Installation Manual

ManualsBrandsLG ManualsLED TVs43LX560H

206-4277

099 - BACK LIGHTING

Sets the TV screen brightness at power up. Default setting is 255.

• 1 - 100 Static Back Lighting

(1 = Dimmest picture, 100 = Brightest picture)

• 101 - 200 Dynamic Back Lighting

(101 = Dimmest picture, 200 = Brightest picture)

If set between 101 and 200, the TV automatically controls back

lighting depending upon the picture level of the current program. If

set to 255, back lighting is controlled via the Picture settings in the

TV setup menus.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals.

0 = Broadcast 1 = CATV 2 = HRC

3 = IRC 4 = Same as NTSC

103 - ATSC TUNE MODE

Sets ATSC tuning mode. Default set to 1 for Physical Channel

scan. Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL

Sets Minor Start Channel number at power up. 0 = NTSC. If not

0, number selected is the digital channel’s Minor Start Channel

number.

Note: This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 0 or 255.

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power off. Set to 0 to

retain default aspect ratio with power off. See item 096 DEF. ASP.

RATIO above.

116 - VIDEO MUTE EN (Video Mute Enable)

Applicable for analog channels only. If set to 1, video mutes

(blank screen) when no signal is present.

117 - FACT DEFAULT (Factory Default)

Set to 1 and press OK to restore the factory default settings of all

Installer Menu items. Once complete, the value returns to 0.

Caution: If set to 1, this clears all Installer Menu custom

settings and restores the factory default settings. It also

clears the channel lineup, including any assigned

channel icons and custom text labels.

Note: See also Reference section, “Restoring Factory Defaults on

the TV(s),” for further information.

119 - DATA CHANNEL

Set to 0 to disable. Set from 1 to 135 to match the RF channel

number that will be used by the Pro:Centric server as its data

channel. If left at the default value (255), the TV’s Data Channel

Auto Search feature will be enabled (see additional information

below). *

Data Channel Auto Search feature: When this item is set to 255

(default) once every 24 hours, the TV will initiate a search of 10

predened channels (10, 20, 30, ... 100) and then, if necessary,

perform a complete search of the RF channels (1 to 135) in an

attempt to nd the RF channel used by the Pro:Centric server as

its data channel. If the Pro:Centric RF channel is found, the DATA

CHANNEL value will be changed from 255 to match the server’s

RF channel number. The time at which the Auto Search occurs

depends on the setting of item 121 P:C RF WAKE HR. See item

121 description for further information.

Note: Pro:Centric updates are downloaded from the Pro:Centric

server to the TV when the TV is turned OFF. While Pro:Centric

updates are in progress, it is not possible to turn ON the TV.

Note: The Data Channel is automatically set to “253” if Media

Type is set to “IP” either in the EZ-Manager Wizard or in the IP

Environment / Pro:Centric Menu on the TV (see “EZ-Manager

Wizard” on pages 12 to 18 or “Pro:Centric Setup” on pages 47

to 48, respectively) or if Installer Menu item #119 Data Channel

is set to “IP Address” in the FTG File Manager, which is used to

congure TV CPUs for FTG Mode operation. It is not possible to

change the value to “253” directly in the Installer Menu.

121 - UPDATE TIME HR

Based on the settings of this item and item 122 UPDATE TIME MN,

the Wake For Update feature wakes the TV once daily to check for

and, if applicable, download updates from the Pro:Centric server.

Set the Wake For Update hour from 0 to 23. This item uses the

24-hour clock format. The value “128” (default) is displayed as

“OFF.” Directly entering 128 resets the default value (OFF) for this

item, though note that this setting does not mean the TV will not

initiate update events—see additional information below.

Under standard TV OFF/ON operating conditions (i.e., item 002 AC

ON is set to 0), a Wake For Update event occurs when the TV is

OFF and causes the TV’s CPU to temporarily turn ON, perform the

update cycle, and then turn back OFF, all while the TV appears to

be OFF. If item 002 AC ON is set to 2 or 3 for Instant ON, then the

TV’s CPU is always ON and Wake For Update occurs when the TV

is in its Muted ON state (i.e., the TV only appears to be OFF). The

Wake For Update event causes the TV’s CPU to reboot in order

to perform the update cycle and then return to its Muted ON state.