OWNER’S MANUAL LED LCD TV Please read this manual carefully before operating your set and retain it for future reference. LT36** www.lg.
TABLE OF CONTENTS ENGLISH TABLE OF CONTENTS 3 Licenses 19 TROUBLESHOOTING 3 OPEN SOURCE SOFTWARE NOTICE 20 SPECIFICATIONS 4 Installation Procedure 4 ASSEMBLING AND PREPARING 4 7 8 9 9 11 12 14 Unpacking Parts and buttons Lifting and moving the TV Setting up the TV - Attaching the stand Mounting on a table Mounting on a wall Tidying cables 23 IR CODES 24 EXTERNAL CONTROL DEVICE SETUP 24 24 24 25 25 26 RS-232C Setup Type of connector; D-Sub 9-Pin Male RS-232C Configurations Communication Par
LICENSES / OPEN SOURCE SOFTWARE NOTICE 3 Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING ENGLISH NOTE Image shown may differ from your TV. yy Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. yy The available menus and options may differ from the input source or product model that you are yy using. New features may be added to this TV in the future. yy The TV can be placed in standby mode in order to reduce the power consumption.
ASSEMBLING AND PREPARING 5 ENERGY ENGLISH TV/RAD SAVING GUIDE INFO RATIO ENERGY AV MODE INPUT TV SAVING LIST SETTINGS 1 2 4 5 7 8 LIST 0 3 6 Q.VIEW 9 FLASHBK Q.MENU MARK FAV VOL 3D CH P A G E MUTE EXIT MENU INFO Q.MENU FAV ENTER P P A G E MUTE BACK EXIT L/R SELECT FREEZE RATIO Remote control and batteries (AAA) (See p. 18) Owner’s manual Cable holder (Depending on model) (See p.
ASSEMBLING AND PREPARING ENGLISH NOTE Antenna Isolator Installation Guide yy -- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal. »» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be heated and excessive heat might cause an accident. -- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recommended to mount the isolator to the wall.
ASSEMBLING AND PREPARING 7 ENGLISH Parts and buttons Screen Buttons (Only 32/37/42/47LT36**) Buttons (Only 22/26LT36**) P Remote control sensor R IN 3 Power Indicator (Can be adjusted using the Power Indicator in the OPTION menu.) Button v^ - + Stand (Only LT360C, LT361C, LT365H) Speakers Description Scrolls through the saved programmes. Adjusts the volume level. Turns the power on or off.
ASSEMBLING AND PREPARING ENGLISH Lifting and moving the TV When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. When transporting a large TV, there should yy be at least 2 people. When transporting the TV by hand, hold the yy TV as shown in the following illustration. CAUTION Avoid touching the screen at all times, as this yy may result in damage to the screen.
ASSEMBLING AND PREPARING 9 ENGLISH Setting up the TV Image shown may differ from your TV.
ASSEMBLING AND PREPARING ENGLISH (Only 32/37/42/47LT360C) 1 3 M4 x 14 4 EA Stand Body M4X20 Front Stand Base M4 x 14 4 EA Top View 2 CAUTION When attaching the stand to the TV set, yy place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. Make sure that the screws are fastened yy completely. (If they are not fastened securely enough, the TV may tilt forward after being installed.
ASSEMBLING AND PREPARING Securing the TV to a table 1 Lift and tilt the TV into its upright position on a table. -- Leave a 10 cm (minimum) space from the wall for proper ventilation. Fix the TV to a table to prevent from tilting forward, damage, and potential injury. To secure the TV to a table, insert and tighten the supplied screw on the rear of the stand. (Only 32/37/42/47LT360C) 10 cm 10 cm 10 cm 2 Connect the power cord to a wall outlet.
ASSEMBLING AND PREPARING ENGLISH Securing the TV to a wall (This feature is not available for all models.) 1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. - - If there are bolts inserted at the eye-bolts position, remove the bolts first. Mount the wall brackets with the bolts to the 2 wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
ASSEMBLING AND PREPARING Separate purchase (Wall Mounting Bracket) 22LT36** 26LT36** VESA 100 x 100 Standard screw M4 Number of 4 screws Wall mount LSW100B(G) bracket Model 32LT36** 200 x 100 M4 4 CAUTION Disconnect the power first, and then move or yy install the TV. Otherwise electric shock may occur. If you install the TV on a ceiling or slanted yy wall, it may fall and result in severe injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.
ASSEMBLING AND PREPARING / MAKING CONNECTIONS Tidying cables ENGLISH (Only 32/37/42/47LT36**) 1 Install the Power Cord Holder and Power Cord. It will help prevent the power cable from being removed by accident. Power Cord Holder 2 Gather and bind the cables with the cable holder. Cable Holder (Only 22/26LT36**) 1 Gather and bind the cables with the cable holder.
MAKING CONNECTIONS 15 Antenna connection (Only 22/26LT36**) Connect the TV to a wall antenna socket with an RF cable (75 Ω). DC IN ANTENNA/ CABLE IN DC Adapter 1 Connect the antenna cable to the antenna input port on the TV. 2 Connect the DC adapter plug to the power input jack on the TV. 3 onnect the power cord to the DC adapter C first, then plug the power cord into the wall power outlet. External speaker out Connecting External Speaker.
MAKING CONNECTIONS DVI to HDMI connection Transmits the digital video and audio signals from your PC to the TV. Connect the PC and the TV with the HDMI cable as shown. Choose any HDMI input port to connect. It does not matter which port you use. Transmits the digital video signal from an external device to the TV. Connect the external device and the TV with the DVI-HDMI cable as shown. To transmit an audio signal, connect an audio cable. Choose any HDMI input port to connect.
MAKING CONNECTIONS 17 RGB-PC connection Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with th e composite cable as shown. Transmits the video signal from PC to the TV. To transmit an audio signal, connect an audio cable.
REMOTE CONTROL ENGLISH REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching the and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION Do not mix old and new batteries, as this may damage the remote control.
MAINTENANCE / TROUBLESHOOTING ENGLISH MAINTENANCE Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION Make sure to turn the power off and disconnect the power cord and all other cables first. yy When the TV is left unattended and unused for a long time, disconnect the power cord from the wall yy outlet to prevent possible damage from lightning or power surges.
SPECIFICATIONS ENGLISH SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. MODELS Dimensions (W x H x D) Weight 26LT360C-TA 26LT365H-TA 32LT360C-TA 516.6 x 385.7 x 192.0 625.9 x 453.5 x 192.0 765.6 x 535.6 x 231.9 516.6 x 332.2 x 41.6 625.9 x 393.2 x 46.6 765.6 x 475.8 x 68.5 With stand (kg) 3.7 3.1 4.7 4.1 9.2 8.0 DC 24 V, 1.
SPECIFICATIONS New Zealand, Singapore 0 °C to 40 °C Operation Humidity Less than 80 % Storage Temperature -20 °C to 60 °C Storage Humidity Less than 85 % Television System Programme Coverage Australia Television System Programme Coverage Indonesia, Israel, Myanmar, Sri Lanka Television System Programme Coverage Vietnam, Malaysia Television System Programme Coverage Iran, Algeria, Tunisia, Digital model Television System Programme Coverage Analogue model, India, Thailand, South Africa -- T
SPECIFICATIONS ENGLISH HDMI/DVI-DTV supported mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 720x480 31.469 31.5 59.94 60 720x576 31.25 50 1280x720 37.5 44.96 45 50 59.94 60 1920x1080 33.72 33.75 28.125 26.97 27 33.716 33.75 56.25 67.43 67.5 59.94 60 50 23.97 24 29.976 30.00 50 59.94 60 RGB-PC, HDMI/DVI-PC supported mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 720x400 31.468 70.08 640x480 31.469 59.94 800x600 37.879 60.
IR CODES ENGLISH IR CODES This feature is not available for all models. yy Code (Hexa) 08 95 0B F0 10-19 53 1A Function (POWER) ENERGY SAVING INPUT TV/RAD Number Key 0-9 LIST Q.
EXTERNAL CONTROL DEVICE SETUP ENGLISH EXTERNAL CONTROL DEVICE SETUP RS-232C Setup RS-232C Configurations Connect the RS-232C (serial port) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Connect the serial port of the control device to the RS-232C jack on the product back panel. Note: RS-232C connection cables are not supplied RGB IN (PC) with the product.
EXTERNAL CONTROL DEVICE SETUP 25 ENGLISH Communication Parameters yy Stop bit: 1 bit yy Communication code: ASCII code yy Use a crossed (reverse) cable. yy Baud rate: 9600 bps (UART) yy Data length: 8 bits yy Parity : None Command reference list (Depending on model) DATA COMMAND1 COMMAND2 (Hexadecimal) k a 00 to 01 13. Treble DATA COMMAND1 COMMAND2 (Hexadecimal) k r 00 to 64 k c (See p.27) 14. Bass k s 00 to 64 k d (See p.27) 15.
EXTERNAL CONTROL DEVICE SETUP ENGLISH Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] [Command 2] [Set ID] : First command to control the TV.(j, k, m or x) : Second command to control the TV. : You can adjust the set ID to choose desired monitor ID number in option menu. Adjustment range is 1 to 99. When selecting Set ID ‘0’, every connected set is controlled.
EXTERNAL CONTROL DEVICE SETUP 27 04. Volume Mute (Command: k e) ►► To control Power On/Off of the set. ►► To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To show Power On/Off.
EXTERNAL CONTROL DEVICE SETUP ENGLISH 09. Tint (Command: k j) 13. Treble (Command: k r) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. ►► To adjust treble. You can also adjust treble in the AUDIO menu. Data Transmission [k][j][ ][Set ID][ ][Data][Cr] Red : 00 to Green : 64 * Refer to ‘Real data mapping’. See p.30. Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 * Refer to ‘Real data mapping’. See p.30.
EXTERNAL CONTROL DEVICE SETUP 19. Tune Command (Command: m a) ►► To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu. ►► Select channel to following physical number.
EXTERNAL CONTROL DEVICE SETUP 23. Input select (Command: x b) (Main Picture Input) ENGLISH ►► To select input source for main picture.
Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. Model : Serial No.
