and Target TVs must be in Pass-through Mode.
• Learning and Teaching is only possible between identical model TVs.
• If using a USB memory device, ensure the USB device has been formatted with FAT format.
• If using a USB memory device / .tlx le, ensure that the Master TV Setup does not contain a Channel Map;
otherwise, Teaching will result in the Target TV(s) being congured for FTG Mode via CPU.
• For both Master and Target TVs—If using a clone programmer, ensure the TV is tuned to either an Aux
input or an analog (not a digital) channel.
• LT2002 only—Make sure the batteries in the clone programmer are fresh. If batteries are removed, the
clone programmer clock time (if set) will be lost (see page 32 for information on the clone programmer
clock).
Caution: Do not unplug the TV power cord or remove/disconnect the USB memory device/
clone programmer while Learning or Teaching, as doing so may cause the TV to malfunction
or harm the USB device/clone programmer, respectively.