INSTALLATION MANUAL LED TV* Please read this manual carefully before operating your set and retain it for future reference. UV3***-U* 75/86UU3***-U* www.lg.
TABLE OF CONTENTS ENG ENGLISH TABLE OF CONTENTS 3 LOCATION AND FUNCTION OF CONTROLS 3 Parts and Button 4 EZMANAGER 4 LANGUAGE & COUNTRY SELECTION 5 INSTALLATION MENU 5 6 6 6 7 7 8 9 9 9 9 9 10 10 10 11 11 12 12 14 14 14 15 16 17 17 17 17 18 18 INTRODUCTION PUBLIC DISPLAY SETTINGS - Public Display Settings Operation - Power On Status - Volume - Key Management - Limited Mode - DTV Channel Update - Power On Default - Aux Source Setting - Power Management - Factory Reset NETWORK - MAC Address -
LOCATION AND FUNCTION OF CONTROLS Parts and Button ••Image shown may differ from your TV. Screen Remote control and Intelligent1 sensors Power Indicator Button2 Button2 1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. 2 Button - This button is located below the TV screen. NOTE ••You can set the power indicator light to on or off by selecting General in the main menus.
EZMANAGER ENG ENGLISH EzManager ••Image shown may differ from your TV. LANGUAGE & COUNTRY SELECTION -- Please select the Language and Country. Some countries need to select the Time Zone.
INSTALLATION MENU 5 ••Image shown may differ from your TV. INTRODUCTION The abundant functions for Hotel TV linked with software installation can be projected on OSD as ‘Installation Menu’. The wide range of hotel features can be performed simply on additional window to enhance the LG hotel TV’s easy installation and convenient operation for Hotelier and System Integrators.
INSTALLATION MENU PUBLIC DISPLAY SETTINGS ENG ENGLISH 1 Use the button to select the PUBLIC DISPLAY SETTINGS. 2 Use the ‘OK’ button and then button to select Public Display Mode. -- When ‘Public Display Mode’ is set to On (Work), all functions of Public Display Mode apply.
INSTALLATION MENU 7 -- Decide to apply volume policy of ‘Start Volume’, ‘Maximum Volume’ and ‘Minimum Volume’ as On(Work) or Off(Do Not Work). -- (0 ≤ Min ≤ Start ≤ Max ≤ 100) Start Volume ••This entry sets the start volume level when is power on. -- The level is specified as a number between minimum volume to maximum value. (Min ≤ Start ≤ Max) -- The default setting is ‘Off’ (disabled).
INSTALLATION MENU ENG ENGLISH Limited Mode -- Configure TV function’s limitation. When selected to ‘On’, following sub-menus will be worked by below. Setup Menu -- Permit to tune and manage Channels as ‘On’(permitted) or ‘Off’(not permitted). Channel Change ••Decide to change channel or not by setting ‘Program Change’ as ‘On’(Change Possible) or ‘Off’(Change Impossible) when present source is TV. -- When ‘Channel Change’ is set to Off (Change Impossible) »» Program Key, Numeral Key, List Key, Q.
INSTALLATION MENU 9 -- It is a mode to set whether to update dtv Channel automatically or not. -- When DTV Channel Update is set to ‘Auto’, the function to update TV’s Channel map according to dtv Channel’s stream information. -- DTV Channel Update is set to ‘Manual’, the function to keep TV’s Channel map even though dtv Channel’s information is changed. Power On Default -- Set the channel to display and Volume Level, etc. when turn on power in AC Power On or Standby status.
INSTALLATION MENU ENG ENGLISH NETWORK (Depending on model) 1 Use the button to select the NETWORK. MAC Address -- Displays the MAC address (not customizable). Network Setting One-click network connection -- Connects easily to a wired/wireless network. -- Network Connection to connect to an available network automatically. Follow the prompts on the TV. To connect to a network through Set Expert -- For use in special circumstances such as in offices (in cases where a static IP is used).
INSTALLATION MENU 11 ••Sets the Wake On LAN function to Enable or Disable. -- The Wake On LAN feature enables the TV to receive software updates and/or be powered ON upon receipt of Wake Up Frame packets and/or Magic Packet data via the wired LAN. To facilitate use of this feature, note that the appropriate wired connection must be made. (‘Wake up Frame’ is not supported depending on model) Server Settings ••Sets the information to connect to the external server.
INSTALLATION MENU ENG ENGLISH GENERAL Configuration Setup Select RCU -- It is a mode to set whether to use Select RCU or not. When ‘Select RCU’ is set to ‘Enable’, You can adjust ‘Number of RCU’ menu. Number of RCU -- It is a mode to set Number of RCU. Number of RCU value range 1~9. (When ‘Select RCU’ is set to ‘Enable’) Number of RCU value range 0. (When ‘Select RCU’ is set to ‘Disable’) * RCU(Remote Control Unit) : It is special RCU that operates only setted number of RCU in TV.
INSTALLATION MENU 13 (Depending on model) -- When ‘USB Auto Playback’ is set to ‘Movie’, TV finds and plays the USB’s movie files located at the root(top) directory Movies if USB is plugged in. -- When ‘USB Auto Playback’ is set to ‘Photo’, TV finds and plays the USB’s photo files located at the root(top) directory Photos if USB is plugged in.
INSTALLATION MENU ENG ENGLISH External Speaker Volume Control -- Selects the volume control method of an external speaker. You can select ‘Off’, ‘Int Variable’,’ Fixed.’,’Ext Variable’ by ^ pressing button. Ext Variable uses the External Vol Up/Down Control Line to change the volume up to 1 Watts. Int variable is linked to the main volume OSD and change the volume 0 - 1 Watts. Fixed produces a fixed output. The default is Off. Output -- This item is enabled when Volume Control is set to Fixed.
INSTALLATION MENU 15 CEC Mode -- You will have 3 modes to choose [Default], [HCEC] and [TVLink-CEC]. -- If [Default] is selected, you can use SIMPLINK which is provided in LG TV. Also you can enable and disable SIMPLINK through SIMPLINK MENU. -- If [HCEC] is selected, you can use TVLink-HCEC Protocol. For more detailed information, please refer to TVLink-HCEC Protocol document) -- If [TVLink-CEC] is selected, TV will not directly work for key input except for power key.
INSTALLATION MENU ENG ENGLISH StandBy -- Set the sending and receiving scenario of OpStandBy(0x0c) command. -- Ths detailed scenario is described on the table below. Send Receive Send Only O X Receive Only X O All O O Off X X Forced Initialize -- This setting will be enabled When CEC mode is set as ‘TVLink-CEC’ -- If ‘Enable” is selected, TV will change its input source to HDMI1 by any HDMI-CEC simulation from a device.
INSTALLATION MENU * Program/Frequency (Depending on model) -- You can select Program when Clock Source is 'TV' * Timezone(City) /Timezone(Custom) /Timezone(Offset) (Depending on model) -- In the case when there is difference between the time information received from the Teletext and the time of the current area, it can be set up to correct this. The initial value is 0, and it can be changed in the range of -12Hrs ~ +14Hrs.
INSTALLATION MENU ENG ENGLISH * Reset -- Delete Downloaded video file * Operation -- The video displays after your TV is turned on and the boot logo appears -- If Welcome Video is enabled and a video is downloaded on the TV, the video plays -- The time it takes a video to be displayed may differ depending on the decoding time of the video. -- Controls for playing the video are not available. (Pause, stop, fast forward, etc.
INSTALLATION MENU 19 -- Ez Download is a function that enables users to download the desired items all at once, such as EPK (software update file), TLL, Logo Image, Background Images, Micom. * Images and EPK files should be copied into the folder named LG_DTV on the USB. -- TLL files should be copied to the root folder of the USB. -- If you press ‘EZ Download’ menu, EZ Download is launched. -- If .DZM file exist file will be selected previously download file.
INSTALLATION MENU ENG ENGLISH Logo Image Download -- If there are more than two USB Memory Device, It is possible to select the USB. -- The download sequence is Logo Image Download -> Select Image -> UPDATE. NOTE ••Splash Image update function supports only JEPG,BMP format file of less than 8 MB filesize. ••We recommend you that splash image resolution match the TV`s panel resolution. ••Max resolution of splash image : Full HD → 1920 x 1080, HD → 1360 x 768.
INSTALLATION MENU -- This feature update EPK of TV through the hex file in USB. The target file is located in \LG_DTV folder. -- If there are more than two USB memory Device, It is possible to select the USB. -- The download sequence is Update TV Software -> Select file(EPK) -> UPDATE.
INSTALLATION MENU ENG ENGLISH Update Micom Software -- This feature update MICOM of TV through the txt file in USB. The target file is located in \LG_DTV folder -- If there are more than two USB memory Device, It is possible to select the USB. -- The download sequence is Update Micom Software -> Select file(Micom) -> UPDATE.
INSTALLATION MENU 23 -- Once the internal TV data and its channel map information is written to the USB memory card, the user can start “Import Clone File” process with the data file generated and stored in USB memory card. As previously warned in “Export Clone File” process, the user should not turn TV off nor unplug the USB memory card. The following images might be slightly different than the OSD image.
INSTALLATION MENU ENG ENGLISH Export Clone File -- "Export Clone File” must be done first before “Import Clone File” process, as it generate the file to be used in “Export Clone File”. While writing is in process, the user must not turn TV off nor unplug the USB memory card. The following images might be slightly different than the OSD image.