INSTALLATION MANUAL LG Digital Signage (MONITOR SIGNAGE) Please read this manual carefully before operating the your set and retain it for future reference. webOS 3.0 www.lg.
ENGLISH CONTENTS ACCESSING INSTALLATION MENU..............................................4 White Balance INSTALLATION MENU...................5 Status Message -- Signage Setup.....................................................................
-- Server....................................................................................27 Off Set Automatically Auto Server IP Type Manual -- ISM Method.......................................................................23 Server IP Server Status Mode Port Number Repeat Secured Connection Wait Control Server IP Type Duration Control Server IP Repeat Day Control Server Port Start Time End Time Control Server Status -- Lock Mode....................................................
ENGLISH ACCESSING INSTALLATION MENU 1 Press and hold the SETTINGS button for 5 seconds. or 2 When Input ID (The top right corner ) is displayed, enter your password. (The default value is 0, 0, 0, 0 ) 3 When the Installation Menu is displayed, select the desired option. -- Signage Setup -- USB Cloning -- Password Change -- Fail Over -- ISM Method -- Server -- Lock Mode NOTE •• Images in the manual may look different from the actual product.
NOTE •• Some features described in the Installation manual may not be supported in certain models. Signage Setup Use this menu to configure the digital signage after installation. Power On Status •• You can select the operating status of the monitor when the main power is switched on. •• You can select from among PWR, STD, and LST. •• PWR sets the status of the monitor to on whenever the main power is switched on. •• STD sets the status of the monitor to standby when the main power is switched on.
Power Off Management ENGLISH •• No Signal Power Off (15 Min) -- You can choose whether to use the 15 min force off feature. -- You can set this option to On or Off. -- If you set this option to On, the product turns off when it has remained in no signal status for 15 minutes. -- If you set this option to Off, the 15 min force off feature is disabled. -- Set this option to Off when you use the product for a long period of time. •• Auto Power Off -- You can choose whether to use the 4 hours off feature.
NOTE •• Set to Screen Off & Backlight (Outdoor Mode) when installing outdoors. •• When the Outdoor mode is set, you can reduce the cause for internal humidity and condensation in the product. •• When operating in low temperatures, the enclosure may not work for up to one hour to raise the internal temperature of the enclosure. •• For compatibility of some media input devices, set the Sustain Aspect Ratio. ENGLISH •• PM Mode -- Power Off: Normal DC off status.
Rotation ENGLISH •• OSD Portrait Mode -- This feature allows you to rotate the OSD clockwise. -- You can set this feature to Off/90/180/270. (Some models only support certain settings.) -- If you set this feature to Off, the feature is disabled. -- If you set this feature to 90, the OSD rotates 90 degrees clockwise. In this case, the mouse cannot be used. -- If you set this feature to 180, the OSD rotates 180 degrees clockwise. In this case, the mouse cannot be used.
Beacon Baudrate (9600/115200) •• You can change the RS-232C communication speed for controlling your monitor. •• You can choose 9600 or 115200. •• If you set this option to 9600, the RS-232C communication speed is set at 9600 bps. •• If you set this option to 115200, the RS-232C communication speed is set at 115200 bps. ENGLISH •• Enables BLE Beacon, one of Bluetooth 4.0's features. •• Beacon Mode (on/off toggle): Enables the Beacon feature.
Power On Delay (0 ~ 250) ENGLISH •• This feature delays power on in order to prevent overload when multiple monitor sets are turned on simultaneously. •• You can set the delay interval in the range of 0 to 250 seconds. Check Screen •• The Check Screen feature judges whether there are abnormalities at the edges of the screen. R, G, and B OSDs are formed on the screen at one second intervals and an Pixel Sensor tests the areas. •• If set to On, the Check Screen feature is enabled.
Interface Selection OPS Power Control •• You can control the power of the OPS. •• Disable: Disables the OPS Power Control. •• Sync (on): Synchronizes the power status of the monitor and the OPS only when monitor is on. •• Sync (on/off): Always synchronizes the power status of the monitor and the OPS. •• When you set the OPS Power Control feature to on, you must set the sustain Aspect Ratio of the PM Mode to off.
Sync Mode ENGLISH •• Syncs the products to the time, brightness and content of one product. •• Off: Sync is disabled. •• RS-232C: Syncs multiple monitors connected via RS-232C. -- Master/Slave: These monitors can be set to Master or Slave. Only one monitor should be set to Master mode for this feature to work properly. -- Time Sync: When Time Sync is set to On, the current time of the Master monitor is sent to multiple Slave monitors connected via RS-232C to sync the time.
Intelligent Auto Studio Mode •• Outputs the images with a lower color temperature. •• You can set this feature to On or Off. •• Setting this feature to On lowers the color temperature of the images. HDMI IT Contents •• Sets the HDMI IT Contents function. •• Disable: Does not use the HDMI IT Contents function. •• Enable: Uses the HDMI IT Contents function. •• This function automatically changes the Picture mode based on HDMI Contents information when an HDMI signal is entered.
Application ENGLISH •• Adds/deletes applications in the Launcher bar. •• We recommend that if you are to remove the Screen Share app from the home launcher by unchecking the Screen Share item, you should reboot your system after removal. •• When Content Rotation or OSD Portrait Mode is set to On, the 'Group Manager' app is removed from the launcher and the 'Group Manager' item is deactivated. •• When the Control Manager is set to On, the Control Manager app will be added to the Launcher bar.
Status Message ENGLISH •• Sets up a feature that sends the status of Signage to users' email addresses. •• The administrator can set Status Message to On or Off. •• Messaging Period: Sets a time interval to send messages. You can select either When Failure Status or Weekly. •• Select Date: Available if you have set Messaging Period to Weekly. Select your desired day of the week for message transmission. •• Select Time: Available if you have set Messaging Period to Weekly.
SIMPLINK Setup ENGLISH •• When the SIMPLINK Setup is set to On, you can use the SIMPLINK provided by LG Signage. •• Device ID: S ets the ID of the device connected via CEC wiring. You can choose a value between 'All' and 'E'. •• StandBy: Sets the scenarios for sending and receiving the OpStandBy (0x0c) command. Detailed scenarios are as follows: Send Receive Send Only O X Receive Only X O All O O Local Dimming •• Sets whether to use the Local Dimming feature.
Analog Signage BLU Setting Crestron •• This function enables synchronization with applications provided by Crestron. •• Server: This menu sets the server's IP address for the network connection with the server (equipment provided by Crestron). •• Port: This menu sets the port for the network connection with the server. The default port number is 41794. •• IP ID: This menu sets a unique ID for synchronizing with the application.
Signage 365 Care ENGLISH •• You can install the Signage 365 Care (fault diagnosis) solution for fault diagnosis and prediction service. •• Install: Installs the Signage 365 Care solution. 1) ENTER ACCOUNT NUMBER: Enters the 6-digit account number to install the Signage 365 Care solution. -- Account Number: The number assigned when the Signage 365 Care solution is registered. When the account number is entered, the account name corresponding to the number is obtained.
Guide to Using Content Rotation Original 2 2 Content Rotation (270 degrees) Rotating displays (90 degrees) 2 ENGLISH [Portrait installation setting] You can turn the image into a portrait image using Content Rotation. When installing the display rotated 90 degrees: Set Content Rotation to 270. When installing the display rotated 270 degrees: Set Content Rotation to 90.
ENGLISH [Video wall installation setting] You can implement a landscape and portrait video wall using Content Rotation.
You can copy the product settings to other sets. Send to USB •• You can save the current settings in file format to a USB device.
ENGLISH Fail Over The input source with the highest priority will be selected. Off •• The Auto-Fail Over feature is disabled. Auto •• The input source changes according to the specified order. When several input sources are found, the input source with the highest priority will be selected. •• Priority Case 1) 1. HDMI, 2. DVI-D, 3. DISPLAYPORT, 4. OPS, 5. RGB, 6. Internal Memory Case 2) 1. HDMI1, 2. HDMI2, 3. OPS/HDMI3/DVI-D or OPS/DVI-D, 4. DP, 5.
If a still image is displayed on the screen for an extended period of time, image sticking can occur. The ISM method is a feature that prevents image sticking. Mode •• Selects the desired ISM Method mode. •• Normal: Disables the ISM method. •• White Wash: Displays a white pattern to remove image sticking. •• Color Wash: Alternately displays a white pattern and a color pattern to remove image sticking. •• User Image: Displays your desired images using USB. •• User Video: Plays your desired video.
Repeat ENGLISH •• Off, just 1 time: If you select the desired mode and press DONE, ISM operates immediately. •• On: If the screen remains still for a specified wait time, ISM operates for the specified duration time. •• On, with moving detection: Only applies to Orbiter mode. If the screen remains still for the specified Wait time, ISM operates for the specified Duration time. •• On, without moving detection: Only applies to Orbiter mode.
Action Cycle Bar Image •• Off: Displays a bar with a fixed resolution of 300 x 1080, then moves the bar. •• On: Displays and moves an image downloaded by the user. The image is displayed with a fixed height of 1080 and the same width as downloaded. However, if the width of the image is below 300, it will have a fixed value of 300. •• This option is available only when you have selected Washing Bar. •• If you have downloaded only one image, the bar is moved and the image is displayed alone.
Bar Image Download ENGLISH •• To download an image, the image file must be located under the folder titled "ISM" on your USB drive. •• Make sure to delete the old images stored in the internal memory before downloading a new image file. •• Supported image file types: "BMP", "JPG", "JPEG", "PNG" •• You can download up to four images. (Resolution: 1920 x 1080 or lower) •• If there are no images, or if the existing images have been deleted, the default image is used.
Set Automatically •• The monitor settings will be set automatically so that the SuperSign server can search it. Server IP Type •• Select the IPv4 or the IPv6 type. Server IP •• This is a menu where you can set an IP address for the SuperSign server. Server Status •• Server Status displays the status of the connection between your monitor and the SuperSign server. •• Not Connected - indicates that your monitor is not connected to the SuperSign server.
ENGLISH Lock Mode USB •• You can prevent the use of USB devices. OSD •• You can prevent OSD from displaying. Wi-Fi •• This feature enables you to turn the Wi-Fi feature on or off. Reset to Initial Settings •• You can restore the initial settings with this feature. IR Operation •• If you set IR Operation to Normal, you can use the remote control. •• If you set IR Operation to Power Key Only, you can only use the Power Key. •• If you set IR Operation to Block All, you cannot use the remote control.
