Easy Setup Guide LG Digital Signage (MONITOR SIGNAGE) Please read this manual carefully before operating your set and retain it for future reference. 55LV75A 55LV77A *MFL68606109* www.lg.
ASSEMBLING AND PREPARING ENGLISH ENG ASSEMBLING AND PREPARING Accessories Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
ASSEMBLING AND PREPARING 3 Dimensions (Width x Height x Depth) / Weight ENG ENGLISH H W D 1213.4 mm x 684.2 mm x 88.5 mm / 23 kg (47.7 inches x 26.9 inches x 3.4 inches / 50.7 lbs) To View the Owner’s Manual Insert CD-ROM in Computer. CD-ROM will open automatically.(for Windows only) If it does not run automatically, it is available to see the below sequence. My computer ➙ Digital_LG(CD-ROM) ➙ Index.
ASSEMBLING AND PREPARING PRECAUTION IN MOVEMENT ENGLISH ENG - The illustration may look different from the actual product. Adhere to the warning signs printed on the Box. Do not tumble the Set box sideward down. Do not Clamp Do not drop from clamping. 2 Persons needed for transport Load with care. Do not place the product on the top of a box. Do not drop from stacking. 4 Persons needed for transport Do not transport horizontally. Do not drop from carrying. Do not lean on the product.
ASSEMBLING AND PREPARING 5 Precaution Move the Set as a team of 2 persons. When you move the bare Set, please use one hand on grabbing the handle and the other support under the Set. 1 Remove the L-bracket on the corner of the Set before installation. When moving the Set, re-assemble the L-bracket. 2 Be careful not to collide the sets with the floor or with each other. Install in the space with enough airflow.
ASSEMBLING AND PREPARING ENGLISH ENG Causes & Phenomena of the Line Defect COF (CHIP ON FILM) DEFECT The line defect would occur on your Set if you strike on the edge of the Set.
ASSEMBLING AND PREPARING 7 Installing the Product 1 Cut Packing Strap of the Box. 2 Cut Tape on the Box. 3 Open the Box and remove the top packing. 4 Remove the Upper Box. 5 Open the Poly Bag. 6 Undress the Poly Bag. ENG ENGLISH - The illustration may look different from the actual product.
ASSEMBLING AND PREPARING 7 Lift up the Set using the SIDE/BACK Handle. 8 9 With one hand under the set and the other hand grabbing the set, move the set. Remove Bottom packing when lifting up the Set. ENGLISH ENG 10 Lay the back of the Set down on the table.
ASSEMBLING AND PREPARING 9 11 Use the cushion or Pad when you lay the face of the Set downward. ENG ENGLISH 12 Connect IR receiver to use remocon. And then, connect power cord.
ASSEMBLING AND PREPARING How to Join Sets How to Mount the Set 1 Join other sets using screws for fixing the VESA wall mount in the same way as above. Example of 2 x 2 tiling Screws for attaching the VESA wall mount (M6) Screws (15-M4) ≤ 6 mm Set 4 joined to the rest of the sets (2 x 2 tiling) 2 After joining the sets, use the tiling guide to adjust the gap between the sets. 600 400 ENGLISH ENG Tiling Displays 3 Now the 2 x 2 tiling is complete.
REMOTE CONTROL 11 The descriptions in this manual are based on the buttons of the remote control. Please read this manual carefully and use the Monitor set correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching and ends to the label inside the compartment, and close the battery cover. To remove the batteries, perform the installation actions in reverse. CAUTION Do not mix old and new batteries, as this yy may damage the remote control.
REMOTE CONTROL ENGLISH ENG AUTO Automatically adjusts picture position and minimizes image instability.(RGB input only) INFO Displays the input information. SETTINGS Accesses the main menus or saves your input and exit menus. W.BAL Enters the White Balance menu. S.MENU (SuperSign Menu Key) This button does not apply to this model. OK Selects menus or options and confirms your input. Navigation Buttons Scrolls through menus or options.
MAKING CONNECTIONS AUDIO IN VIDEO OUT NOTE Connect the signal input cable yy and tighten it by turning the screws clockwise.
MAKING CONNECTIONS Connecting the Power Cord ENGLISH ENG Power Button 2 1 Connecting the External devices HD Receiver HDMI DVI AV Component DVD VCR HDMI DVI AV Component Speaker AV Component Memory storage USB PC HDMI DVI RGB LAN Display Port Camcorder/ Camera HDMI DVI AV Component Gaming device HDMI AV Component
MAKING CONNECTIONS 15 Daisy Chain Monitors Monitor 1 Monitor 2 Monitor 3 Monitor 4 ENG ENGLISH DP Cable Use the cable provided with the product or use a DisplayPort certified cable version 1.1a or higher.
MULTIVISION CONFIGURATION ENGLISH ENG MULTIVISION CONFIGURATION Function Setting 3 Set ID setup for each set. (* The model 55LV75A does not support any functions for controlling the Fan.) 1 IR Receiver connection. Back of the product. OPTION Move OK • Language • ISM Method : Normal • DPM Select : 5 sec. • Fail Over : Off • Factory Reset • Set ID :1 ◀ • Tile Mode 1ꔋ ▶ Close • PIP/PBP • Fan • USB Content Recovery : Off • SIMPLINK • Product/Service Info.
MULTIVISION CONFIGURATION 17 6 Connect the Monitor sets, in series, using an RS-232C cable. ENG ENGLISH Monitor 1 Monitor 2 Monitor 3 Monitor 4 RS-232C Cable 7 Installation Menu setup. Installation Menu (V 2.21) LG Digital Signage Setup White Balance Adjust Password Change Configuration Cloning Set ID Setup OK 8 Tile Mode setup. (* The model 55LV75A does not support any functions for controlling the Fan.) OPTION Move OK • Language • ISM Method : Normal • DPM Select : 5 sec.
MULTIVISION CONFIGURATION Setting the Tile Mode ENGLISH ENG In Tile Mode you can view an image in a larger scale by connecting multiple monitors. 1X2 When using 2 monitors OPTION Move Tile ID 2X2 When using 4 monitors OK • Language • ISM Method : Normal • DPM Select : 5 sec. • Fail Over : Off • Factory Reset • Set ID :1 • Tile Mode • PIP/PBP • Fan • USB Content Recovery : Off • SIMPLINK • Product/Service Info. Tile Tile Mode Auto Config.
MULTIVISION CONFIGURATION 19 Setting the Picture ID The IR signal of the remote control is yy transmitted through the RS-232C cables connected in serial mode. When you set a Picture ID using the remote yy control, you can only control the Set that matches the Picture ID. ex) For example, if you set a Picture ID to 2, you can only control the monitor with the Set ID 2. If Picture ID is set to Off, you can control all monitors at the same time.