Owner's Manual
Table Of Contents
- COVER
- WARNING / CAUTION
- SAFETY INSTRUCTIONS
- CONTENTS
- FEATURES OF THIS TV
- PREPERATION
- ACCESSORIES
- FRONT PANEL INFORMATION
- BACK PANEL INFORMATION
- STAND INSTRUCTIONS
- CABLE MANAGEMENT
- DESKTOP PEDESTAL INSTALLATION
- SWIVEL STAND
- ATTACHING THE TV TO A DESK
- VESA WALL MOUNTING
- SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND
- ANTENNA OR CABLE CONNECTION
- MPI CARD SLOT / PPV CARD INSTALLATION
- EXTERNAL EQUIPMENT SETUP
- WATCHING TV / CHANNEL CONTROL
- USB
- PICTURE CONTROL
- SOUND & LANGUAGE CONTROL
- TIME SETTING
- PARENTAL CONTROL / RATINGS
- APPENDIX
- COMMERCIAL MODE SETUP GUIDE
- Safety Warnings
- IMPORTANT SAFETY INSTRUCTIONS
- Table of Contents
- Commercial Mode Overview
- Pro:Centric Operation
- Installer Remote Control Typical Key Functions
- Master TV Setup
- Installer Menu
- Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)
- Cloning Overview
- USB Cloning Procedures
- Clone Programmer Cloning Procedures
- FTG Mode of Operation Overview
- FTG Mode via CPU
- FTG Mode via EBL (Local Configuration)
- FTG File Manager Utilities Overview
- IP Environment Setup
- Remote Jack Pack / TV Connections & Setup
- Reference
- Upgrading TV/PTC Software using a USB Memory Device
- Downloading a Splash Screen Image
- Power Consumption Settings
- TV Camport Auto Sense Operation
- TV Aux Input Configuration
- b-LAN Setup & Overview
- RJP Model List and Input Auto-sensing Hierarchy
- Resetting Factory Defaults on the TV(s)
- TV Zone Restrictions
- LD660H/LD665H Rear Jack Panel
- LV555H Rear Jack Panel
- Side Connections Panel
- RF Antenna Connection
- Troubleshooting
- Glossary of Terms
- Document Revision History / Notes
- BACK COVER
37
206-4200
1. Plug the USB memory device that contains the FTG Conguration
le into the Target LD660H/LD665H or LV555H TV USB IN port.
2. Press MENU on the Installer Remote to display the TV setup
menus (TV is in Pass-through Mode) or the Function Menu (TV is
already in FTG Mode).
3. Use the arrow navigation keys to select/highlight either the Option
menu icon from the TV setup menus or the Lock menu icon from
the Function Menu. Then, press the number “7” key a total of seven
times to display the USB Download Menu.
4. Use the Up/Down arrow keys to select Teach To TV (TLX), and then
press ENTER.
5. Use the Up/Down arrow keys to select the FTG Conguration le
you want to install, and then press ENTER.
The TV will show Teaching completion progress in a new window.
Do NOT remove the USB device until Teaching is complete. When
Teaching is complete, the TV will tune to the rst logical channel in
the FTG Channel Map.
6. When Teaching is done, remove the USB memory device. The
FTG Configuration should be resident on the Target TV. Also, the
Target TV CPU is now in FTG Mode (if it was previously in Pass-
through Mode).
Teach To TV (TLX)
xxLD660H-UA00005.TLX
Return Enter
USB Download Menu
Upgrade TV Software
Upgrade PTC Software
Teach To TV (TLL)
Teach To TV (TLX)
Return Enter
Teach To TV
UPDATING...
Do not unplug!
!
50%
Teaching FTG Conguration to a TV
This procedure describes how to “Teach” an FTG Conguration le from a USB memory device to a TV.
Ensure you have completed the procedure on the previous page to create the FTG Conguration le
before proceeding with the steps below.
Notes: • If the TV is not in FTG Mode, but both Pro:Centric items (098 PRO:CENTRIC and 119 DATA
CHANNEL) have already been set in the Installer Menu on a TV, Teach to TV options will not
be available from the USB Download Menu.
• If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to
the FTG Channel Map and FTG Installer Menu settings. You must use a direct PC-to-TV
connection as described on page 40 or an FMA head end device to recongure the EBL.
• If either of the preceding conditions applies, but you wish to switch the TV to FTG mode via
CPU, refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further
information before proceeding.
FTG Mode via CPU (Cont.)