Installation Manual
90
206-4313
Reference: Using the TV’s Zoning Features (Cont.)
Using the Wi-Fi Zoning Feature with Cloning Conguration
A location-specic Wi-Fi conguration / Clone (.tlx) le may be saved (exported) from a Master TV and
then be used to congure Target TVs. First, the wireless network (i.e., the access point login data) must
be congured in the Master TV’s IP Environment Menu (see “Conguring a Wi-Fi Network Connection”
on page 67). Then, a Wi-Fi Zone # must be set in the Master TV (see “Set the TV Zone # and/or Wi-Fi
Zone # in the TV” below). If desired, a TV Zone # may also be set in the Master TV.
For example, if the Wi-Fi Zone # is set to 4 and the TV Zone # is set to 5 before the Clone le export is
initiated, the Master TV’s Installer Menu prole will be saved with the Zone 5 assignment, and within that
Installer Menu prole, the access point login data for wireless networking (i.e., SSID, security type, and
security key) will be saved with a Wi-Fi Zone 4 assignment. In order to congure the Target TVs with the
proper Installer Menu prole and access point login data, you must set both the TV Zone # and the Wi-Fi
Zone # in the Target TVs accordingly before importing the Clone le. See “Set the TV Zone # and/or Wi-Fi
Zone # in the TV” below. Also, see “Cloning Procedures” on pages 52 to 58 for additional information
on the cloning processes. If the Wi-Fi Zone # in the TV is set to 0 (default), the TV will not obtain access
point login data from the Installer Menu prole with which it is congured unless the prole contains the
global Wi-Fi Zone 100. Any TV that does not nd its matching Wi-Fi Zone # in the Clone le, but does nd
the global Wi-Fi Zone 100, will be congured with the global access point login data.
Set the TV Zone # and/or Wi-Fi Zone # in the TV
You can set the TV Zone # and/or the Wi-Fi Zone # in the EZ-Manager Wizard (see “EZ-Manager Wizard”
on pages 14 to 22) or, if the TV is in Pass-through Mode, via the TV’s setup menus as described below.
Note that the following procedure can only be performed while the TV is in Pass-through Mode. You will also
be able to specify a Label (North, South, East, West) and Room Number for this TV, if desired.
1. Turn ON the TV.
2. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the
General menu icon. Then, press OK.
3. In the General Menu, use the Up/Down arrow keys to select Room Info, and then press OK.
4. In the Room Info screen, complete the appropriate elds as described below. Use the Up/Down arrow
keys on the Installer Remote to navigate between each of the elds.
• Wi-Fi Zone: Enables you to set a Wi-Fi Zone # so that the TV can be congured with a particular
access point’s login data for wireless networking. Login data (i.e., SSID, security type, and security
key) may be provided in a Clone/Conguration (.tlx) le.
To assign a Wi-Fi Zone, select/highlight the Wi-Fi Zone eld and press OK. Then, use the Left/Right
arrow keys to specify the desired Wi-Fi Zone # (1–99). Press OK when you are nished.
• TV Zone: Enables you to set a TV Zone # so that the TV can be congured with Installer Menu
and/or Setup Menu settings intended only for the assigned Zone. The Installer Menu and/or Setup
Menu settings may be provided in a Clone/Conguration (.tlx) le. If the TV is being congured for
FTG Mode via CPU, the TV Zone # setting also allows the TV to omit channels that have been
restricted in the FTG Channel Map (see “FTG Channel Map Zone Restrictions” on page 88).
To change the TV Zone, select/highlight the TV Zone eld and press OK. Then, use the Left/Right
arrow keys to specify the desired TV Zone # (0–8). Press OK when you are nished.
(Continued on next page)