OWNER’S MANUAL LED TV* * LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your TV and retain it for future reference. 50LN5100 55LN5100 47LN5200 32LN530B 50LN5200 32LN5300 55LN5200 39LN5300 42LN5300 P/NO : MFL67651192 (1309-REV05) 32LN5310 47LN5310 50LN5310 55LN5310 32LN536B 42LN5400 47LN5400 50LN5400 55LN5400 www.lg.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product. WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS Protect the power cord from being walked on yy or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified yy by the manufacturer. Use only with a cart, stand, tripod, bracket, yy or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
IMPORTANT SAFETY INSTRUCTIONS Grounding yy (Except for devices which are not grounded.) Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.
IMPORTANT SAFETY INSTRUCTIONS Preventing image burn or burn-in on your TV screen If a fixed image displays on the TV screen for yy a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is image burn or burn-in and not covered by the warranty. If the aspect ratio of the TV is set to 4:3 for a yy long period of time, image burn may occur on the letterboxed area of the screen.
IMPORTANT SAFETY INSTRUCTIONS For USA and Canada FCC NOTICE ENGLISH This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
LICENSES / OPEN SOURCE SOFTWARE NOTICE 7 LICENSES Supported licenses may differ by model. For more information about licenses, visit www.lg.com. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
TABLE OF CONTENTS TABLE OF CONTENTS 2 IMPORTANT SAFETY INSTRUCTIONS 26 REMOTE CONTROL 6 Additional information of the manual 28 WATCHING TV 7 LICENSES 28 Turning the TV on for the first time 7 OPEN SOURCE SOFTWARE NOTICE 29 SPECIFICATIONS 32 TROUBLESHOOTING 34 EXTERNAL CONTROL DEVICE SETUP 8 TABLE OF CONTENTS 9 Installation Procedure ENGLISH 9 ASSEMBLING AND PREPARING 9 11 12 13 13 14 16 17 Unpacking Parts and buttons Lifting and moving the TV Setting up the TV - Attaching th
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING 9 Installation Procedure 1 2 3 Open the package and make sure all the accessories are included. Attach the stand to the TV set. Connect an external device to the TV set. ASSEMBLING AND PREPARING Unpacking CAUTION Do not use any unapproved items to ensure the safety and product life span. yy Any damages or injuries by using unapproved items are not covered by the warranty. yy Some models appear to have a thin film on the screen.
ASSEMBLING AND PREPARING ENGLISH Remote Control, Batteries (AAA) (See page. 26) Owner’s Manual, CD manual Power Cord Stand Body, Stand Base (See page. 13) Stand Screws 3 EA, P5 x 25 (See page. 13) Stand Screws 4 EA, M4 x 14 (See page. 13) (For 50LN5100, 47/50LN5200, 32LN530B, 32/39/42LN5300, 32/47/50LN5310, 32LN536B, 42/47/50LN5400) Desk-mount Screw (See page. 14) Cable Holder (See page.
ASSEMBLING AND PREPARING 11 Parts and buttons Screen ENGLISH Speakers Power Indicator Remote Control Sensor Intelligent Sensor1 Button Description / ( / ) Scrolls through the saved channels. / ( / ) Adjusts the volume level. (OK Selects the highlighted menu option or confirms an input. ) (SETTINGS) Accesses the main menus, or saves your input and exits the menus. (INPUT Changes the input source. ( ) Buttons ) Turns the power on or off.
ASSEMBLING AND PREPARING Lifting and moving the TV When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. Use at least two people to move a large TV. yy When transporting the TV by hand, hold the yy TV as shown in the following illustration. CAUTION Avoid touching the screen at all times, as yy this may result in damage to the screen.
ASSEMBLING AND PREPARING 13 Setting up the TV You can mount your TV to a wall or attach the stand if you wish to place the TV on an entertainment center or other furniture. Attaching the stand If you are not mounting the TV to a wall, use the following instructions to attach the stand. CAUTION When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat yy surface to protect the screen from scratches. Make sure that the screws are fastened tightly.
ASSEMBLING AND PREPARING Mounting on a table 1 Securing the TV to a table Lift and tilt the TV into its upright position on a table. - Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. (For 50LN5100, 47/50LN5200, 32LN530B, 32/39/42LN5300, 32/47/50LN5310, 32LN536B, 42/47/50LN5400) Attach the TV to a table to prevent from tilting forward, damage, and potential injury. Mount the TV on a table, and then insert and tighten the supplied screw on the rear of the stand.
ASSEMBLING AND PREPARING Using the Kensington security system (optional) The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www. kensington.com. Connect the Kensington security system cable between the TV and a table.
ASSEMBLING AND PREPARING Mounting on a wall Wall mount bracket (optional) An optional wall mount can be used with your LG Television. Consult with your local dealer for a wall mount that supports the VESA standard used by your TV model. Carefully attach the wall mount bracket at the rear of the TV. Install the wall mount bracket on a solid wall perpendicular to the floor. If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount.
ASSEMBLING AND PREPARING 17 Tidying cables 1 Install the cable holder as shown. Cable Holder 2 Gather and bind the cables with the cable holder. ENGLISH Cable Holder CAUTION Do not move the TV by holding the cable yy holder, as the cable holders may break, and injuries and damage to the TV may occur.
MAKING CONNECTIONS MAKING CONNECTIONS You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. For more information on external device’s connection, refer to the manual provided with each device. NOTE If you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input yy cable to the TV through a DVD recorder or VCR.
MAKING CONNECTIONS 19 Connecting to a HD receiver, DVD player, or VCR Connect a HD receiver, DVD player, or VCR to the TV and select an appropriate input mode. HDMI connection HDMI is the best way to connect a device. Transmits digital video and audio signals from an external device to the TV. Connect the external device and the TV with the HDMI cable as shown in the following illustration. NOTE Use the latest High Speed HDMI™ Cable that supports CEC (Customer Electronics Control) yy function.
MAKING CONNECTIONS Connecting to a mobile phone (For LN5200, LN530B, LN5300, LN5310, LN5400 series) Mobile High-definition Link (MHL) is an interface for transmitting digital audio/visual signals from mobile phones to television sets. NOTE IN 2 (MHL) Connect the mobile phone to the HDMI IN 2 (MHL) port to view the phone screen on the TV. yy This only works with an MHL-enabled phones. yy With some MHL supporting mobile phones, you can use the TV remote to control the phone.
MAKING CONNECTIONS 21 Component connection Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with a component cable as shown in the following illustration. NOTE If cables are installed incorrectly, it could cause the image to display in black and white or with yy distorted color. Check to ensure the cables are matched with the corresponding color connection.
MAKING CONNECTIONS Composite connection Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with the composite cable as shown in the following illustration. NOTE If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the yy TV. Check to ensure the cables are matched with the corresponding color connection.
MAKING CONNECTIONS 23 Connecting a PC NOTE Use an HDMI connection for the best image quality. yy Depending upon the graphics card, DOS mode video may not work if a HDMI to DVI Cable is in use. yy In PC mode, there may be noise associated with the resolution, vertical pattern, contrast, or yy brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
MAKING CONNECTIONS Connecting to an audio system (For LN5100, LN5200, LN530B, LN5300, LN5310, LN5400 series) You can use an optional external audio system instead of the built-in speaker. Digital optical audio connection Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV with the optical audio cable as shown in the following illustration. NOTE Do not look into the optical output port. Looking at the laser beam may damage your vision.
MAKING CONNECTIONS 25 Connecting a USB device USB IN Connect a USB storage device such as a USB flash memory, external hard drive, or a USB memory card reader to the TV.
REMOTE CONTROL REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To install batteries, and open the battery cover, replace batteries (1.5 V AAA) matching the ends to the label inside the compartment, and close the battery cover. Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution.
REMOTE CONTROL FLASHBK AUDIO 27 PICTURE Changes the image mode. INFO Shows information on the current program. SOUND Changes the sound mode. Q.MENU Accesses the quick menu. Navigation buttons (up/down/left/right) Scrolls through menus or options. OK Selects menus or options and confirms your input. BACK Returns to the previous screen. EXIT Clears all on-screen displays and returns to TV viewing. Accesses the AV devices connected to the TV; Opens the SIMPLINK menu.
WATCHING TV WATCHING TV Turning the TV on for the first time When you turn the TV on for the first time, the initial setting screen appears. Select a language and customize the basic settings. 1 2 Connect the power cord to a power outlet. In standby mode, press the power button on the remote control to turn the TV on. The initial setting screen appears when you turn the TV on for the first time. NOTE You can also access Initial Setting by yy accessing OPTION in the main menu.
SPECIFICATIONS 29 SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions.
SPECIFICATIONS 47LN5200 (47LN5200-UB) MODELS 42LN5400 (42LN5400-UA) 47LN5310 (47LN5310-UB) 47LN5400 (47LN5400-UA) With stand Dimensions (W x H x D) 38.1 x 24.7 x 9.2 (inches) 42.5 x 27.3 x 10.3 (inches) 1,080 x 642 x 80.5 (mm) 38.1 x 22.7 x 3.1 (inches) 42.5 x 25.2 x 3.1 (inches) With stand 10.7 kg (23.5 lbs) 14.7 kg (32.4 lbs) Without stand 9.6 kg (21.1 lbs) 13.4 kg (29.5 lbs) 1.1 A / 110 W 1.
SPECIFICATIONS HDMI (PC) supported mode Component port connecting information Horizontal Frequency (kHz) Vertical Frequency (Hz) 640 x 350 31.468 70.09 720 x 400 31.469 70.08 640 x 480 31.469 59.94 800 x 600 37.879 60.31 1024 x 768 48.363 60.00 1360 x 768 47.712 60.015 1152 x 864 54.348 60.053 1280 x 1024 63.981 60.02 1920 x 1080 67.50 60.
TROUBLESHOOTING TROUBLESHOOTING General Problem Solution ENGLISH Cannot control the TV with the remote control. yyCheck the remote control sensor on the product and try again. yyCheck if there is any obstacle between the product and the remote control. to yyCheck if the batteries are still working and properly installed ( to , No image display and no sound is produced. yyCheck if the product is turned on. yyCheck if the power cord is connected to a wall outlet.
TROUBLESHOOTING 33 Video Problem Solution An image displays in black and yyAdjust the color setting in the menu option. white or the color quality is yyKeep a sufficient distance between this product and other electronic products. poor. yyScroll to other channels. There may a problem with the broadcast. yyCheck if there are local interferences such as an electrical appliance or power tool. Lines or streaks appear on images yyCheck the antenna or aim the antenna to the proper direction.
EXTERNAL CONTROL DEVICE SETUP EXTERNAL CONTROL DEVICE SETUP To obtain the external control device setup information, please visit www.lg.com.
CHILD SAFETY: It Makes A Difference How and Where You Use Your Flat Panel Display Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind: THE ISSUE • The home theater entertainment experience is a growing trend and larger flat panel displays are popular purchases. However, flat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations.
The extended owner’s manuals that contain information on the advanced features of this LG TV are located on the CD-ROM provided in an electronic version. To read these files, you will need to use a personal computer (PC) equipped with a CD-ROM drive. LG Customer Information Center For inquires or comments, visit www.lg.com or call; 1-800-243-0000 USA, Consumer User 1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA Register your product Online! www.lg.
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.
2 KEY CODES ENGLISH ENG KEY CODES • This feature is not available for all models. Code (Hexa) Function Note Code (Hexa) Function Note 00 CH +, PR + R/C Button 45 Q.
EXTERNAL CONTROL DEVICE SETUP 3 • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series. * Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB USB IN IN 4 EXTERNAL CONTROL DEVICE SETUP (PC) (PC) RS-232C IN (CONTROL & SERVICE) Phone jack Type RS-232C • You need to purchase the phone-jack to RS-232 cable required for theIN connection between the PC and (CONTROL & SERVICE) the TV, which is specified in the manual. (TV) (TV) (PC) (PC) * For other models, connect to the USB port.
EXTERNAL CONTROL DEVICE SETUP 5 • Baud rate : 9600 bps (UART) • Data length : 8 bits • Parity : None ENGLISH ENG Communication Parameters • Stop bit : 1 bit • Communication code : ASCII code • Use a crossed (reverse) cable. Command reference list (Depending on model) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power off k a 00 02. Aspect Ratio k c (p.7) 03. Screen Mute k d (p.7) k e 00 to 01 k f 00 to 64 06. Contrast k g 00 to 64 07. Brightness k h 00 to 64 04. Volume Mute 05.
6 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
EXTERNAL CONTROL DEVICE SETUP 7 01. Power (Command: k a) ►► To control Power Off of the set. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To Show Power On. (Works TV is On Only) Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][01][x] * Similarly, if other functions transmit ‘FF’ data based on this format, Acknowledgement feedback presents status about each function. 02.
8 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 09. Tint (Command: k j) 14. Color(Colour) Temperature (Command: x u) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. ►► To adjust colour temperature. You can also adjust Color(Colour) Temperature in the PICTURE menu.
EXTERNAL CONTROL DEVICE SETUP [Data 00][Data 01]: Channel Data Data 00 : High Channel data Data 01 : Low Channel data - 00 00 ~ 27 0F (Decimal: 0 ~ 9999) Data 05: Input Source (Analogue) - 00 : Terrestrial TV (ATV) - 01 : Cable TV (CATV) * Digital Terrestrial/Cable Data 00 : xx (Don't care) Data 02 : Input Source (Digital) - 10 : Terrestrial TV (DTV) - 20 : Terrestrial Radio (Radio) - 40 : Satellite TV (SDTV) - 50 : Satellite Radio (S-Radio) - 90 : Cable TV (CADTV) - a0 : Cable Radio (CA-Radio) [Data 01
10 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG [Data 01][Data 02]: Major Channel Number Data 01: High byte Channel Data Data 02: Low byte Channel Data - 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor/Branch Channel Number (Don’t care in Satellite) Data 03: High byte Channel Data Data 04: Low byte Channel Data Data 05 : Input Source (Digital/Satellite for Japan) - 02 : Terrestrial TV (DTV) - 07 : BS (Broadcasting Satellite) - 08 : CS1 (Communication Satellite 1) - 09 : CS2 (Communication Satell
EXTERNAL CONTROL DEVICE SETUP 23. Extended 3D(Command: x v) (only 3D models) (Depending on model) (Depending on model) ►► To change 3D option for TV. ►► To change 3D mode for TV.
