Installation Manual

32
206-4279
Installer Menu (Cont.)
030 - ACK MASK
MPI Communication Parameter. When set to 1, enables ACK
feature of MPI.
031 - POLL RATE
MPI Communication Parameter. Selects poll rate for MPI. Step
size of 16 ms. Changing from default may affect communication
via MPI.
032 - TIMING PULSE
MPI Communication Parameter. Sets baud rate for MPI. Step
size of 4.3 uS. Changing from default may affect communication
via MPI.
035 - HDMI1 ENABLE
Set to 1 to enable HDMI 1 input in DTV Mode. Set to 2 to enable
HDMI 1 input in PC Mode. Set to 0 to disable display panel HDMI
1 input.
Note: This setting is ignored if item 093 RJP AVAILABLE is set
to 1.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component input jacks. Set
to 0 to disable display panel rear Component input jacks.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear Aux (AV) input. Set to 0 to
disable display panel rear Aux (AV) input.
041 - SIMPLINK EN
Set to 0 to disable the SIMPLINK feature. Set to 1 to enable
SIMPLINK functionality (does not enable remote control access to
the SIMPLINK Menu).
Note: When both this item and item 042 AUTO INPUTS are
enabled in the Installer Menu, HDMI inputs will be detected by
SIMPLINK, but the Auto Input(s) Sensing Feature will not function.
042 - AUTO INPUTS
Determines the Aux inputs for which auto-sensing is enabled. Set
to 0 to disable auto-sensing for all available inputs. Set to 255 to
enable auto-sensing for all available inputs. For information on
options for individual input settings, see Reference section, “Auto
Input(s) Sensing Feature.”
Note: In order for auto-sensing to be enabled for an input, that
input must also be enabled in the Installer Menu. For example, to
enable auto-sensing for HDMI 1, item 035 HDMI1 ENABLE must
also be set to 1 or 2. Also, see note above regarding TV operation
when both this item and item 041 SIMPLINK EN are enabled.
Note: When this item is enabled in the Installer Menu, item 093
RJP AVAILABLE is automatically set to 0.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting Aux source. When turned ON, the TV will tune to
starting Aux source if item 004 STRT CHANNEL is set to 0.
1 = AV 3 = HDMI 1 5 = HDMI 2
6 = Component 7 = HDMI 3 255 = Last Aux
Note: Above is applicable only if all Aux sources are enabled.
Note: This item is not available in the Installer Menu unless item
004 STRT CHANNEL is set to 0.
047 - AUX STATUS
Set to 1 for MPI Aux source to be reported as a channel number
instead of channel 0. Set to 0 to disable Aux identication change.
Controls MPI status channel response for Aux inputs.
049 - DIS. AUDIO M. (Disable Audio Menu)
Determines the availability of the Sound Out (Audio) Menu in the
TV menus. Also determines the default Audio Mode when TV is
turned ON. See the table below and set as required.
Value
Sound Out
Menu Status
Default Audio Mode at TV
Turn ON
0 (default) Enabled Internal TV Speaker
1 Disabled Internal TV Speaker
2 Enabled External Speaker (optical or HDMI)
3 Disabled External Speaker (optical or HDMI)
4 Enabled LG Sound Sync (optical)
5 Disabled LG Sound Sync (optical)
6 Enabled LG Sound Sync (BT wireless)
7 Disabled LG Sound Sync (BT wireless)
8 Enabled Internal TV Speaker + Audio Out (optical)
9 Disabled Internal TV Speaker + Audio Out (optical)
Note: If a SIMPLINK-enabled device is connected to the TV
and item 041 SIMPLINK EN is set to 1 (enabled), the SIMPLINK
device Audio Mode will have priority over the setting of this item
when the TV is turned ON.
Note: When this item is set to 6 or 7, the Bluetooth Sound Sync
Media Share feature is not available. If Bluetooth Sound Sync is
currently enabled in the IP Environment / Media Share Menu, it
will be disabled.
053 - DIS. CH-TIME (Disable Channel-Time Display)
Set to 1 to disable the TV’s native Channel-Time display when a
custom channel label/channel information will be provided by the
MPI command. Set to 0 to enable the TV’s native Channel-Time
display.