Owner's Manual
Table Of Contents
- COVER
- WARNING / CAUTION
- SAFETY INSTRUCTIONS
- CONTENTS
- FEATURES OF THIS TV
- PREPERATION
- ACCESSORIES
- FRONT PANEL INFORMATION
- BACK PANEL INFORMATION
- STAND INSTRUCTIONS
- CABLE MANAGEMENT
- DESKTOP PEDESTAL INSTALLATION
- SWIVEL STAND
- ATTACHING THE TV TO A DESK
- VESA WALL MOUNTING
- SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND
- ANTENNA OR CABLE CONNECTION
- MPI CARD SLOT / PPV CARD INSTALLATION
- EXTERNAL EQUIPMENT SETUP
- WATCHING TV / CHANNEL CONTROL
- USB
- PICTURE CONTROL
- SOUND & LANGUAGE CONTROL
- TIME SETTING
- PARENTAL CONTROL / RATINGS
- APPENDIX
- COMMERCIAL MODE SETUP GUIDE
- Safety Warnings
- IMPORTANT SAFETY INSTRUCTIONS
- Table of Contents
- Commercial Mode Overview
- Pro:Centric Operation
- Installer Remote Control Typical Key Functions
- Master TV Setup
- Installer Menu
- Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)
- Cloning Overview
- USB Cloning Procedures
- Clone Programmer Cloning Procedures
- FTG Mode of Operation Overview
- FTG Mode via CPU
- FTG Mode via EBL (Local Configuration)
- FTG File Manager Utilities Overview
- IP Environment Setup
- Remote Jack Pack / TV Connections & Setup
- Reference
- Upgrading TV/PTC Software using a USB Memory Device
- Downloading a Splash Screen Image
- Power Consumption Settings
- TV Camport Auto Sense Operation
- TV Aux Input Configuration
- b-LAN Setup & Overview
- RJP Model List and Input Auto-sensing Hierarchy
- Resetting Factory Defaults on the TV(s)
- TV Zone Restrictions
- LD660H/LD665H Rear Jack Panel
- LV555H Rear Jack Panel
- Side Connections Panel
- RF Antenna Connection
- Troubleshooting
- Glossary of Terms
- Document Revision History / Notes
- BACK COVER
28
206-4200
Teach To TV (TLL)
xxLD660H-UA00001.TLL
Return Enter
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
Teach To TV (TLX)
Return Enter
Teach To TV
UPDATING...
Do not remove the USB from the port!
Do not unplug!
!
50%
USB Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using a USB Memory Device / .tll File (Cont.)
Teach Master TV Setup to Target TV
1. Ensure the Target TV is in Pass-through Mode, and then use the
Installer Remote to enter the Target TV Installer Menu: Press
MENU repeatedly until the on-screen display of the TV setup
menus no longer toggles, and then press 9-8-7-6 + ENTER.
2. Set Installer Menu item 117 FACT DEFAULT to 001, and press
ENTER. When the value changes back to 0, press ENTER again
to exit the Installer Menu.
3. Tune/set the TV to an analog or digital channel or Aux input, (ideally
the same source tuned for 2-5-5 + MENU Mode during the Master
TV Setup procedure).
4. Plug the USB memory device with the .tll le into the Target TV
USB IN port.
5. Press MENU on the Installer Remote to display the TV setup
menus. Use the arrow navigation keys to select/highlight the
Option menu icon, and then press the number “7” key a total of
seven times to display the USB Download Menu.
6. Use the Up/Down arrow keys to select Teach To TV (TLL), and
then press ENTER.
7. Use the Up/Down arrow keys to select the Master TV Setup you
want to install, and then press ENTER. Note: Filenames identify
the TV and the TLL version (see example at right).
Teaching status will be shown on the progress bar. When the
Teaching process is complete, the USB Download menu will
reappear on screen.
8. When Teaching is done, remove the USB memory device from
the Target TV, turn OFF the TV, and unplug the TV power cord for
15 seconds.
9. Reconnect the TV power cord, and turn ON the TV. The Master
TV Setup should be resident on the Target TV.