32LV570H 40LV570H 43LV570H 49LV570H 55LV570H 65LV570H ar y Lodging Guest Interactive Pro:Centric ® TVs Commercial Mode Setup Guide EXPERIENCED INSTALLER EZ-Manager Wizard pages 12 – 19 Custom Master TV Setup pages 33 – 35 Cloning Procedures pages 36 – 39 Pr el im in Note: Selected features shown in this guide may not be available on all models. © Copyright 2017 LG Electronics U.S.A., Inc. P/N: 206-4317 (Draft A.
For Customer Support/Service, please call: 1-888-865-3026 The latest product information and documentation is available online at: www.lg.com/us/business MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No._______________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 26. Keep the product away from direct sunlight. 21. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below. 27. When mounting a TV on the wall, make sure that none of the electrical cabling bears any of the weight of the TV. Install in accordance with the manufacturer’s instructions.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . . 6 – 9 Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pass-through Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commercial Mode Overview This document describes how to set up LV570H Pro:Centric ® TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or the embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider). These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU.
Commercial Mode Overview (Cont.) Installer Menu To create a Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 23 to 33 for information on accessing the Installer Menu and for detailed descriptions of the Installer Menu items.
Commercial Mode Overview (Cont.) When the TV CPU is configured with an FTG Channel Map, the CPU controls and restricts the tuning operation of the TV, and when the EBL is configured with an FTG Channel Map, the EBL controls and restricts the tuning operation of the TV. In these models, FTG Mode via CPU also provides the option to select either logical or physical tuning (see note below) during configuration.
Commercial Mode Overview (Cont.) While the TV is in FTG Mode: • Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu items will be read-only. • FTG Mode via CPU configuration changes must be made using a “.tlx” file (typically edited in the FTG File Manager), while FTG Mode via EBL configuration changes must be made using the FTG Device Configuration Application.
Pro:Centric Operation Pro:Centric Interactive Menu Features LG’s Pro:Centric application enables guests to locate and select television entertainment using an interactive channel guide, check the daily weather, and view hotel and surrounding amenities via custom billboards and points-of-interest maps. Pro:Centric application features include: • Portal and information screens/pages (including a “Welcome” page) that include branding logos. • An optional customized user interface (custom “skins”).
Pro:Centric Operation (Cont.) Pro:Centric Setup Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Server Admin Client User Guide. This document describes only those settings that must be specified on the TVs to enable Pro:Centric remote management and/or the Pro:Centric application.
EZ-Manager Wizard The primary purpose of the EZ-Manager Wizard is to guide you through the process (automated or manual) of configuring the essential Installer Menu items for Pro:Centric operation. The wizard will appear on the screen each time the TV is turned ON, until one of its configuration methods has been completed or the wizard is exited. Use the Installer Remote to make selections and complete each wizard step.
EZ-Manager Wizard (Cont.) From the Welcome screen, you have the following options: • To proceed with the EZ-Manager Wizard, use the arrow keys on the Installer Remote to select/ highlight Next, and then press OK. Then, continue to the “TV Configuration Options” section below. • To exit the wizard, but retain the use of the Pro:Centric remote management feature on this TV (i.e.
EZ-Manager Wizard (Cont.) Zone and Room Number Assignments You may complete one or more of the fields in the Zone, Label, and Room Number screen or leave them at their default settings (Zone) or blank (Label and Room Number), as desired; however, if you intend to use the Zoning feature on this TV, you MUST specify the appropriate value in the Zone field as described below. See also Reference section, “Using the TV Zoning Feature,” for further information.
EZ-Manager Wizard (Cont.) Configure Pro:Centric Settings Once you select “Next” from the TV Configuration Options screen, the Searching for Pro:Centric Server screen is displayed. Note: Select the “Back” button, where available, to check previous settings, as necessary. Z EZ-Manager Wizard 1 2 3 4 Searching for Pro:Centric Server... It may take 1 min 32 second(s). This step automatically searches for the Pro:Centric server.
EZ-Manager Wizard (Cont.) (Continued from previous page) EZ-Manager Wizard 1 2 3 4 Processing the Pro:Centric Configuration... Downloading the maintenance files takes several minutes. Please wait... 20% Retrieving files from data channel 75 Application files Maintenance files GEM app downloaded In progress...
EZ-Manager Wizard (Cont.) (Continued from previous page) Note: For remote management only, select Configuration Only. The TV will search for TV E-Z Installation data downloads; however, Pro:Centric application data will not be downloaded, i.e., Installer Menu item 098 PRO:CENTRIC will be set to 0.
EZ-Manager Wizard (Cont.) (Continued from previous page) 4. Once all fields are completed as required, you have two options: • To save the data entered and exit the wizard, use the arrow keys to select Exit and then press OK. In the subsequent pop-up confirmation window, select Save and Exit, and then press OK once more. The Pro:Centric application and/or E-Z Installation data will be downloaded to the TV at a later time.
EZ-Manager Wizard (Cont.) (Continued from previous page) • Ensure the USB device to be used has been formatted with FAT format. • When creating files to be downloaded, avoid using special characters (?, &, @, etc.) in filenames. • Refer to “Ez Download Utility” on pages 20 to 22 for further information on the Ez Download utility. • Refer to “Custom Master TV Setup” on pages 34 to 36 for information on creating a Clone (.
Ez Download Utility The Ez Download utility, available from the TV Manager, enables you to select multiple files at one time from the files loaded on a USB memory device. You may use this utility to download any one or all of the following to a TV: • One Clone or FTG Configuration (.tlx) file • One TV CPU software update • One PTC software update • One splash screen image Before You Begin • Ensure the USB device has been formatted with FAT format.
Ez Download Utility (Cont.) (Continued from previous page) 3. If the TV is currently in Pass-through Mode, you would like to transfer (import) a “.tlx” file to the TV via the Ez Download utility, and you intend to use the TV Zoning feature, assign the appropriate TV Zone # in the TV at this time. See Reference section, “Using the TV Zoning Feature,” for further information.
Ez Download Utility (Cont.) (Continued from previous page) 8. The fields at the right of the screen will change depending on the currently highlighted file. Select the appropriate option(s) for each file, as applicable. • For software and splash screen image files: The fields at the right of the screen show the TV software versions and any available Forced Update options.
Installer Menu Use the Installer Menu to set up, change, or view operational settings. This section describes how to access, use, and exit the Installer Menu from the TV itself. However, you should also refer to the Installer Menu descriptions in this document if you are configuring the TV CPU using an FTG Configuration (.tlx) file created using LG’s FTG File Manager software or configuring the EBL locally (.rml) or remotely (via FMA-LG102 / .fma) using the FTG Device Configuration Application software.
Installer Menu (Cont.) As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV models.
Installer Menu (Cont.) Installer Menu Items 000 through 071 Item Function 000 INSTALLER SEQ Value Range Default Value Brief Description of Function 0–3 0 Leave default set to 0. 001 POWER MANAGE 0–7 0 Selects the number of hours of inactivity allowed before the TV automatically turns itself OFF. Set to 0 to disable power management. 002 AC ON 0–3 0 Set to 1 to enable TV to turn ON when AC power is applied. Set to 2 or 3 to enable Instant ON when AC power is applied.
Installer Menu (Cont.) Installer Menu Items 073 through 122 Item Function 073 CH NOT AVBLE 075 REVERT CH 078 UPN MSB 079 UPN MSB-1 080 UPN MSB-2 081 UPN LSB 082 083 26 Value Range Default Value Brief Description of Function 0/1 0 If set to 1 and item 028 CH. OVERIDE is set to 0, a “CHANNEL NOT AVAILABLE” message is displayed if user attempts to direct tune a channel that is not included in the channel lineup.
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Energy saving feature. Determines the number of hours, in the range 1 to 7, of inactivity allowed, either at the TV control panel or from the remote, before the TV automatically turns itself OFF. If set to 0, Power Management is disabled.
Installer Menu (Cont.) 008 - MIN VOLUME (Minimum Volume) This function determines the minimum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is set to 63. It is recommended to set the same value on every TV.
Installer Menu (Cont.) 031 - POLL RATE MPI Communication Parameter. Selects poll rate for MPI. Step size of 16 ms. Changing from default may affect communication via MPI. 032 - TIMING PULSE MPI Communication Parameter. Sets baud rate for MPI. Step size of 4.3 uS. Changing from default may affect communication via MPI. 035 - HDMI1 ENABLE Set to 1 to enable HDMI 1 input in DTV Mode. Set to 2 to enable HDMI 1 input in PC Mode. Set to 0 to disable display panel HDMI 1 input.
Installer Menu (Cont.) 075 - REVERT CH (Revert to Start Channel) If set to 1 and loss of MPI communication occurs, TV automatically tunes to the specified Start Channel. Note: This item is not available in the Installer Menu when item 004 STRT CHANNEL is set to 255. 078 - UPN MSB (UPN Most Significant Byte) User programmable number, most significant byte readable by MPI command. Note: Not linked to serial number.
Installer Menu (Cont.) • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard. Note: See also Reference section, “RJP Model List & Input Autosensing Hierarchy.
Installer Menu (Cont.) 106 - ASP RATIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF. ASP. RATIO above. 107 - BANNER SELECT Selects the type of banner to display during channel change. Set to 1 for channel label display, plus channel information (full banner). Set to 0 for channel label display only (small banner). 116 - VIDEO MUTE EN (Video Mute Enable) Applicable for analog channels only.
Installer Menu (Cont.) If this item is set to 128 (OFF), the time at which a Data Channel Auto Search (item 119 set to 255) and/or an Instant ON update (item 002 set to 2 or 3) occurs is determined as follows: The TV initiates the search and/or checks for updates at 2:00 AM (if the TV clock is set) or after two hours of elapsed time from when AC power was applied (if the TV clock is not set).
Custom Master TV Setup This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in Pass-through Mode. All cloning (export and import) processes on the TV are performed via USB memory device / “.tlx” file. The Master TV Setup may be exported to a Clone (.tlx) file, which can then be used (i.e., imported) to configure either TVs that are to remain in Pass-through Mode or TVs that are to be configured for FTG Mode via CPU.
Custom Master TV Setup (Cont.) Custom Master TV Setup Procedure 1. Turn ON the TV. The next step depends on whether the EZ-Manager Wizard appears on the screen when you turn ON the TV: • If the wizard is displayed, the TV is in the required factory default state. Exit the wizard, and then continue with step 2. • If the wizard is not displayed, restore the TV to a factory default condition before continuing with this procedure.
Custom Master TV Setup (Cont.) (Continued from previous page) 4. Set up TV features. On-screen setup menus control the features of the TV. Press MENU SETTINGS on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Audio, Time, etc. options to the desired configurations. See “Clonable TV Setup Menu Features” list on page 34 and also notes below.
Cloning Procedures Cloning typically refers to the process of using a Master TV Setup to configure a Target TV. This section describes how to save (export) a Master TV Setup and then transfer (import) it to a Target TV using a USB memory device / Clone (.tlx) file. You can also create an FTG Configuration (.tlx) file using the FTG File Manager and then use the Import Clone File procedure to transfer the configuration to Target TVs.
Cloning Procedures (Cont.) (Continued from previous page) 6. Use the Up/Down arrow keys to select Export Clone File, and then press OK. 7. In the Export Clone File window, to differentiate this Clone file from other LV570H Clone files, you can use the Up/Down arrow keys to change the last five digits of the filename. Press OK when you are ready to continue. Export progress will be shown in a new window. Do NOT remove the USB device while exporting is in progress.
Cloning Procedures (Cont.) (Continued from previous page) • If a Clone (.tlx) file (exported Master TV Setup) contains an FTG Channel Map, the physical RF channels in the FTG Channel Map have been assigned logical channel numbers (see “Exporting a Clone File” above). When you import the Clone file with the FTG Channel Map on the Target TV(s), you will have the option to select either logical or physical channel tuning.
Cloning Procedures (Cont.) (Continued from previous page) 5. Press MENU SETTINGS on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode). 6. Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times to access the TV Manager.
FTG File Manager Utilities Overview As indicated in the introduction to this document, there are two separate and distinct methods for configuring LV570H TVs for FTG Mode of operation: one method is to configure the TV CPU for FTG Mode operation, while the other is to configure the TV EBL for FTG Mode operation. FROM A LOCAL CONFIGURATION STANDPOINT, EACH OF THESE METHODS IS MUTUALLY EXCLUSIVE. IF THE CPU IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG MODE.
FTG File Manager Utilities Overview (Cont.) (Continued from previous page) Note: To remove an individual item from the FTG Configuration List or the Setup Menu List, click on/ highlight the item to be removed, and then click the Remove Item button directly above the applicable “List” window. To clear both the current FTG Configuration List and Setup Menu List contents, click the Clear button in the List command section of the FTG File Manager main screen.
FTG File Manager Utilities Overview (Cont.) FTG File Manager Main Screen The FTG File Manager main screen enables you to compile, modify, and save FTG Configuration (.tlx) files. It also allows you to change the Zone assignment for each Installer Menu profile, if desired (see Reference section, “Using the TV Zoning Feature,” for further information). FTG CONFIGURATION LIST Data to be saved in FTG Configuration (.tlx) file. CLEAR/SAVE FTG Configuration and Setup Menu List options.
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Configuration Utility The FTG Channel Map Configuration Utility enables you to create, view, edit, and print a Logical Channel Map. EDIT/ADD MAP Click to open the FTG Channel Map Editor to create or edit an FTG Channel Map (see next page). PRINT MAP Click to display a printable FTG Channel Map Report. The report can also be exported as an HTML or Text file. Filename of opened FTG Configuration (.
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map. LOGICAL CHANNEL MAPPING Select a Logical Channel number. Then, assign the RF, Major, and Minor channel numbers to complete the mapping. CUSTOM CHANNEL LABELS/ICONS Enter custom labels and select icons by name on menu or by number. SET CHANNEL ATTRIBUTES Check/select Encrypted, OSD, or Blank Video.
FTG File Manager Utilities Overview (Cont.) FTG Installer Menu Configuration Utility CONFIGURATION SETTINGS Select tabs for categories of Installer Menu items to set up TV. Filename of opened FTG Configuration (.rml) file created using FTG Device Configuration Application. Notes: • The Pro:Centric tab enables you to set up Pro:Centric-specific parameters. Refer to the Free-ToGuest (FTG) File Manager User Guide for further information. • LAN and Hospital parameters are not applicable for these TV models.
IP Environment Setup The IP Environment Menu enables you to set up the network features of the TV. With the exception of Network Connection settings, the IP Environment settings are editable (with the Installer Remote) only if the TV is in Pass-through Mode and read-only when the TV is not in Pass-through Mode.
IP Environment Setup (Cont.) (Continued from previous page) The next Network Setting window will enable you to specify the IP and DNS configuration for this TV. Auto settings will be selected by default. Use the arrow keys to select the appropriate options, and specify the configuration data for the IP and DNS modes. When all fields are completed, select OK on the screen and press OK on the Installer Remote. Network Setting Select the IP setting mode.
IP Environment Setup (Cont.) Pro:Centric Setup Pro:Centric options enable you to configure the TV with the appropriate settings to connect to the Pro:Centric server. Use the Up/Down arrow keys on the Installer Remote to navigate between fields. 1. With the IP Environment Menu on display, use the arrow keys on the Installer Remote to select Pro:Centric. Then, press OK. 2. Select/highlight the Media Type field, and use the Left/Right arrow keys to select either RF or IP, as applicable.
IP Environment Setup (Cont.) (Continued from previous page) IP Configuration In the Server IP and Port Number fields, either key in or use the Left/Right arrow keys to select the appropriate values for the Pro:Centric server IP address and port number. The IP address must match the IPv4 multicast address and the port number must match the port number that is set in the Pro:Centric server.
Reference: Remote Jack Pack / TV Connections & Setup Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE to 1). See Installer Menu detailed descriptions for further information. 093 RJP AVAILABLE 001 TV Connections Caution: Make these connections ONLY after Master TV Setup and TV cloning procedures are complete.
Reference: Updating TV/PTC Software using a USB Memory Device This section describes how to update TV (CPU) and/or PTC software using the TV Manager “Update TV Software” and/or “Update PTC Software” option(s), respectively, though you may also use the Ez Download utility to update software, if desired. See “Ez Download Utility” on pages 20 to 22 for further information.
Reference: Downloading a Splash Screen Image using a USB Memory Device This section describes how to download a splash screen image using the TV Manager “Logo Image Download” option, though you may also use the Ez Download utility to download the splash screen image, if desired. See “Ez Download Utility” on pages 20 to 22 for further information. Splash Screen Image File Guidelines • The splash screen image must be a baseline (not progressive) JPEG. • The image should be no larger than 1 MB.
Reference: Power Consumption Settings The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 3 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 255). 32LV570H Item 099 Back Lighting (Static) 100 90 80 70 60 50 40 30 20 10 1 40LV570H Power Consumption (Watts) Percent Savings Power Consumption (Watts) Percent Savings Power Consumption (Watts) Percent Savings 26.0 24.4 23.5 23.0 22.2 21.3 20.5 18.3 15.6 13.1 10.
Reference: Power Consumption Settings (Cont.) 49LV570H Item 099 Back Lighting (Static) 100 90 80 70 60 50 40 30 20 10 1 55LV570H Power Consumption (Watts) Percent Savings Power Consumption (Watts) Percent Savings Power Consumption (Watts) Percent Savings 60.1 55.9 52.7 51.6 50.8 47.3 44.9 39.4 32.2 24.5 17.6 0% 7% 12% 14% 15% 21% 25% 34% 46% 59% 71% 83.6 76.6 72.4 69.9 66.7 62.9 59.5 50.1 37.9 27.4 16.6 0% 8% 13% 16% 20% 25% 29% 40% 55% 67% 80% 85.3 78.8 75.0 72.8 69.9 66.5 62.8 54.3 43.6 33.
Reference: TV Aux Input Configuration ENABLE DIRECT ACCESS Tuning * TV MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) Installer Menu DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STATUS TYPE 0x0D AUX SOURCE (R) Installer Menu Item 029 OLD OCV =0 Installer Menu Item 029 OLD OCV =1 Aux Input Input Mode Item Function Value Enable Bit Label Value Value Description 131-0 91-0 AV (Rear) CV 39 REAR AUX EN 1 1 Rear Video (Aux) 1 0 VIDEO VIDEO 92-0 HDMI2 91 HDMI2 ENABLE
Reference: b-LAN Setup & Overview The b-LAN module is internal to the TV. It allows hotel/institution head end equipment with b-LAN technology to communicate, via the institution’s RF distribution system, with the TV for configuration and control. Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port. The default value is 3—the b-LAN module is only powered when the TV is turned ON. See chart below.
Reference: FTG Mode via EBL (Local Configuration) The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV (EBL) connection. Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide for further information. FTG Device Configuration Application software is available online at: www.lg.com/us/business/display-solutions/ftg.
Reference: Auto Input(s) Sensing Feature This section provides detailed settings information for Installer Menu item 042 AUTO INPUTS. To disable auto-sensing for all available Aux inputs, set item 042 to 0. To enable auto-sensing for all available Aux inputs, set item 042 to 255. For specifications on all other available settings (i.e., settings for individual inputs), refer to the table on the following page.
Reference: Auto Input(s) Sensing Feature (Cont.
Reference: RJP Model List & Input Auto-sensing Hierarchy RJP Legacy Models • RJP-101M • RJP-110WBR • RJP-101ML • RJP-110S • RJP-110F • RJP-120G • RJP-110FW • RJP-120T • RJP-110W • RJP-201B/202B RJP Scaler Models • RJP-301B RJP Input Auto-sensing Hierarchy Priority Video Audio 1st (Highest) Digital Video In Audio In (3.5mm) 2nd PC Video In Audio In (L/R) 3rd Video In Digital Video In 206-4317 Draft A.
Reference: Restoring Factory Defaults on the TV(s) This section describes how to restore all factory defaults or just the Installer Menu factory defaults either on a single TV that is currently in Pass-through or FTG Mode or on multiple TVs that are currently in FTG Mode. Restore All Factory Defaults This section describes how to restore a single TV, regardless of its mode, to a factory default condition.
Reference: Using the TV Zoning Feature This section describes the TV Zoning feature available with the LV570H model TVs. The TV Zoning feature enables you to create localized configurations for TVs in selected locations, or “Zones,” within the installation environment, for example, a hotel lobby, fitness center, restaurant, etc. This feature is primarily intended for use when the TV is configured for FTG Mode via CPU operation.
Reference: Using the TV Zoning Feature (Cont.) Note: While a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one Zone. See also the FTG Channel Map Editor overview on page 45. At the same time, keep in mind that the TV Zone designations are not mutually exclusive.
Reference: Using the TV Zoning Feature (Cont.) (Continued from previous page) To change the TV Zone, navigate to the Zone field, and use the Up/Down arrow keys to specify the desired TV Zone # (0–8). • Label: Allows you to select a North, South, East, or West text label for this TV. Use the Up/Down arrow keys to select the applicable label. • Room Number: Allows you to specify the number of the room—up to 16 characters—in which the TV is located.
Reference: LV570H Rear and Side Jack Panels HDMI IN 1 Connection for HDMI/DVI output from external device. LAN Use for network connection (i.e., for Pro:Centric data). RJP Use Only Connection for Remote Jack Pack (RJP) Control cable. SPEAKER OUT LINE OUT (3.5 mm jack) Connect external audio (fixed speaker, variable speaker, or fixed line level [amplifier]) equipment. See Reference section, “External Stereo Speaker Setup,” for further information.
Reference: External Stereo Speaker Specifications The SPEAKER OUT / LINE OUT 3.5 mm stereo jack on the LV570H rear panel provides stereo speaker signal outputs (fixed speaker, variable speaker, or fixed line level [amplifier]) for external audio equipment. Set Installer Menu item 097 AUDIO OUTPUT as required in accordance with external audio equipment connected to the TV. Also, refer to the following diagram for pinout details. Caution: Do NOT insert a mono plug, as this may damage the TV.
Reference: Installer Remote Control Typical Key Functions The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated below shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV. Q.MENU (POWER) Turns the TV ON or OFF TV/DVD Select the remote’s operating mode: TV or DVD. INPUT TV Numbers (0 - 9) & DASH Use to enter a channel or program number.
Troubleshooting General Troubleshooting Some Quick and Easy Tips for Resolving Problems Installation Symptom Possible Cause(s) Possible Solution(s) Cannot direct enter channel number. (TV in Pass-through Mode) Installer Menu item 028 CH. OVERIDE is set to 0, i.e., disabled (recommended setting). If Installer Menu item 028 CH. OVERIDE is set to 0, only channels that are active in the TV’s channel lineup can be selected. Set CH. OVERIDE to 1 to allow access for direct keypad entry to all channels.
Troubleshooting (Cont.) Commercial Mode Check / FTG Operation Troubleshooting Commercial Mode Check Use this flowchart to determine whether the TV is currently in Commercial Mode. Press POWER on Installer Remote. TV turned ON? No TV connected to AC Power? No Plug into AC Power outlet. Yes Yes Bad TV Leave the TV set ON, and press MENU SETTINGS on the Installer Remote. Function Menu on display? No Press MENU SETTINGS repeatedly as if to access the Installer Menu.
Glossary of Terms b-LAN SONIFI Solutions, Inc. proprietary RF communication system used to configure/ control TV via RF distribution system. Channel Lineup Channels set in the TV memory, via Auto Tuning/manual editing. Cloning The process of capturing a Master TV Setup and transferring it to a Target TV using a USB memory device. Commercial Mode A mode of operation that provides a broad range of commercial TV features based on control (settings) provided by the PTC and/ or an MPI control device.
Document Revision History / Open Source Software Notice Document Revision History Date Description March 2017 Draft A.2: New document Product documentation is available online at: www.lg.com/us/business. Open Source Software Notice To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com.
For Customer Support/Service, please call: 1-888-865-3026 www.lg.com/us/business Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric and the “LG” logo are registered trademarks of LG Electronics Inc. b-LAN is a trademark of SONIFI Solutions, Inc. All other trademarks or registered trademarks are the property of their respective owners. © Copyright 2017 LG Electronics U.S.A., Inc. 206-4317 Draft A.
