Owner's Manual
Table Of Contents
- ACCESSORIES
- PREPARATION
- EXTERNAL EQUIPMENT SETUP
- WATCHING TV / PROGRAMME CONTROL
- Remote Control Key Functions
- Turning on the TV
- Programme Selection
- Volume Adjustment
- Quick Menu
- On Screen Menus Selection and Adjustment
- Freesat Programme Tuning (In Freesat Input -  )
- Non-Freesat Programme Tuning (In Freesat Input -  )
- Auto Programme Tuning (In Antenna Input -  )
- Manual Programme Tuning (In Digital Antenna Mode -  DTV)
- Manual Programme Tuning (In Analogue Antenna Mode -  TV)
- Programme Edit (In Non-Freesat, Digital Antenna or Analogue Antenna Mode Only)
- Custom Edit (In Freesat Mode Only - Freesat)
- Software Update (In Freesat Mode - Freesat)
- Software Update (In Digital Antenna Mode -  DTV)
- Diagnostics
- CI Information (Only for Digital Antenna Mode -  DTV)
- Network (In Freesat Mode- Freesat) (For Future Use)
- Selecting the Programme List
- Input List
- Input Label
- AV Mode
- Initializing (Reset to original factory settings)
- TO USE A USB DEVICE
- TV GUIDE (EPG; ELECTRONIC PROGRAMME GUIDE)(In Freesat, Non-Freesat or Digital Antenna Mode)
- PICTURE CONTROL
- SOUND & LANGUAGE CONTROL
- TIME SETTING
- PARENTAL CONTROL / RATINGS
- TELETEXT (For Analogue Antenna Mode)
- DIGITAL TELETEXT (For Freesat or Digital Antenna Mode)
- APPENDIX
GB-102
APPENDIX
TROUBLESHOOTING
The TV does not operate properly.
The remote control
does not work
- Check to see if there is any object between the TV and the remote control causing an
obstruction. Ensure you are pointing the remote control directly at the TV.
- Ensure that the batteries are installed with correct polarity (+ to +, - to -).
- Install new batteries.
Power is suddenly
turned off
- Is the sleep timer set?
- Check the power control settings. Has the Power supply been interrupted.
- Is Auto Sleep activated on this station?.
The video function does not work.
No picture & No sound - Check whether the TV is switched on.
- Try another channel. The problem may be with the broadcast.
- Is the power cord inserted correctly into the mains?
- Check your antenna direction and/or location.
- Test the mains outlet by plugging another product into the same outlet.
Picture appears slowly
after switching on
- This is normal, the image is muted during the TV startup process. Please contact your
service centre, if the picture has not appeared after ve minutes.
No or poor colour
or poor picture
- Adjust Colour in menu option.
- Allow a sufcient distance between the TV and the VCR.
- Try another channel. The problem may be with the broadcast.
- Are the video cables installed properly?
- Activate any function to restore the brightness of the picture.
Horizontal/vertical bars
or picture shaking
- Check for local interference such as an electrical appliance or power tool.
Poor reception on
some channels
- Station or cable channel experiencing problems, tune to another station.
- Station signal is weak, reposition the antenna to receive weaker stations.
- Check for sources of possible interference.
Lines or streaks
in pictures
- Check antenna (Change the position of the antenna).
No picture when
connecting HDMI
- Check that your HDMI cable is version 1.3 or higher.
- If the HDMI cables don’t support HDMI version 1.3, icking or no screen display can result.
Please use the latest cables that support at least HDMI version 1.3.
The audio function does not work.
Picture OK & No sound
- Press the + or - button.
- Sound muted? Press MUTE button.
- Try another channel. The problem may be with the broadcast.
- Are the audio cables installed properly?
No output from one
of the speakers
- Adjust Balance in menu option.
Unusual sound from
inside the TV
- A change in ambient humidity or temperature may result in an unusual noise when the TV is
switched on or off and does not indicate a fault with the TV.
No sound when
connecting HDMI or USB
- Check HDMI cable over version 1.3.
- Check USB cable over version 2.0.
APPENDIX