Installation Manual

39
206-4313
Installer Menu (Cont.)
Installer Menu Items 000 through 046
Item Function Value Range Default Value Brief Description of Function
000 INSTALLER SEQ 0 – 3 0 Leave default set to 0.
001 POWER MANAGE 0 – 7 0
Selects the number of hours of inactivity allowed before the TV automatically
turns itself OFF. Set to 0 to disable Power Management.
002 AC ON 0 – 3 0
Set to 1 to enable TV to turn ON when AC power is applied. Set to 2 or 3 to
enable Instant ON when AC power is applied. (See detailed descriptions.)
003 BAND/AFC 0 – 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC
004 STRT CHANNEL 0 – 127, 253, 255 255
Channel tuned when TV is turned ON. (Set to 255 to tune to channel
tuned before TV turned OFF.)
005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.
007 STRT VOLUME 0 – 63, 255 255
Volume level when TV is turned ON. (Set to 255 to use volume level
before TV turned OFF.)
008 MIN VOLUME 0 – 63 0 Sets minimum allowable volume setting.
009 MAX VOLUME 0 – 63 63 Sets maximum allowable volume setting.
010 MUTE DISABLE 0 / 1 0 Set to 1 to disable Mute Function.
011 KEY DEFEAT 0 / 1 1
If set to 1, joystick button menu navigation functions on display panel are
not available.
012 IR BANKS EN. 0 / 1 0 Set to 1 to enable TV to respond to bank discrete IR codes.
013 SCAN MODE 0 / 1 1 Set to 1 to allow Channel Up/Down to turn ON TV. (See detailed descriptions.)
014 STRT CH IN SM 0 / 1 0 Set to 1 to use the Start Channel for the Channel Map pivot point in Scan Mode.
015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.
016 EN. TIMER 0 / 1 1 Set to 1 to enable On/Off Timers.
017 ALARM 0 / 1 1 Set to 1 to enable Alarm.
020 FEATURE LEVEL
0, 1, 16 – 24,
64, 65
1 Determines an additional IR code scheme to which the TV will respond.
021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip (Parental Control) functions.
022 MAX BLK HRS 0 – 99 12 Sets number of V-Chip blocking hours.
023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting set before TV turned OFF.
025 FUNCTION PRE. 0 / 1 1
Set to 1 to allow Channel Preview/Banks Setup Menu access via CH
PREVIEW key on Installer Remote.
027 HOSPITAL MODE 0 – 162, 254 254
Set according to the speaker selection, the pillow speaker code/supply voltage,
and the hospital IR code. See detailed instructions.
028 CH. OVERIDE 0 / 1 1
If set to 0, users can only tune to channels that are included in the PTC
Channel Map. (See detailed descriptions.)
029 OLD OCV 0 / 1 0 Set to 1 to remap the PTC’s direct tune channels for Aux inputs from 13x to 9x.
030 ACK MASK 0 / 1 0 If set to 1, enables ACK feature of MPI.
031 POLL RATE 20 – 169 94 Selects poll rate for MPI.
032 TIMING PULSE 186 – 227 207 Sets baud rate for MPI.
035 HDMI1 ENABLE 0 – 2 1
Set to 0 to disable HDMI 1. Set to 1 (DTV Mode) or 2 (PC Mode), as
applicable, to enable HDMI 1.
039 REAR AUX EN. 0 / 1 1 Set to 1 to enable display panel AV input jack.
041 SIMPLINK EN 0 / 1 0 Determines the status of the SIMPLINK feature. (See detailed descriptions.)
042 AUTO INPUTS 0 – 255 0
Determines the Aux inputs for which auto-sensing is enabled. (See detailed
descriptions.)
046 STRT AUX SRCE 1, 3, 5, 255 255 Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).