使用指南 這是安裝在電視上的「使用指南」。 為提升品質,本指南可能隨時變更,恕不事先通知。
❐❐檢視節目資訊 滾輪(OK) ➾ 資訊 顯示目前節目和/或目前時間等資訊。 ✎✎ 顯示的圖片可能與您的電視不同。 目前時間 1 月 1 日 六 12:02 上一個/下一個 下午 10:00 頻道切換 節目表 下午 10:00 節目名稱或外部裝置名稱 節目的詳細資訊 (適用於數位廣播)
❐❐設定喜愛頻道節目 HOME ➾ 設置 ➙ 設定 ➙ 頻道編輯 1 2 3 4 移至所需的節目,然後按下滾輪 (OK) 按鈕。隨即會選擇該節目。 按下設為我的最愛。 選擇想要的 [喜愛頻道節目 群組]。 選擇確認。[喜愛頻道] 即設定完成。 ❐❐使用喜愛頻道 HOME ➾ 節目清單 隨即出現 [節目清單]。從 [數位電視節目列表] A 至 D 中,選擇想要的預設 喜愛頻道節目。
HOME ➾ 節目導覽 [僅適用於數位模式] 取得節目與播出時間的相關資訊。 取得節目資訊及預約檢視 / 錄影。 [顯示的圖片可能與您的電視不同。] 節目導覽 所有 今日 1/2 頁 2011.10.
❐❐設定自動頻道記憶 HOME ➾ 設置 ➙ 設定 ➙ 自動頻道記憶 自動調整頻道。 ✎✎ 除非正確連接天線/纜線,否則無法正確註冊頻道。 ✎✎ 自動頻道記憶只會設定目前廣播的頻道。 ✎✎ 若開啟系統鎖定,畫面會出現詢問密碼的快顯視窗。
❐❐手動設定頻道 HOME ➾ 設置 ➙ 設定 ➙ 手動頻道調整 手動調整調整和儲存結果。 對於數位廣播,可檢查訊號強度等狀態。
❐❐編輯頻道 HOME ➾ 設置 ➙ 設定 ➙ 頻道編輯 編輯已儲存的頻道。 將所選頻道設為喜愛頻道、頻道鎖定/開啟、略過頻道等。
HOME ➾ 設置 ➙ 影像 ➙ 畫面比例選擇 選擇螢幕畫面比例。 16:9 調整影像大小以符合螢幕寬度。 點對點掃瞄 以原始大小顯示視訊影像,影像邊緣不會被截斷。 ✎✎ 在 DTV/HDMI/Component (超過 720p) 模式中,可使用 點對點掃描。 ✎✎ 在 DTV (超過 576p) 模式中,僅澳洲可使用點對點掃 瞄。 原始比例 當電視接收到寬螢幕訊號時,會自動變更為影像格式廣 播。
全螢幕 當電視接收到寬螢幕訊號時,會讓您以線性比例對畫面進 行水平或垂直調整,使影像填滿整個螢幕。 全螢幕模式支援 4:3 與 14:9 視訊,透過 DTV 輸入時無任何 視訊失真。 ✎✎ 在 DTV 模式中,可使用全螢幕功能。 4:3 將影像大小調整為先前的標準 4:3。 14:9 您可以觀看 14:9 的影像格式,或以 14:9 模式觀看一般電視 節目。 14:9 畫面的觀賞方式與 4:3 畫面相同,但會向上及 向下移動。 放大 調整影像大小以符合螢幕寬度。 影像的上下部分可能會截 斷。 電影模式 若要以正確的比例放大影像,請選擇 [電影模式]。
✎✎ 檢視外部裝置時,這些情況可能會導致殘像: - 有固定字幕 (例如網路名稱) 的視訊 - 長時間使用 4:3 畫面比例模式 請謹慎使用這些功能。 ✎✎ 可用的影像大小可能因輸入訊息而異。 ✎✎ HDMI/RGB-PC 輸入的螢幕畫面比例僅適用 4:3 和 16:9。
❐❐在 PC 輸入模式中調整影像 HOME ➾ 設置 ➙ 影像 ➙ 畫面 在 RGB-PC 模式中調整影像。 設定想要的解析度。 解析度 ✎✎ 只有 PC 解析度設為 1,024 x 768、1,280 x 768 或 1,360 x 768 時,才能選擇解析度。 自動設定 最佳化影像。 位置 / 大小 / 如果畫面大小或位置失真,使用者可以直接調整畫面大小 相位 及位置。 重新設定 在 PC 輸入模式上重新設定對影像設定所做的所有變更。
❐❐設定電腦解析度 1 在電腦的桌面上按一下滑鼠右鍵,並選擇「內容」。 2 按一下「設定」並參閱支援的格式以設定解析度。 3 在設定視窗上選擇「進階 → 顯示器 → 顯示器設定」。 參閱支援的格式以 選擇最佳垂直頻率。 ✎✎ 在 PC 模式上,1,920x1,080 解析度可呈現最佳的影像品質。 ✎✎ 解析度設定會因電腦類型而異。
❌❌支援的格式 PC 輸入模式 HDMI-PC / RGB-PC HDMI-PC 解析度 水平頻率 (KHz) 640x350 720x400 640x480 800x600 1,024x768 1,152x864 1,360x768 1,920x1,080 1,280x1,024 31.468 31.469 31.469 37.879 48.363 54.348 47.712 67.5 63.981 垂直 頻率 (Hz) 70.09 70.08 59.94 60.31 60.00 60.053 60.015 60.00 60.
HOME ➾ 快速選單 ➙ AV 模式 針對不同的 AV 模式設定最佳影像 / 音效。 關 採用影像 / 音效選單中的設定值進行操作。 劇院/ ꔧ 劇院 針對電影最佳化影像及音效設定。 遊戲 針對遊戲最佳化影像及音效設定。 ✎✎ ꔧ [視型號而定] THX (Thomlinson Holman’s Experiment) 是一項由 George Lucas 和 Thomlinson 所創立的影音認證標準。 通過 THX 認證的顯示器,其畫面 品質在硬體和軟體方面皆超越顯示器的標準規格。
❐❐使用畫面精靈調整影像 HOME ➾ 設置 ➙ 影像 ➙ 畫面精靈 不需透過昂貴的模式裝置或藉助專家協助,只要使用遙控器並遵照畫面精 靈的指示,即可校正和調整以獲得最佳影像品質。 遵照指示以取得最佳影像品質。
❐❐選擇影像模式 HOME ➾ 設置 ➙ 影像 ➙ 影像模式 根據觀賞環境或節目選擇最佳的影像模式。 智慧型感測器 明亮 標準 偵測周圍照明並自動調整電視的亮度等級以減少耗電 量。 自動調整亮度、銳利度、色濃度或彩度以獲得最佳 影像品質。 提高對比、亮度和銳利度以顯示逼真鮮明的影像。 採用標準的對比、亮度和銳利度等級來顯示影像。
劇院 / ꔧ 劇 院 遊戲 ꕋ 專家 顯示已針對電影或遊戲最佳化的影像。 [ꔧ 劇院 : 視型號而定] 這是用來調整影像品質的選單,可讓專家和達人欣賞最 佳電視畫面。 此選單通過 ISF 認證,供影像調整專家使 用 (只有經 ISF 認證的電視機才能使用 ISF 標誌)。 ISFccc:Imaging Science Foundation Certified Calibration Control ✎✎ 可用的影像模式範圍可能會隨輸入訊號而異。 ✎✎ ꕋ 專家模式供影像調整專家使用特定影像進行控制及微調。 如果是正 常影像,效果可能並不顯著
❐❐微調影像模式 HOME ➾ 設置 ➙ 影像 ➙ 影像模式 ➙ 背光 / 對比 / 亮度 / 銳利度 / 色濃度 / 彩度 / 色溫 首先選擇您要的影像模式。 背光 變更 LCD 面板的亮度即可調整顯示亮度。 對比 調整畫面明亮和陰暗區域之間的差異。 亮度 調整畫面整體亮度。 銳利度 調整明亮和陰暗區域之間的邊框銳利度。
色濃度 將畫面色彩調暗或調暗。 彩度 調整紅/綠色彩平衡。 色溫 將整體色調調整為暖色系或冷色系。 ✎✎ 詳細項目的調整範圍可能會因輸入訊號或其他影像設定而異。
❐❐設定進階控制 HOME ➾ 設置 ➙ 影像 ➙ 影像模式 ➙ 進階控制/ 專業控制 針對每個影像模式調校畫面,或是針對特殊畫面調整影像設定。 首先選擇您要的影像模式。 動態對比度 依據影像亮度將對比調整至最佳等級。 動態色彩 調整色彩,讓影像色彩看起來更自然。 Clear White 增強畫面的白色,使影像更為明亮銳利。
偏好色彩 膚色:膚色色譜可以各別設定成採用使用者定義的膚 色。 草地色:自然色譜 (草地、山丘等) 可供各別設定。 天空色:天空色可供各別設定。 超級解析度 將含有模糊或不清楚影像的區域加以改善,提供清晰的 影像品質。 Gamma 根據與輸入訊號有關的影像訊號輸出,設定級配曲線。 色域 邊緣強化功能 xvYCC 彩色濾光片 專業模式 選擇可以表現的色彩範圍。 視訊中的邊緣顯示更清晰、突出,但卻自然。 [視型號而定] 呈現更豐富的色彩。 過濾 RGB 色彩中的特定色譜,以精確微調色彩飽和度 與色調。 用於專業調整的模式。
白平衡 視需要調整畫面的整體色調。 在「專業」模式中,您可透過「方法 / 模式」等項目進行詳 細微調。 色彩管理系統 專家可使用此功能,利用六種顏色 (紅/綠/藍/青/洋 紅/黃) 的測試模式來調整色彩,而不會影響其他色域。 如果是正常影像,調整後可能不會產生顯著的色彩變 化。 ✎✎ 詳細項目的調整範圍可能會因輸入訊號或其他影像設定而異。
❐❐設定其他影像選項 HOME ➾ 設置 ➙ 影像 ➙ 影像模式 ➙ 影像選項 調整詳細的影像設定。 雜訊抑制 MPEG 雜訊降低 黑階設定 電影模式 保護眼睛/ 智慧護眼功能 減少視訊中的畫面雜訊。 減少壓縮數位視訊所產生的雜訊。 使用畫面的暗度 (黑階設定) 來調整畫面的明暗度,以配 合影像輸入的黑階。 最佳化為適合觀看電影的畫面。 調整畫面亮度,避免眼睛眩光。 [智慧護眼功能 : 視型號而定]
❐❐重設影像模式 HOME ➾ 設置 ➙ 影像 ➙ 影像模式 ➙ 影像重新設定 重設使用者自訂的值。 每個影像模式都會重設。 選擇您要重新設定的影像模式。
HOME ➾ 設置 ➙ 影像 ➙ 自動影像選擇 ➙ 圖片選項 ➙ TruMotion 修正影像以顯示更流暢的動作序列。 柔和度 清除 Clear Plus 使用者 De-Judder/De-Blur 值設成 3。 De-Judder/De-Blur 值設成 7。 選擇清晰時,畫面看起來更清楚。 ✎✎ 3D 模式中無法選擇 Clear Plus。 可手動設定 De-Judder/De-Blur。 • De-Judder:此功能可調整畫面的顫動現象。 • De-Blur:此功能可調整和去除畫面的模糊現象。
HOME ➾ 設置 ➙ 影像 ➙ 自動影像選擇 ➙ 圖片選項 ➙ LED 本機區域 控制 在影像上,提高明亮區域的亮度和降低陰暗區域的亮度,藉此將對比度調 到最高並將模糊程度降至最低,同時還能減少耗電量。 關 低 正常 高 關閉 [LED 本機區域控制]。 呈現自然的黑色調。 此設定適合觀看電影時使用。 比起低設定,可進一步加深黑色調。 此設定適合觀看一般電 視時使用。 比起正常設定,可進一步加深黑色調,呈現更清晰的影像。 最適合在光線明亮的區域中觀看時使用。 ✎✎ 將 LED 本機區域控制設成正常 / 高可降低耗電量。
❐❐使用音效模式 HOME ➾ 設置 ➙ 音效 ➙ 音效模式 將電視音效最佳化為選取的音效模式。 標準 適用於所有類型的視訊 音樂 / 劇院 / 運動 / 為特定類別設定最佳音效。 遊戲 以豐富的低音和清晰的高音,呈現出明顯不同的聲 清晰 音。 使用者設定 利用使用者等化器調整至您要的音量。
❐❐微調音量 HOME ➾ 設置 ➙ 音效 ➙ 使用者等化器 首先在使用者設定中設定音效模式。 100 Hz / 300 Hz / 1 kHz / 手動調整音效頻帶來設定 EQ。 3 kHz / 10 kHz 重新設定 重新設定由使用者變更的等化器值。
❐❐設定音量模式 HOME ➾ 設置 ➙ 音效 ➙ 音量模式 設定音量控制的各種模式。 自動音量平衡 音量控制 將自動音量平衡設成開。 當選按不同的節目頻道時,便 會自動為每個節目不同的音量輸出進行調整,以方便觀 賞電視節目。 使用單一音量曲線可能會造成沒有聲音或聲音太大 (視環 境而定)。 視時段 (白天/晚上) 調整音量大小。
❐❐使用 Sound Optimizer 功能 HOME ➾ 設置 ➙ 音效 ➙ Sound Optimizer 可針對自訂的電視安裝方式最佳化音效。 正常 壁掛安裝型 直立型 一般音效模式。 針對壁掛安裝型的電視最佳化音效。 針對直立安裝型的電視最佳化音效。
❐❐使用虛擬環繞音效 HOME ➾ 設置 ➙ 音效 ➙ 虛擬環繞音效 LG 的專利音效處理技術可讓兩個揚聲器創造出類似 5.
❐❐同步音效與視訊 HOME ➾ 設置 ➙ 音效 ➙ AV 同步 當視訊和音效不相配時,直接進行同步處理。 若您將 AV 同步設成開,您可將音效輸出 (電視揚聲器或 SPDIF) 調整為畫面 影像。 電視揚聲器 SPDIF 調整電視內部揚聲器的音效同步。 「-」按鈕可加快音效輸出,「+」按鈕則可將音效輸出調得比 預設值慢。 (Sony Philips Digital InterFace) 針對連接到數位音效連接器 的揚聲器調整其音效同步。 「-」按鈕可加快音效輸出,「+」按鈕則可將音效輸出調得比 預設值慢。
Bypass 輸出廣播訊號或外部裝置的音訊,而無音效延遲。 音訊 可能會比視訊早輸出,因為將視訊輸入處理至電視需要時 間。 ❐❐使用 ARC 模式 HOME ➾ 設置 ➙ 音效 ➙ 音效設定 ➙ ARC 模式 外部音效裝置可透過高速 HDMIⓇ 纜線連接到輸出 SPDIF,不需透過額外的 光纖音訊纜線。 使用 SIMPLINK 介面。 對於支援 ARC (音效回傳頻道) 的外部裝置,請將其連接至 HDMI(ARC) 連接 埠。
關 開 即使所連接之支援 ARC 的外部音效裝置電源已開啟,音效輸出仍不 會透過外部音效裝置的揚聲器自動進行處理。 若支援 ARC 的外部音效裝置電源已開啟,音效輸出會透過外部音效 裝置的揚聲器自動進行處理。 對於 SIMPLINK,請參閱「一般 → 控制外部裝置」。 ✎✎ 連接外部裝置時,請連接到僅限 ARC 的端子。 ✎✎ 連接外部裝置時,請使用高速 HDMIⓇ 纜線。 ✎✎ 使用具備 ARC 功能的協力廠商裝置可能會導致功能失常。
❐❐調整音效平衡 HOME ➾ 設置 ➙ 音效 ➙ 音效設定 ➙ 平衡 調整左/右音效平衡。
❐❐使用電視揚聲器 HOME ➾ 設置 ➙ 音效 ➙ 音效設定 ➙ 電視揚聲器 透過連接到電視的外部音效裝置的揚聲器 (如家庭劇院設備) 聆聽時,電視 揚聲器可能會關閉。 如果有連接到 SIMPLINK 的家庭劇院裝置,將電視揚聲 器設成關則可自動開啟家庭劇院設備。 關 開 電視揚聲器不會播放音效。 透過連接電視的外部音效裝置揚聲器播放電視音效。 ✎✎ 透過外部裝置上的旋鈕調整音量。 透過電視的內部揚聲器播放電視音效。
❐❐使用數位音效輸出 HOME ➾ 設置 ➙ 音效 ➙ 音效設定 ➙ 數位音效輸出 設定 [數位音效輸出]。 項目 自動 PCM 音效輸入 MPEG Dolby Digital Dolby Digital Plus HE-AAC 全部 數位音效輸出 PCM Dolby Digital Dolby Digital Dolby Digital PCM
❐❐DTV 音效設定 HOME ➾ 設置 ➙ 音效 ➙ DTV 音效設定 [視型號而定] 當輸入訊號中含有不同類型的音效時,此功能可讓您選擇所需的音效類 型。 若設成自動,搜尋順序為 HE-AAC → Dolby Digital+ → Dolby Digital → MPEG, 且會從找到的第一個音效格式產生輸出。 ✎✎ 僅限於義大利,順序為 HE-AAC → Dolby Digital+ → MPEG → Dolby Digital。 ✎✎ 僅限於紐西蘭,順序為 Dolby Digital+ → Dolby Digital → HE-AAC → MPEG。 ✎✎ 若選取的音效格式不受支援,則可能會使用其他音效格式進行輸出。
❐❐選擇外部輸入 HOME ➾ 輸入清單 選擇外部輸入。 輸入清單 選擇揚聲器。 電視揚聲器 選擇輸入。 TV AV Component HDMI1 HDMI2 HDMI3 更改裝置名稱 SimpLink 設定 設定 SIMPLINK。 編輯連接到外部端子的外部裝置名稱。
❐❐使用 SIMPLINK SIMPLINK 這個功能可讓您只要使用電視遙控器透過 SIMPLINK 選單,就能便 利地控制和管理各種多媒體裝置。 1 使用 HDMI 纜線,連接電視的 HDMI IN 端子與 SIMPLINK 裝置的 HDMI 輸出端子。 如為具備 SIMPLINK 功能的家庭劇院裝置,請先連接 HDMI 端子 (方法同上),然後使用光纖纜線連接電視的光纖數位音效輸出和 SIMPLINK 裝置的光纖數位音效輸入。 2 選擇 HOME ➾ SIMPLINK。 隨即出現 SIMPLINK 選單視窗。 3 在 [SIMPLINK] 選單視窗中,選擇設定 SIMPLINK。 隨即出現 [SIMPLINK] 設 定視窗。 4 在 SIMPLINK 設定視窗中,將 SIMPLINK 設成開。 5 關閉 [SIMPLINK] 設定視窗。 6 從HOME ➾ SIMPLINK 選擇要控制的裝置。
✎✎ 此功能只能在標有 SIMPLINK 標誌 ( 確認外部裝置標有 SIMPLINK 標誌。 ) 的裝置上使用。 ✎✎ 若要使用 SIMPLINK 功能,您必須使用高速 HDMIⓇ 纜線 (具備 CEC (消費 性電子產品控制) 功能)。 高速 HDMIⓇ 纜線連接 13 號針,以供在裝置之 間交換資訊。 ✎✎ 開啟或選擇具備家庭劇院功能之裝置的媒體,查看揚聲器是否切換至劇 院揚聲器。 ✎✎ 連接光纖纜線 (另售) 以使用劇院揚聲器。 ✎✎ 切換為外部輸入會造成使用 SIMPLINK 的裝置停止運作。 ✎✎ 使用具備 HDMI-CEC 功能的協力廠商裝置可能會導致功能失常。
❌❌SIMPLINK 功能說明 直接播放 立即在電視上播放多媒體裝置。 透過 SIMPLINK 選單選擇所需裝置,以便從電視畫面立 選擇多媒體裝置 即控制該裝置。 光碟播放 使用電視遙控器管理多媒體裝置。 關閉所有裝置的 若 SIMPLINK 設定中的自動開機功能設定為開,則關閉 電源 電視會同時關掉所有 SIMPLINK 連線裝置的電源。
同步電源開啟 揚聲器 如果在 SIMPLINK 設定中將自動電源功能設為開,開啟 電視時也會開啟 SIMPLINK 裝置。 選擇家庭劇院裝置的揚聲器或電視的揚聲器。
HOME ➾ 設置 ➙ 影像 ➙ 節能模式 透過調整畫面亮度的方式來降低耗電量。 自動節能 關 最小節能 / 正常 節能 / 最大節能 螢幕關閉 電視感應器可偵測周圍光線,並自動調整螢幕亮度。 • 最低亮度:選擇在微弱周圍光線下的螢幕最小亮 度。 • 訊號感應強度:選擇電視在收視環境中的亮度範 圍。 關閉 [節能模式]。 套用預先設定的 [節能模式]。 關閉螢幕畫面,只播放聲音。 按遙控器上的任何按鈕,即可重新開啟畫面。
❐❐使用睡眠關機 HOME ➾ 設置 ➙ 時間 ➙ 睡眠關機 在經過指定的分鐘數後關閉電視。 若要取消睡眠關機,請選擇關。
❐❐設定目前時間 HOME ➾ 設置 ➙ 時間 ➙ 時間設定 在觀看電視的同時查看或變更時間。 自動 手動 將電視時間設定與電視台傳來的數位時間資訊保持同步。 若自動設定與目前時間不符,可手動設定時間和日期。
❐❐將電視設定為自動開啟或關閉 HOME ➾ 設置 ➙ 時間 ➙ 預約開機/預約關機 設定預約開/關機時間。 對重複選項選擇關,以停止預約開機/預約關機。 ✎✎ 若要使用預約開機/預約關機,請正確設定目前的時間。 ✎✎ 即使預約開機功能已開啟,電視屆時仍會在未按下任何按鈕的 120 分鐘 後自動關閉。
❐❐設定密碼 HOME ➾ 設置 ➙ 鎖定 ➙ 設定密碼 設定或變更電視密碼。 ✎✎ 初始密碼設定為「0000」。
❐❐系統鎖定 HOME ➾ 設置 ➙ 鎖定 ➙ 系統鎖定 透過鎖定節目或外部輸入,僅允許觀看特定節目。 首先請將系統鎖定設成開。 鎖定頻道 輸入鎖定 封鎖兒童不宜的特定節目。 ✎✎ 必須輸入密碼才能切換到鎖定的頻道。 封鎖選取的輸入。
HOME ➾ 設置 ➙ 選項 ➙ 語言 選擇顯示在螢幕上的 [選單語言] 和 [音效語言]。 選單語言 選擇顯示文字的語言。 音效語言 [僅限數位模式] 在觀看包含數種音效語言的數位播出時,可以選擇您需 要的語言。 字幕語言 [僅限數位模式] 在播放兩種或多種字幕語言時,您就可以使用 [字幕] 功 能。 ✎✎ 如果選擇的語言並未播放字幕資料,則會顯示預設語 言字幕。 語音搜尋語言 選擇要進行語音搜尋的語言。 ✎✎ 只有採用語音搜尋的機型可支援此設定。
❐❐設定聽力受損人士字幕 HOME ➾ 設置 ➙ 選項 ➙ 聽力受損人士字幕 此功能適用於聽覺受損人士。 如果設為開啟,會依預設顯示字幕。
❐❐註冊神奇遙控器 若要使用神奇遙控器,請先與您的電視進行註冊。 使用前請先依照下列指示註冊神奇遙控器。 1 開啟電視並等待約 10 秒,然後將遙控器指向電視,按下滾輪(OK) 按鈕。 2 遙控器會自動註冊,註冊完成訊息將出現在電視螢幕上。 ✎✎ 如果神奇遙控器註冊失敗,請關閉電視並再試一次。
❐❐取消註冊神奇遙控器 1 同時按下 HOME 和 BACK 按鈕約 5 秒。 2 將遙控器指向電視,然後按下滾輪(OK) 按鈕約 5 秒。 ✎✎ 將遙控器指向電視的同時按下 BACK 按鈕約五秒鐘,以重新設定並取消 註冊遙控器。
❐❐設定神奇遙控器的指標 HOME ➾ 設置 ➙ 選項 ➙ 指標 設定顯示在電視螢幕上的指標速度和形狀。 速度 設定指標的移動速度。 形狀 從各種選項中選擇指標形狀。 大小 選擇指標的大小。 自動游標 對齊 設為開。 如果指標與遙控器所指的實際方向之間有任何失準 情形,請左右移動神奇遙控器以重新對齊。 指標會自動重新 對齊中心,使其更易於控制。
✎✎ 指標一段時間未使用後即會消失。 當指標從畫面上消失,左右搖晃神奇 遙控器。 指標則會再次出現。 ✎✎ 如果您在移動畫面上的指標時按下導覽按鈕,指標會消失,神奇遙控器 就會像一般遙控器般作用。 ✎✎ 有效使用距離為 33 英呎 (10 公尺)。 從更遠的距離使用遙控器,或有阻 礙物擋住視線時,可能會導致功能失常。
✎✎ 鄰近的電子裝置可能會造成通訊干擾。 微波爐和無線 LAN 等裝置與神 奇遙控器使用相同的頻率範圍 (2.
❐❐使用圖案手勢功能 在正常視訊畫面上,按下滾輪(OK) 按鈕,對著螢幕畫出圖案。 上一個頻道:返回上一個頻道。 最近觀看過的頻道清單:顯示最近觀看過的頻道。 ✎✎ 特定視窗開啟時,可能無法使用該清單。
❐❐設定電源指示 HOME ➾ 設置 ➙ 選項 ➙ 待機光源 開啟/關閉電視前面板的待機光源。 ❐❐變更電視模式 HOME ➾ 設置 ➙ 選項 ➙ 模式設定 選擇家用或商店展示 。 若要在家使用,請選擇家用。 商店展示是用於店內陳設展示的模式。
❐❐返回初始設定 HOME ➾ 設置 ➙ 選項 ➙ 初始設定 刪除所有選擇性設定,並返回初始預設模式。 初始化完成後,電視會自行關閉再開啟。 ✎✎ 系統鎖定啟動之後,會出現快顯密碼提示。 ✎✎ 初始化過程中,切勿關閉電源。
❐❐使用 Home (首頁) 畫面 按下遙控器上的 HOME 按鈕。 藉助 Smart TV 的單一畫面集中功能設計,使用者可透過依主題 (直播電 視、記憶卡、我的應用程式) 排列的易用選單,輕鬆存取豐富的內容和應用 程式。 登入 特級 天氣 更多... 新聞 11-1 MBC HD 記憶卡編輯 SMART SHARE 劇院 更多... 體育 7 月 4 日下午 8:30 相片 地圖 Tron Toy story Monster Ghost Abata UP Thanks My Boy 搞笑 影片 我的卡 選擇所需的記憶卡。 遊戲 我的應用程式 輸入清單 設置 搜尋 網際網路 LG Smart...
❐❐使用和編輯我的卡 HOME ➾ 我的卡 為了讓您可以輕鬆查看並存取多種內容與功能,主要功能均已分門別類, 顯示在卡上。 透過選擇卡名,您就可以前往該類別頁面。 選擇首頁畫面頂端的編輯,切換卡的位置或建立您自己的卡。 (您無法編輯直播和付費卡。)
❐❐使用我的應用程式 HOME ➾ 我的應用程式 選擇首頁畫面底部的我的應用程式,或按下遙控器上的 MY APPS。 選擇我的應用程式以查看預先安裝的應用程式,以及您已下載的應用程 式。 我的應用程式 輸入清單 設置 搜尋 網際網路 LG Smart...
❐❐編輯我的應用程式中的項目: HOME ➾ 我的應用程式 ➙ 編輯 在我的應用程式頁面上,選擇畫面頂端的編輯以移動或刪除應用程式。 請 注意,您可以移動系統應用程式的位置,但無法將其刪除。 ✎✎ 在配備神奇遙控器的機型上拖曳應用程式圖示,藉此變更順序/刪除項 目。 我的應用程式 資源回收桶
❐❐管理 LG Smart TV 設定 HOME ➾ 設置 ➙ 選項 ➙ Smart TV 設定 設定許多 Smart TV 相關設定及管理 ID。 Smart TV 國家/ 地區 特級版本 ID 清單 在 Smart TV 上變更國家/地區設定。 接收您所選國家/地區的 Premium 服務與 LG Smart World。 顯示特級服務版本。 檢查和刪除登入至電視的 ID。 重新設定 從電視刪除所有已註冊的 ID 資訊。 法律聲明 顯示 Smart TV 的法律聲明。
必須要有無線或有線網路連線,才能使用各項 Smart 功能。 連線至網路時,您可以使用 Premium 內容、LG Smart World、DLNA 及其他 更多功能。 ❐❐按一下網路連線 輕鬆連線至有線/無線網路。 HOME ➾ 設置 ➙ 網路 ➙ 網路連線以自動連線至可用的網路。 遵循電視上 的提示操作。
❐❐透過進階設定連線至網路 HOME ➾ 設置 ➙ 網路 ➙ 網路連線 用於辦公室等特殊環境 (如果使用靜態 IP 的話)。 1 選擇有線或無線的網路連線。 2 透過 Wi-Fi 連線時,請使用下列其中一種網路連線方法。 接入點清單 連線至從接入點清單中選擇的網路。 輸入 SSID 連線至輸入的無線 AP。 WPS-PBC 按下支援 PBC 的無線 AP 按鈕時,即可輕鬆連線。
WPS-PIN Ad-hoc 在 AP 網站上輸入欲連線之無線 AP 的 PIN 碼時,即可 輕鬆連線。 透過具備無線功能的電腦或手機連線至網路。
❐❐使用 Wi-Fi Screen 功能 HOME ➾ 設置 ➙ 網路 ➙ Wi-Fi Screen Share 允許使用 Wi-Fi Direct 和 WiDi 等無線連線功能。 分享在 Smart Share 中透過 Wi-Fi Screen Share 連線之裝置的畫面。 1 將 Wi-Fi Screen Share 設成開。(若您不需要使用此功能,請將其變更為 關。) 2 啟用您要連線之裝置上的 [i-Fi Direct 設定。 3 隨即會顯示可連線到電視之裝置的清單。 4 選取要連線的裝置。 5 出現連線要求訊息時,選擇是。 6 若您要連線的裝置接受要求,Wi-Fi Screen Share 即會連線。
❐❐設定網路 - 警告 ✎✎ 使用標準 LAN 纜線 (含 RJ45 接頭的 Cat5 或更高規格,10 Base-T 或 100 Base TX LAN 連接埠)。 ✎✎ 重設數據機可能導致網路連線問題。 若要解決問題,請關閉電源、中斷 連接後再重新連接,然後重新開啟電源。 ✎✎ LG Electronics 對於網路連線所導致的任何網路連線問題或任何故障、功 能失常和錯誤等恕不負責。 ✎✎ 視網際網路服務供應商而定,網路連線可能無法正常運作。
✎✎ DSL 服務需要 DSL 數據機;有線服務則需要有線數據機。可以使用的網 路連線數量有限,而且視您與網際網路服務供應商 (ISP) 的合約而定,可 能無法使用電視網路設定。(如果每條線路只允許一台裝置,並且已連接 電腦,則無法使用其他裝置。) ✎✎ 無線網路可能會受到其他使用 2.
✎✎ 若要建立 AP 連線,必須具備支援無線連線的存取點裝置,並且必須在 裝置上啟用無線連線功能。請連絡服務供應商,瞭解存取點上的無線連 線是否可用。 ✎✎ 針對 AP 連線檢查 AP 的 SSID 和安全性設定。請參閱適當的文件,瞭解 AP 的 SSID 和安全性設定。 ✎✎ 若網路裝置 (有線/無線線路分享器、集線器) 上的設定無效,可能會導 致電視執行速度緩慢或無法正確操作。請根據適當的手冊正確安裝裝置 及設定網路。 ✎✎ 視已連線的裝置 (如筆記型電腦) 而定,Ad-hoc 連線可能無法運作。 ✎✎ 連線方法可能會依 AP 製造商而有所不同。
❐❐使用 Smart Share HOME ➾ Smart Share 藉由連接 USB 或連線家用網路 (DLNA、媒體連結),在電視上提供相片/音 樂/視訊檔案。 SMART SHARE 內容類型 更多... 最近觀看 更多... 新增 更多... 連結的裝置 全部 視訊 音樂 相片 錄影電視 設定 連線指南 更多...
❐❐控制電影播放 在觀賞電影時控制播放與設定選項。 選擇想要的播放點,然後播放。 停止播放及返回清單。 Option 播放 設定選項。 List 變更為 3D 模式。
❐❐控制相片檢視 以全螢幕檢視影像時控制播放和設定選項。 ✎✎ 對於 3D 圖像,即使幻燈片播放功能已啟用,幻燈片播放效果也不會發 生作用。 幻燈片播放 背景音樂 將相片顯示為 幻燈片播放。 播放背景音樂。 旋轉或放大影像。 選項 清單 停止播放及返回清單。 設定選項。 變更為 3D 模式。
❐❐控制音樂播放 在播放音樂時控制播放與設定選項。 選擇想要的播放點,然後播 放。 選項 播放 設定選項。 清單 返回清單
❐❐設定 Smart Share 相關功能 HOME ➾ Smart Share ➙ 設置 變更 Smart Share 內容播放的相關設定。 ❌❌進階設定 電視名稱 網路狀態 Wi-Fi Screen Share 共用我的電視 變更從其他裝置搜尋電視時所出現的名稱。 檢查網路連線。 允許使用 Wi-Fi Direct 和 WiDi 等無線連線功能。 允許/拒絕從其他裝置連線至電視。 開啟/關閉 DMR (數位媒體轉譯器) 連線。
接收時自動播 放 DivX VOD 接受/拒絕從其他裝置所傳送的內容。 註冊或取消註冊 DivX。 檢查 DivX 註冊碼以播放受 DivX 保護的視訊。 於 http:// vod.divx.com 註冊。 使用註冊碼在 www.divx.
❌❌歷史記錄 若要刪除內容歷史記錄,請按下方按鈕。 使用內容類型和連結的裝置功能 表的內容。 ❌❌隱私權 在新增的和最近觀賞的選單中,檢查您不希望開啟的裝置。
❐❐Smart Share 支援檔案 最大資料傳輸速率: 20 Mbps (每秒百萬位元) 支援的外部字幕格式: *.smi、*.srt、*.sub (MicroDVD、SubViewer 1.0/2.0)、 *.ass、*.ssa、*.txt (TMPlayer)、*.
❐❐視訊支援的轉碼器 最大節能: 1920 x 1080 @30p 副檔名 .asf .wmv .divx .avi .mp4 .m4v .mov 視訊 音效 視訊 音效 視訊 音效 轉碼器 VC-1 進階設定檔、VC-1 簡易設定及主要設定檔 WMA Standard、WMA 9 Professional DivX3.11、DivX4、DivX5、DivX6、XViD、H.264/AVC、 Motion Jpeg MPEG-1 Layer I、II、MPEG-1 Layer III (MP3)、 Dolby Digital、Dolby Digital Plus、LPCM、ADPCM、DTS H.
副檔名 .mkv .ts .trp .tp .vob .mpg .mpeg 視訊 音效 視訊 轉碼器 視訊 音效 H.264/AVC HE-AAC、Dolby Digital H.
❌❌可用的音樂檔案 檔案類 型 mp3 項目 位元速率 取樣頻率 支援 資訊 32 Kbps 至 320 Kbps 16 kHz 至 48 kHz MPEG1、MPEG2、Layer2、Layer3
❌❌可用的相片檔案 檔案類型 2D(jpeg, jpg, jpe) 3D(jps) 3D (mpo) 項目 可用的檔案 類型 相片大小 可用的檔案 類型 相片大小 設定檔 SOF0:標準 SOF1:延伸循序 SOF2:漸進式 最小:64 x 64 最大: 一般類型:15360 (寬) x 8640 (高) 漸進式類型:1920 (寬) x 1440 (高) mpo 4:3 尺寸: 3648 x 2736、2592 x 1944、2048 x 1536 3:2 尺寸:3648 x 2432
❐❐播放視訊的注意事項 ✎✎ 使用者建立的某些字幕可能無法正常運作。 ✎✎ 視訊及字幕檔案必須放在相同的資料夾中。 在此情況下,您必須為視訊 和字幕檔案指定相同的名稱,使其能夠正常顯示。 ✎✎ 我們不支援包含 GMC (全域移動補償) 或 Qpel (四分之一像素動作預測) 的 任何串流。 ✎✎ 僅支援 H.264/AVC 設定檔等級 4.
✎✎ 可能不會播放某些編碼器所建立的視訊檔案。 ✎✎ 可能不會播放非這裡所指定之格式的視訊檔案。 ✎✎ 可能無法正常播放儲存在 USB 裝置中不支援高速的視訊檔案。 ✎✎ USB 視訊檔案播放時,電視支援 DTS 音訊轉碼器。
DLNA 代表「數位生活網路聯盟」(Digital Living Network Alliance),能讓您透 過家用網路,在電視上觀賞電腦或伺服器上儲存的視訊 / 音樂 / 相片檔 案。 ❐❐連接經 DLNA 驗證的智慧型手機 電視和智慧型手機必須位於相同網路上。 1 2 3 4 5 6 7 確定智慧型手機上的 Wi-Fi 已啟用。 安裝 / 執行應用程式以分享智慧型手機上的內容。 執行 [分享我的手機內容]。 選擇您想要播放的內容種類 (視訊 / 音效 / 相片)。 選擇要在電視上播放的視訊、音樂或相片檔案。 選擇 [增加至播放清單]。 選擇您想在裝置上播放內容的電視機型名稱。 (電視機型名稱位於裝置的標籤上。) 8 Play ▶ 在電視上顯示選取的檔案。
❐❐連線 DLNA DMR (數位媒體轉譯器) 如果電腦的作業系統是 Windows 7,或您已透過網路連線 DLNA 認證的裝置 (例如行動電話),即可在電視上播放音樂 / 視訊 / 相片,而不需要安裝各別 程式。 1 在相同的網路上設定電視和電腦。 在網路上設定已安裝 Windows 7 的電 腦。 2 在您想要播放的音樂 / 視訊 / 相片檔案上按一下滑鼠右鍵,然後使用 Windows 7 隨附的 [遠端播放] 功能。 若要從裝置 (如行動電話) 播放內容,請參閱裝置的使用指南。 3 在電視的快顯視窗上選擇是。 即使連線了多台電視或裝置,也只會在一 個裝置上播放內容。 播放速度可能隨網路速度而異。
❐❐連線 DLNA DMP (數位媒體播放器) 利用具有 Nero MediaHome 4 Essentials 的 電腦,透過家用網路連結音樂 / 視訊 / 相片檔案後,即可在電視上重播這些檔案。 1 在相同的網路上設定電視和電腦。 必須透過單一存取點連線電視和每一 個裝置,才能啟用 DLNA 和媒體連結服務。 2 透過網站 (http://www.lg.
3 指出要透過電腦上安裝的 Nero MediaHome 4 Essentials 分享的檔案/資料 夾。 1. 執行電腦上安裝的 [Nero MediaHome 4 Essentials]。 2. 選擇要分享的資料夾項目。 3. 設定分享的資料夾,然後按一下 [啟動伺服器]。 伺服器就會啟動。 ✎✎ 如果電視上未出現分享的資料夾,請按一下 [本機資料夾] 索引標籤並重 新搜尋。 ✎✎ 如需詳細資訊和軟體相關資訊,請參閱網站 http://www.nero.
❌❌安裝 Nero MediaHome 4 Essentials 的電腦需求 • WindowsⓇ XP (Service Pack 2 或更新版本)、Windows VistaⓇ 、WindowsⓇ XP Media Centre Edition 2005 (Service Pack 2 或更新版本) 、Windows ServerⓇ 2003 (Service Pack 1 或更新版本) • WindowsⓇ 7 Home Premium、Professional、Enterprise 或 Ultimate (32 和 64 位元) • Windows Vista® 64 位元版本 (應用程式以 32 位元模式執行) • Windows® 7 64 位元版本 (應用程式以 32 位元模式執行) • 硬碟空間:超過 200 MB
• CPU:1.2 GHz IntelⓇ PentiumⓇ III 或 AMD Sempron™ 2200+ 處理器 • 記憶體:超過 256 MB RAM • 圖形卡:超過 32 MB,必須支援最低為 800 x 600 像素的解析度,以及至 少 16 位元的色彩設定 • WindowsⓇ Internet ExplorerⓇ 6.0 或更新版本 • DirectXⓇ 9.0c revision 30 (2006 年 8 月) 或更新版本 • 網路環境:100 MB 乙太網路、無線區域網路 WLAN (IEEE 802.
❌❌如果 DLNA 故障 ✎✎ 如果 DLNA 功能無法正常運作,請檢查網路設定。 ✎✎ 若要經由 DLNA 檢視 1080p 影像,您將需要 5 GHz 存取點;如果使用 2.
✎✎ DLNA 功能無法與不支援多點傳送的部分存取點搭配使用。 如需更多資 訊,請參閱存取點手冊或洽詢製造商。 ✎✎ 支援的檔案類型可能隨 DLNA 伺服器環境而異,即使是電視支援的檔案 類型也是如此。 ✎✎ 一個資料夾中若有過多子資料夾和檔案,可能會導致故障。 ✎✎ 對於來自 DLNA 伺服器的檔案,可能無法正確顯示其相關資訊。 ✎✎ 在 DLNA 伺服器上觀賞視訊字幕時,建議您使用 Nero MediaHome 4 Essentials。 ✎✎ 若稍後新增字幕檔案,請關閉分享的資料夾並且重新設定。 ✎✎ 無法播放位於 Nero MediaHome 伺服器上的 DRM 檔案。
❐❐連線至媒體連結 在連線至與 Smart TV 相同網路的個人電腦或筆記型電腦上安裝 Plex 程式, 以存取儲存在個人電腦 / 筆記型電腦上的各種多媒體,包括相片、視訊和 音樂。 1 在個人電腦 / 筆記型電腦上安裝 Plex Media Server 程式。 瀏覽網站 (http://www.lg.
❐❐使用媒體連結 HOME ➾ 媒體連結 媒體連結 可能會以英文提供資訊。 資料夾隨即會顯示為於 PLEX 媒 體管理員中設定的資料夾。 依伺服器排序 裝置選擇 PLEX 頻道 返回 離開
❐❐安裝 PLEX 的系統需求 • 最低需求 配備至少 1.6 GHz Intel Core Duo 處理器和 Windows XP SP3,最少 512 MB RAM 的電腦 • 建議使用於高畫質內容轉碼 (720p 和 1080p) 配備至少 2.4 GHz Intel Core Duo 處理器和 Windows XP SP3,最少 2 GB RAM 的電腦 支援 Windows XP、Vista 和 Windows 7 • 網路需求 適用於媒體中繼資料輸出和更新的 ADSL/纜線/Wi-Fi 網際網路連線 有線網路:配備 100 Base-T 或 1000 Base-T 的乙太網路 無線網路:建議使用 Uncongested 802.
❐❐使用媒體連結 - 警告 ✎✎ Mac 或 PC 電腦上安裝的 PLEX 媒體伺服器版本支援 0.9.1.
✎✎ 播放音樂影像剪輯時,不支援移動播放影像剪輯 (DLNA 亦同)。 ✎✎ 透過 Wi-Fi 連線播放高畫質視訊時,可能會發生延遲或不正常播放。 ✎✎ 如果 AP 設定不正確,電視可能無法辨識電腦。 (例如,若您在 AP 裝置上設定 [多點傳送轉發] 功能,電視則無法辨識 Wi-Fi 連線上的電腦。) ✎✎ 對於某些外掛程式,播放功能可能會受限於部分媒體類型。 ✎✎ 根據服務供應商的政策,外掛程式可能逕行變更且變得無法操作,恕不 事先通知。
❐❐連接 USB 裝置 將 USB 儲存裝置 (外部 HDD、USB 記憶體) 連接至電視的 USB 連接埠,在電 視上享受儲存於 USB 裝置中的內容檔案。 若要移除 USB 儲存裝置,請對您想要移除的裝置選擇快速選單 ➙ USB 裝 置;在看到 USB 已移除的訊息前,請勿移除實體裝置。 若強制卸除裝置, 電視或 USB 儲存裝置可能會發生錯誤。 ✎✎ 選取要移除的 USB 裝置之後,便無法再讀取此裝置。 移除 USB 儲存裝 置,然後再重新連接。
❐❐使用 USB 儲存裝置 - 警告 ✎✎ 若 USB 儲存裝置內建自動辨識程式,或使用其專屬的驅動程式,該裝置 可能無法運作。 ✎✎ 部分 USB 儲存裝置可能無法運作或無法正常運作。 ✎✎ 僅使用以 Windows FAT32 或 NTFS 檔案系統進行格式化的 USB 儲存裝 置。 ✎✎ 如為外部 USB HDD,建議您使用額定電壓 5 V 以下且額定電流值 500 mA 以下的裝置。 ✎✎ 建議在供電情況下使用 USB 集線器或硬碟機。 (如果供電不足,可能無法正確偵測到 USB 儲存裝置。)
✎✎ 建議您使用 32 GB 或容量更小的 USB 隨身碟,以及 2 TB 或容量更小的 USB HDD。 ✎✎ 若具有省電功能的 USB HDD 無法正常運作,請關閉電源再重新開啟電 源。 如需更多資訊,請參閱 USB HDD 的使用手冊。 ✎✎ USB 儲存裝置中的資料可能毀損,因此務必將重要檔案備份至其他裝 置。 維護資料是使用者的個人責任,因此對於任何資料遺失之情況,製 造商概不負責。
❐❐使用特級內容 HOME❐➾❐特級 連線至網路時,此服務可隨時提供豐富的內容,例如新聞、天氣、股票資 訊、重播電視節目及視訊。❐特級內容包含國家/地區特定的專門服務,會將 地區文化敏感性與全球內容納入考量。 特級 搜尋 廣播影像 登入 特級內容 選擇您要使用的內 容。 搞笑影片 劇院 天氣 相片 社交 網路 新聞 體育 視訊 地圖 遊戲 新增至我的應用程式 新增至我的應用 程式
❐❐使用付費內容 部分特級內容必須付費。 您可透過 LG Electronics 或相關內容提供者的專用付費 系統,為付費服務進行付費。 使用 LG 付費系統之前,您必須註冊會員資格並 登錄付款資訊,網址為 www.lgappstv.
4 完成購買程序後,請按一下購買按鈕以檢視您的購買內容。 5 在首頁畫面的上層選單中選擇您的 ID,然後從我的頁面 ➙ 付費查詢中查 看購買記錄。 您也可以在網站 (www.lgappstv.
✎✎ 為提高服務品質,服務供應商所提供的內容可能有所變更或刪減,恕不 事先通知。 請參閱相關內容提供者的網站,以瞭解關於內容的問題、疑 難排解或最新資訊。 LG Electronics 對於內容服務及相關資訊不負任何法 律責任,即使服務供應商中止服務亦然。 ✎✎ 特級服務的品質可能受網際網路連線影響。 如有任何網際網路速度的相 關問題或其他服務問題,請洽詢您的網際網路服務供應商。 ✎✎ 為取得最佳服務品質,建議您訂閱提供 4.0 Mbps 之速度 (1.
❐❐使用 LG Smart World HOME ➾ LG Smart World LG Smart World 是可透過 Smart TV 服務使用的電視應用程式服務。 您可下 載並享用各種熱門的付費/免費應用程式,包含教育、娛樂、生活與新聞。 我的應用程式 全部 遊戲 熱門 最佳付費 娛樂 最佳免費 生活 新項目 教育 總計 新聞/資訊 登入。 當您登入時,將會顯示 ID。 當您選擇 ID 時,可選擇我的頁面和登 出。 選擇要安裝的應用程式。
❐❐註冊 LG Smart World HOME ➾ 登入 必須註冊才能下載和執行應用程式。 1 選擇註冊並同意法律聲明。 2 輸入 ID 和密碼。 3 在 [確認密碼] 方塊中,再次輸入密碼。 4 選擇確認以完成註冊程序。 ✎✎ 如果您只有 TV 帳戶,則只能使用免費應用程式。 若要使用付費應用程 式,請將您的付款方法新增至我們的網站 (www.lgappstv.
❐❐在電視上安裝應用程式 HOME ➾ LG Smart World 1 首先請登入。 2 從清單中選擇所需的應用程式。 使用搜尋功能快速尋找所需的應用程 式。 3 選擇 [詳細資訊] 中的 [安裝],在電視上安裝應用程式。 您需要支付付費 應用程式的費用。
✎✎ 您可以透過電腦或電視購買應用程式,但必須使用電視來安裝與執行這 些應用程式。 ✎✎ 如果電視的儲存空間不足,您可以針對 USB 應用程式,將應用程式下載 到透過電視端子所連接的 USB 儲存裝置。 您可從我的應用程式畫面, 執行 / 刪除 / 移動儲存在 USB 上的應用程式。 ✎✎ 內含應用程式的 USB 儲存裝置不可用於儲存其他資料。 (僅適用於 USB 應用程式)
❐❐管理我的資訊 HOME ➾ LG Smart World 1 2 3 4 登入。 在畫面頂端上選擇目前登入的 ID。 選擇我的頁面。 藉由檢查 [會員資訊]、[我的已購買應用程式清單] 和 [電視已安裝的應用 程式清單] 來進行管理。
我的資訊 顯示目前登入的 ID 基本資訊。 若要變更您的會員 資訊,請在電腦上瀏覽 www.lgappstv.
HOME ➾ 網際網路 在電視上手動輸入 URL,或瀏覽新增至 [喜愛頻道] 的網站。 輸入網址。 開啟數個網頁瀏覽 器時選擇。 將目前網頁加至我的最愛。 移至瀏覽過的網站。
✎✎ 網際網路支援最高 Flash 10,但不支援平台相依技術,如 ActiveX。 ✎✎ 網際網路僅適用於預先安裝的外掛程式。 ✎✎ 網際網路可能無法播放下列檔案格式以外的任何檔案格式: JPEG / PNG / GIF / WMV (ASF) / WMA / MP3 / MP4 ✎✎ 網際網路在記憶體不足時將會強制關閉。 ✎✎ 對於網際網路,系統會採用安裝在電視上的字型,且視播放的內容而 定,字型可能無法正常顯示。 ✎✎ 網際網路不支援檔案及字型下載。 ✎✎ 網際網路是針對電視設計,因此可能與專為電腦而設計的瀏覽器具備不 同功能。 ✎✎ 網際網路是電視瀏覽器,播放某些內容檔案時可能無法正常運作。
HOME ➾ Social Center LG Smart TV Social Center 應用程式讓您在觀賞電視時可享用 Facebook 或 Twitter 等 SNS 服務。 利用 Social Center 應用程式,您可與朋友進行通訊,並查看 SNS 連絡人發 佈的訊息與相片,全部一次完成。 1 登入您的 LG TV 帳戶,如果不是會員,請先註冊。 2 登入所需的服務 (Facebook 或 Twitter), 如果不是會員,請先建立帳戶。 3 在觀賞電視時查看 SNS 服務和發佈訊息。 從 Social Center 應用程式在 Facebook 或 Twitter 上發佈的訊息,也會出 現在網頁或行動網頁上。
SOCIAL CENTER 切換 Facebook/Twitter。 Refresh
✎✎ 如果我的應用程式上沒有 Social Center 應用程式,請從 LG Smart World 安裝應用程式。 ✎✎ 使用 LG 神奇遙控應用程式在您的智慧型手機上登入 SNS 服務,讓輸入 文字訊息時更加方便。 該應用程式可在 Google Play Store 或 Apple App Store 取得。
需要註冊才能使用 LG Smart World。 使用免費應用程式的會員資格:在電視或電腦上註冊。 購買付費應用程式的會員資格:僅在電腦上註冊。 問題 進入選單時,一律會出 現 [正在初始化] 訊息。 特級功能卡上未顯示內 容。 解決方法 • 正在初始化 訊息會在重新啟動微處理器與硬體、設定 網路通訊,以及建立 SDP 通訊 (裝置驗證與基本資訊 下載) 時出現。 大約需花費 20 秒,而且這是一般的程 序。 • 如果您變更 Smart TV 上的國家/地區設定,則內容可能 無法顯示。 在 HOME ➾ 設置 ➙ 選項 ➙ Smart TV 設定 ➙ Smart TV 國家/地區中變更國家/地區。
問題 使用網際網路功能時, 有些網站會包含空格。 網際網路會於瀏覽網站 時自動關閉。 我已在電視上註冊。 我是否還需要在網站 (www.lgappstv.com) 上 註冊? 解決方法 • 電視的網際網路最高可支援 Flash 10,並僅能以下列格 式播放檔案: JPEG、PNG、GIF、WMV (ASF)、WMA、MP3、MP4 • 如果因網頁資訊量而導致記憶體不足,系統可能會強 制關閉網際網路。 • 您可以使用在電視上註冊的 ID 和密碼來登入網站 (www.lgappstv.com)。 使用在電視上註冊的 ID 和密碼 登入後,請輸入您的個人資訊。 一旦完成電子郵件驗證程序,即完成網站 (www. lgappstv.
問題 解決方法 每位家庭成員是否可在 單一電視上使用不同的 ID? • 您可在一台電視上註冊並使用多個 ID。 • 您可在 HOME ➾ 設置 ➙ 選項 ➙ Smart TV 設定 ➙ ID 清 單中,檢視在電腦上註冊的 ID。 • 您可以檢查每一個 ID 所購買的應用程式清單。 不過, 您可能會在我的應用程式中看到每一個 ID 安裝的所有 應用程式。 如果我忘記 ID 了,該怎 麼辦? • 若您是透過電腦註冊,請使用網站 (www.lgappstv.
問題 解決方法 我從網站 (www.lgappstv. • 如果您想查看在電視上購買的應用程式,請登入網站 並在 [已購買的應用程式] 選單上檢視內容。 com) 購買了應用程式。 該如何在電視上使用應 在首頁頂端選擇 ID,並在我的頁面 ➙ 已購買的應用程 用程式? 式中檢查該應用程式。 我是否能查看已購買應 用程式的歷史記錄? • 在首頁頂端選擇 ID,並在我的頁面 ➙ 已購買的應用程 式中檢查該應用程式。 • 登入網站 (www.lgappstv.
問題 解決方法 • 檢查電視型號是否支援 LG Smart World。 我是否能在電視和電腦 • LG Smart TV 的 LG Smart World 所提供的應用程式只能 在 LG Smart TV 上執行。 上,使用 LG Smart TV 的 • 您亦可從網站 (www.lgappstv.
問題 畫面上顯示的應用程式 大小,不同於在電視上 安裝的實際應用程式大 小。 我忘記電視密碼了。 該 怎麼辦? 解決方法 • 畫面上顯示的應用程式大小包含安裝應用程式所需的額 外空間,因此可能與實際安裝的應用程式大小不同。 • 如果您只有 TV 帳戶,密碼若遺失即無法復原。 建立新 ID 並用此 ID 登入。 • 如果您在電視和電腦上皆有註冊,則可使用本公司網 站 (www.lgappstv.
問題 解決方法 我是否需要在網站上儲 存付費資訊,以 購買付費應用程式? • 若要從您的電視購買付費應用程式,您必須在網站 (www.lgappstv.
問題 我已註冊成為會員,但 無法購買付費應用程 式。 解決方法 • 用您在電腦上建立的 ID 登入,並新增您的付款資訊。 接著從電視登出後再次登入,這樣即可購買付費應用 程式。
❐❐檢視 3D 影像 3D 影像是利用左右眼視差的技術,可讓電視上的影像看起來如同真實的三 維空間。 1 播放 3D 影片或轉到 3D 節目。 2 戴上 3D 眼鏡。 3 按下 3D 按鈕以變更為 3D 影像。 4 若要結束 3D 影像觀賞,請於觀賞 3D 影像時按下遙控器上的 3D 按鈕。 ✎✎ 可用的 3D 類型因輸入訊源而異。
❐❐調整 3D 影像細節 HOME ➾ 設置 ➙ 影像 ➙ 3D 設定 調整 3D 影像的各方面設定。 3D 模式 提供適當的 3D 深度。 • 3D 深度:調整物件與背景間的 3D 深度。 • 3D 視點:可以從使用者的位置調近或調遠 3D 影 像。
3D 聲音調變 3D 模式識別 一般影像檢視 3D 色彩校正 3D 畫面糾正 提供 3D 最佳化音效。 藉由分析原始畫面的模式,自動轉換為 3D。 您可以檢視移除 3D 效果的 2D 影像。 校正 3D 影像的色彩。 ✎✎ 視型號而定,可能無法使用 3D 色彩校正功能。 切換 3D 視訊的左/右影像。
❐❐觀賞 3D 影像 - 警告 ✎✎ 觀賞 3D 影像時,建議觀賞者與螢幕保持至少螢幕對角長度兩倍的距 離。 ✎✎ 使用須充電的快門式眼鏡可能無法正確地觀看 3D 影像。 ✎✎ 如果未來這部電視不支援的 3D 廣播格式變成標準格式,您可能需要額 外使用機上盒之類的裝置。
❐❐使用 3D 眼鏡 - 警告 ✎✎ 請勿使用 3D 眼鏡來代替您自己的矯正眼鏡、太陽眼鏡或護目鏡。 錯誤 使用 3D 眼鏡可能會造成眼睛受傷。 ✎✎ 請勿將 3D 眼鏡存放於極端的環境條件下。 暴露在極高或極低的溫度下 可能會使鏡片變形。 請勿配戴變形的眼鏡。 ✎✎ 請勿重壓或撞擊 3D 眼鏡。 使用 3D 眼鏡時太過粗魯可能會使其受損。 ✎✎ 3D 眼鏡的鏡片 (含偏光膜) 很容易刮傷。 請只使用乾淨的軟布清潔鏡 片。 髒布可能會刮傷偏光膜。 ✎✎ 請勿使用尖銳物體刮傷 3D 眼鏡的鏡片表面,或用化學製品清潔鏡面。 如果鏡片表面刮傷,可能無法正確地顯示 3D 影像。
❐❐連接專屬的 DVR USB 儲存裝置 1 將 USB HDD (40 GB 或更大) 連接到電視上的 Time Machine Ready 插孔。 DVR 功能僅能搭配 Time Machine Ready 插孔運作。 2 USB HDD 必須經過初始化才能用於 DVR。連接尚未初始化的 USB HDD 時,請選擇 MY APPS ➾ TIME MACHINE。USB 裝置初始化畫面隨即出 現。 3 完成 USB HDD 初始化,然後將 時間平移模式設為開。 ✎✎ 若要移除 USB 儲存裝置,請選擇快速選單 ➙ USB 裝置,並且確認表示 USB 儲存裝置已移除的訊息,然後再卸除實體裝置。
❐❐變更時間平移模式或初始化 USB 儲存裝置 滾輪(OK) ➾ 選項 使用 DVR 時變更 DVR 設定。 時間平移模式 USB 裝置初始化 開:電視開啟時,自動啟用時間平移模式。 關:停用時間平移模式。 連接的 HDD 會變成可搭配 DVR 一起使用。 儲存在 USB 裝置上的所有資料都會被刪除。
✎✎ 建議您使用 HDD (硬碟)。 SSD (固態硬碟) 的寫入/清除次數有限。 ✎✎ 建議使用 40 GB 或小於 2 TB 的 USD HDD。 ✎✎ 無法在電腦上辨識任何要使用的 USB 裝置初始化。 ✎✎ 儲存在 USB 裝置上的資料可能已損壞。 維護資料是使用者的個人責任, 因此對於任何資料遺失之情況,製造商概不負責。 ✎✎ 如果 USB 儲存裝置上的資料磁區有問題,則裝置可能無法正常運作。
Time Machine 可讓您在觀看數位播出時,將直播電視節目儲存在 USB 儲存 裝置中,以便稍後觀看錯過的節目片段,以及觀賞先前播出的節目。 ✎✎ 時間平移模式最高可設為 90 分鐘。 (針對義大利,該模式最高可設為 60 分鐘。) ✎✎ 如果 USB 儲存裝置的資料磁區發生錯誤,可能會導致故障。
Time Machine 使用期間按下滾輪(OK)。 選擇想要的播放點,然後播放 變更時間平移模式 初始化 USB 裝置 移到目前廣播播放時間 錄影開始 直播電視 從目前的播放點開 始錄影 電視錄影 DVR 播放控制 預約清單 節目表 查看定義的預 約清單 顯示錄影的節目 設定預約 ✎ 顯示的圖片可能與您的電視不同。 選項
❐❐立即開始錄影 滾輪(OK) ➾ 錄影開始 如果您在觀看節目時需要暫時離開,可以錄下節目。 ✎✎ 僅會錄下您目前正在觀看的數位廣播節目。 ✎✎ 如果您在錄影時強制關閉電視電源,節目可能不會儲存。 適當做法是停 止錄影,檢查節目是否錄製成功,然後再關閉電源。 ✎✎ 節目受相關著作權法保護,因此複製及播放節目之前,須事先取得著作 權擁有者的許可。 使用本裝置錄影的內容僅供私人使用。 禁止將受著 作權保護的錄影內容販售、傳輸或出借給第三方。
❌❌停止錄影 滾輪(OK) ➾ 錄影停止 立即停止錄影。 ❌❌修改錄影停止時間 滾輪(OK) ➾ 停止選項 ➙ 錄影停止時間修改 ✎✎ 最長錄影時間為 5 小時。
❐❐預約錄影 滾輪(OK) ➾ 節目表 按節目選擇計劃 表 按日期選擇計劃 表 從 [節目導覽] 畫面選擇要觀看或錄影的節目。 選擇要觀看或錄影的日期、時間和節目。 ✎✎ 定時錄影的最短時間為 2 分鐘。 ✎✎ 受損的磁碟磁區可能會影響預約清單上的部分或所有項目。 ✎✎ 預約清單中的項目數量上限為 30 個。
❐❐確認及/或修改預約清單 滾輪(OK) ➾ 預約清單 確認、修改或刪除預約的觀賞或錄影節目。
❐❐觀觀看電視錄影 HOME ➾ SmartShare ➙ 電視錄影 選擇儲存在 USB HDD 中的錄影節目以檢視/刪除該節目。 從上次停止處接 續播放 重頭播放 刪除 針對先前曾播放過的錄影節目,從上次停止處接續播 放。 從一開始播放選取的錄影節目。 刪除選取的錄影節目。 ✎✎ 電視錄影的數量上限為 300。
❐❐控制錄影播放 播放時,按下遙控器上的❐滾輪(OK)❐按鈕。 選擇想要的播放點,然後播放。 縮圖清單 播放控制 縮圖清單 影片編輯片段 設定錄影播放選項 重複 影片編輯片段/ 重複播放功能 ✎ 顯示的圖片可能與您的電視不同。 選項 3D❐檢視 節目清單
從 Google Play Store 或 Apple App Store 下載 LG 動感遙控應用程式,以便使 用您的智慧型手機觀看電視。 • 現在您可以在智慧型手機上享受您喜愛的電視節目。 (僅限某些型號) • 在智慧型手機上新增喜愛的頻道。 • 您可以直接在智慧型手機上使用特級、我的應用程式之類的功能。 • 從智慧型手機中,使用電視搜尋功能選擇一個項目,在電視上觀看該項 目。 • 支援文字輸入功能,讓您可以輕鬆輸入文字。 (在某些畫面上無法輸入 文字。) • 選擇應用程式的觸控板,依動感遙控器指標運作的相同方式來進行控 制。 ✎✎ 支援的功能可能隨電視或 LG 動感遙控應用程式的版本而異。
❐❐使用 USB 有線/無線滑鼠 將滑鼠連接至 USB 連接埠。 在電視畫面上使用滑鼠來移動指標,然後選擇 所要的選單。 滑鼠的右鍵及特殊按鈕無法運作。 滑鼠 神奇遙控器 左鍵 動感遙控器上的 OK 按鈕 滾輪按鈕 動感遙控器上的滾輪按鈕 ✎✎ 無線 USB 滑鼠與鍵盤的使用狀況可能會受無線電頻率環境和距離的影 響。
❐❐使用 USB 有線/無線鍵盤 將鍵盤連接至 USB 連接埠。 使用搜尋功能和網際網路時,您可以使用鍵盤 輸入文字。 ✎✎ 在某些畫面上無法輸入文字。 ✎✎ 適用的鍵盤 建議您使用通過 LG TV 相容性測試的產品。 LOGITECH K200、LOGITECH K400、MICROSOFT Comfort Curve 2000 、MICROSOFT MS800 和 LG Electronics ST-800
❐❐使用遊戲控制器 如果遊戲支援使用遊戲控制器,請將遊戲控制器連接至 USB 連接埠。 ✎✎ 適用的遊戲控制器 建議您使用通過 LG TV 相容性測試的授權遊戲控制器。 Logitech F310、Logitech F510 和 Logitech F710
HOME ➾ 設置 ➙ 支援 ➙ 軟體升級 使用軟體升級以檢查和取得最新版本。 您也可以手動檢查可用的更新。 軟體升級 檢查更新版本 將其設定為開。 偵測到更新檔案時,系統會自動下載檔案。 檔案下載完成時,即會顯示軟體升級視窗。 檢查已安裝的最新更新版本。 有新的更新可用時,可 以手動執行下載程序。
✎✎ 最新版本可透過數位廣播訊號或網際網路連線取得。 ✎✎ 在透過數位廣播訊號下載軟體時切換節目會中斷下載程序。 回到最初的 節目可讓下載繼續。 ✎✎ 如果未更新軟體,某些功能可能無法正常運作。 ✎✎ [僅限北歐型號] 您可藉由以下方法,檢查在 DTV 頻道中是否可以使用 LG OTA 服務:當 您在頻道橫幅下看到找到更新!訊息時,按下紅色按鈕。
若發生下列情況,請依照下方所述方式,進行檢查和調整。 發生的情況可 能不是故障導致。 HOME ➾ 設置 ➙ 支援 ➙ 訊號測試 顯示 MUX 和服務等資訊。若您選擇 [天線和衛星] 或 [線纜和衛星],則僅會 顯示天線或纜線的訊號測試。 ❐❐一般 問題 解決方法 無法觀看某些頻道。 • 調整天線位置或方向。 • 將所需的頻道儲存在自動頻道記憶或頻道編輯。 開啟電視電源之後, 會經過一段延遲時間, 才能出現完整影像。 • 此程序是為了清除電視開啟時可能出現的影像雜訊, 所以這是正常現象。
❐❐影像 HOME ➾ 設置 ➙ 支援 ➙ 影像測試 開啟 [影像測試],檢查影像訊號輸出是否正常。 若測試影像沒有問題,請檢查外部裝置連接狀況或廣播訊號。 問題 來自上一個頻道或其他頻 道的影像可能殘留在畫面 上,或畫面上出現干擾線 條。 解決方法 • 嘗試調整天線使其朝向電視台的方向,或參閱手冊 以瞭解連接天線的正確方式。
問題 解決方法 短暫出現震動的水平/垂直 線條和魚網狀圖案。 • 有強力電子干擾時,可能會發生這類問題。 關閉其 他電子裝置,例如手機、電動工具和其他小家電。 • 訊號微弱或收訊不穩定時,可能會發生此問題。 調 整天線方向或纜線連接方式。 • 若手動頻道調整的訊號強度或品質過低,請致電給 電視台或管理辦公室要求檢查。 觀看數位廣播時,畫面顯 示器停格或無法正常運 作。 即使已接上纜線,仍無法 開啟數位廣播。 • 請洽訂閱和/或訊號相關的有線電視服務業者 (視訂 閱內容而定,數位廣播可能不受支援)。
問題 解決方法 • 檢查 HDMIⓇ 纜線規格。 僅限使用 HDMIⓇ 纜線。 其 他的纜線可能會導致影像忽明忽暗,或無法正常顯 連接至 HDMI 時,影像未顯 示。 示或不清晰。 • 確認所有纜線均穩固連接。 連接不牢固時,可能無 法正常顯示影像。 連接 USB 儲存裝置時無法 運作。 • 確認 USB 裝置和纜線是否為 2.
❐❐音效 HOME ➾ 設置 ➙ 支援 ➙ 聲音測試 首先嘗試聲音測試,以確認音效訊號輸出正常。 若測試音效正常,請檢查外部裝置連接狀況或廣播訊號。 問題 解決方法 畫面顯示器已開啟,但沒有 • 檢查其他電視頻道是否也有此問題。 聲音。 • 確定電視揚聲器設成開。 觀看類比廣播時,立體音不 清晰,或只有一個揚聲器有 聲音。 • 當處於收訊不佳的區域 (訊號微弱或不穩定的區域) 中,或多重音效不穩定時,請在多重音效上選擇單 音。 • 使用導覽按鈕調整平衡。
問題 解決方法 電視音效與影像上的嘴型不 • 若此問題只發生在特定電視頻道,則可能是該電視 台的廣播訊號發生問題所導致。 請洽該電視台或當 同步,或音效不時斷斷續 地的有線電視服務業者。 續。 每當變更頻道時,音量大小 • 音量大小會因頻道不同而有所差異。 都不同。 • 請將自動音量平衡設成開。
問題 解決方法 某些頻道不會出現音效,或 只會播放背景音樂 (當節目 • 在 [語言] 中,將語言 ➙ 音效語言設為所需的語 言。 即使已變更多重音效的語言,一旦關閉電源或 是專門針對海外觀眾所製作 變更頻道,便會重新設定預設值。 時,便可能出現這種情況) 。 連接至 HDMI/USB 時,沒有 聲音。 • 確定 HDMIⓇ 纜線為高速纜線。 • 檢查 USB 裝置和纜線是否為 2.
❐❐電腦連線問題 問題 連接至電腦之後,無法 開啟螢幕畫面。 使用 HDMI 纜線連接電 腦後,沒有聲音。 解決方法 • • • • • 確認電腦和電視之間已穩固連接。 用遙控器關閉電視電源,然後再開啟電源。 電視電源開啟時,重新啟動電腦。 檢查解析度是否正確設定為適合 PC 輸入的設定。 若要使用電視當作第二台顯示器,請檢查所連接的桌上 型或筆記型電腦是否支援雙顯示器顯示功能。 • 重新連接 RGB/HDMI 纜線。 • 請洽顯示卡的製造商,確認該顯示卡是否支援 HDMI 語 音輸出 (若使用 DVI 格式的顯示卡,則需連接獨立的音 效纜線)。
問題 解決方法 連接至電腦時,顯示畫 面部分遭到截斷,或往 某一側偏移。 • 設定支援 PC 輸入的解析度 (若這個方法沒有用,請將電 腦重新開機)。 • 選擇畫面 (RGB-PC),然後調整位置/大小/相位。
❐❐無法使用 [我的媒體] 重播電影。 問題 解決方法 無法顯示 [電影清單] 中的 • 檢查電腦是否能夠讀取 USB 儲存裝置中的檔案。 檔案。 • 檢查是否為支援的副檔名。 • 確認電腦的視訊播放器是否能正常重播檔案 (檢查檔 案是否毀損)。 出現「此檔案無效」錯誤訊 息;或可以聽見聲音,但 • 檢查電腦是否支援所設定的解析度。 • 確認視訊/音效轉碼器是否受支援。 無法正常顯示影像。 • 確認畫面播放速率是否受支援。
問題 出現「不支援的音效格 式。」錯誤訊息;或可以 正常顯示影像,但無法聽 見聲音。 解決方法 • 確認電腦的視訊播放器是否能正常重播檔案 (檢查檔 案是否毀損)。 • 確定電腦是否支援音效轉碼器。 • 確認位元率是否受支援。 • 確認取樣速率是否受支援。
問題 未顯示字幕。 解決方法 • 確認電腦的視訊播放器是否能正常重播檔案 (檢查檔 案是否毀損)。 • 檢查視訊檔案是否與字幕檔案共用相同名稱。 • 確認視訊檔案和字幕檔案是否放在同一個資料夾。 • 確認字幕檔案格式是否受支援。 • 確認字幕語言是否受支援 (開啟 [記事本] 中的字幕檔 案以查看語言)。 ✎✎ 顯示的圖片可能與您的電視不同。 ✎✎ 如需要求服務的相關資訊,請參閱電視選單。 HOME ➾ 設置 ➙ 支援 ➙ 產品/服務資訊
若發生下列情況,請依照下方所述方式,進行檢查和調整。 發生的情況可 能不是故障導致。 HOME ➾ 設置 ➙ 支援 ➙ 訊號測試 顯示 MUX 和服務等資訊。若您選擇 [天線和衛星] 或 [線纜和衛星],則僅會 顯示天線或纜線的訊號測試。 ❐❐一般 問題 解決方法 無法觀看某些頻道。 • 調整天線位置或方向。 • 將所需的頻道儲存在自動頻道記憶或頻道編輯。 開啟電視電源之後, 會經過一段延遲時間, 才能出現完整影像。 • 此程序是為了清除電視開啟時可能出現的影像雜訊, 所以這是正常現象。
❐❐影像 HOME ➾ 設置 ➙ 支援 ➙ 影像測試 開啟 [影像測試],檢查影像訊號輸出是否正常。 若測試影像沒有問題,請檢查外部裝置連接狀況或廣播訊號。 問題 來自上一個頻道或其他頻 道的影像可能殘留在畫面 上,或畫面上出現干擾線 條。 解決方法 • 嘗試調整天線使其朝向電視台的方向,或參閱手冊 以瞭解連接天線的正確方式。
問題 解決方法 短暫出現震動的水平/垂直 線條和魚網狀圖案。 • 有強力電子干擾時,可能會發生這類問題。 關閉其 他電子裝置,例如手機、電動工具和其他小家電。 • 訊號微弱或收訊不穩定時,可能會發生此問題。 調 整天線方向或纜線連接方式。 • 若手動頻道調整的訊號強度或品質過低,請致電給 電視台或管理辦公室要求檢查。 觀看數位廣播時,畫面顯 示器停格或無法正常運 作。 即使已接上纜線,仍無法 開啟數位廣播。 • 請洽訂閱和/或訊號相關的有線電視服務業者 (視訂 閱內容而定,數位廣播可能不受支援)。
問題 解決方法 • 檢查 HDMIⓇ 纜線規格。 僅限使用 HDMIⓇ 纜線。 其 他的纜線可能會導致影像忽明忽暗,或無法正常顯 連接至 HDMI 時,影像未顯 示。 示或不清晰。 • 確認所有纜線均穩固連接。 連接不牢固時,可能無 法正常顯示影像。 連接 USB 儲存裝置時無法 運作。 • 確認 USB 裝置和纜線是否為 2.
❐❐音效 HOME ➾ 設置 ➙ 支援 ➙ 聲音測試 首先嘗試聲音測試,以確認音效訊號輸出正常。 若測試音效正常,請檢查外部裝置連接狀況或廣播訊號。 問題 解決方法 畫面顯示器已開啟,但沒有 • 檢查其他電視頻道是否也有此問題。 聲音。 • 確定電視揚聲器設成開。 觀看類比廣播時,立體音不 清晰,或只有一個揚聲器有 聲音。 • 當處於收訊不佳的區域 (訊號微弱或不穩定的區域) 中,或多重音效不穩定時,請在多重音效上選擇單 音。 • 使用導覽按鈕調整平衡。
問題 解決方法 電視音效與影像上的嘴型不 • 若此問題只發生在特定電視頻道,則可能是該電視 台的廣播訊號發生問題所導致。 請洽該電視台或當 同步,或音效不時斷斷續 地的有線電視服務業者。 續。 每當變更頻道時,音量大小 • 音量大小會因頻道不同而有所差異。 都不同。 • 請將自動音量平衡設成開。
問題 解決方法 某些頻道不會出現音效,或 只會播放背景音樂 (當節目 • 在 [語言] 中,將語言 ➙ 音效語言設為所需的語 言。 即使已變更多重音效的語言,一旦關閉電源或 是專門針對海外觀眾所製作 變更頻道,便會重新設定預設值。 時,便可能出現這種情況) 。 連接至 HDMI/USB 時,沒有 聲音。 • 確定 HDMIⓇ 纜線為高速纜線。 • 檢查 USB 裝置和纜線是否為 2.
❐❐電腦連線問題 問題 連接至電腦之後,無法 開啟螢幕畫面。 使用 HDMI 纜線連接電 腦後,沒有聲音。 解決方法 • • • • • 確認電腦和電視之間已穩固連接。 用遙控器關閉電視電源,然後再開啟電源。 電視電源開啟時,重新啟動電腦。 檢查解析度是否正確設定為適合 PC 輸入的設定。 若要使用電視當作第二台顯示器,請檢查所連接的桌上 型或筆記型電腦是否支援雙顯示器顯示功能。 • 重新連接 HDMI 纜線。 • 請洽顯示卡的製造商,確認該顯示卡是否支援 HDMI 語 音輸出 (若使用 DVI 格式的顯示卡,則需連接獨立的音 效纜線)。
問題 解決方法 連接至電腦時,顯示畫 面部分遭到截斷,或往 某一側偏移。 • 設定支援 PC 輸入的解析度 (若這個方法沒有用,請將電 腦重新開機)。
❐❐無法使用 [我的媒體] 重播電影。 問題 解決方法 無法顯示 [電影清單] 中的 • 檢查電腦是否能夠讀取 USB 儲存裝置中的檔案。 檔案。 • 檢查是否為支援的副檔名。 • 確認電腦的視訊播放器是否能正常重播檔案 (檢查檔 案是否毀損)。 出現「此檔案無效」錯誤訊 息;或可以聽見聲音,但 • 檢查電腦是否支援所設定的解析度。 • 確認視訊/音效轉碼器是否受支援。 無法正常顯示影像。 • 確認畫面播放速率是否受支援。
問題 出現「不支援的音效格 式。」錯誤訊息;或可以 正常顯示影像,但無法聽 見聲音。 解決方法 • 確認電腦的視訊播放器是否能正常重播檔案 (檢查檔 案是否毀損)。 • 確定電腦是否支援音效轉碼器。 • 確認位元率是否受支援。 • 確認取樣速率是否受支援。
問題 未顯示字幕。 解決方法 • 確認電腦的視訊播放器是否能正常重播檔案 (檢查檔 案是否毀損)。 • 檢查視訊檔案是否與字幕檔案共用相同名稱。 • 確認視訊檔案和字幕檔案是否放在同一個資料夾。 • 確認字幕檔案格式是否受支援。 • 確認字幕語言是否受支援 (開啟 [記事本] 中的字幕檔 案以查看語言)。 ✎✎ 顯示的圖片可能與您的電視不同。 ✎✎ 如需要求服務的相關資訊,請參閱電視選單。 HOME ➾ 設置 ➙ 支援 ➙ 產品/服務資訊
❐❐根據NCC低功率電波輻射性電機管理辦法 規定 第十二條 第十四條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或 使用者均不得擅自變更頻率、加大功率或變更原設計之特性及 功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經 發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續 使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻 射性電機設備之干擾。