OWNER’S MANUAL Safety and Reference LED TV* * LG LED TVs are LCD TVs with LED backlighting. Please read this manual carefully before operating your TV and retain it for future reference. 43UV340C 43UV340H 49UV340C 49UV340H *MFL69885532* 55UV340C 55UV340H 55UV342H 65UV340C 65UV340H 75UV340C www.lg.com P/NO : MFL69885532 (2001-REV06) Copyright © 2018 LG Electronics Inc. All Rights Reserved.
Warning! Important Safety instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. ••Only use attachments/accessories specified by the manufacturer. ••Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
••Outdoor Antenna Grounding (Can differ by country): If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded to provide some protection against voltage surges and built-up static charges.
ENGLISH ••When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV. ••Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen. ••DISCONNECTING THE DEVICE FROM THE MAIN POWER The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible. ••Make sure the power cord is connected securely to the power plug on the TV.
••When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. (Depending upon model) ••Make sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward after being installed.) ••Do not fasten the screws with excessive force otherwise they may be worn out and become loose. ••Make sure to wring any excess water or cleaner from the cloth.
Adjusting the Menu When the TV is turned on, press the button one time. You can adjust the Menu items using the buttons. Turns the power off. Changes the input source. Adjusting the Angle of the TV to Suit View (Depending upon model) Swivel 20 degrees to the left or right and adjust the angle of the TV to suit your view. Scrolls through the saved channels. 20˚ Adjusts the volume level. 20˚ Mounting on a Table (Depending upon model) 1 Lift and tilt the TV into its upright position on a table.
Securing the TV to a Wall (optional) [TYPE 2] (Depending upon model) 2-Screws, 2-Washers, 2-Nuts (provided as parts of the product.) Stand Desk The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com. Connect the Kensington security system cable between the TV and a table. ••The Kensington security system is optional.
10 cm (4 inches) 10 cm 10 cm Connections (Notifications) 10 cm ENGLISH Make sure to use screws and wall mounts that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.
••Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV. ••Use a signal splitter to use 2 TVs or more. ••DTV Audio Supported Codec: MPEG, Dolby Digital ••This TV cannot receive ULTRA HD (3840 x 2160 pixels) broadcasts directly because the related standards have not been confirmed. (Depending upon model) A Other Connections Remote Control (Some buttons and services may not be provided depending upon models or regions.
Settings To select Picture Mode B B Changes the picture mode. ENGLISH Shows information on the current program. Changes the sound mode. Accesses the setting menu. Accesses the quick menu. Navigation button (up / down / left / right) Scrolls through menus or options. Selects menus or options and confirms your input. Returns to the previous screen. Clears all on-screen displays and returns to TV viewing. Enables SAP (Secondary Audio Program) Feature. Sets the length of time until the TV to turns off.
To set additional picture options • Picture • Picture Mode Settings • Picture Options Adjusts detailed setting for images. ••Noise Reduction Eliminates noise in the picture. ••MPEG Noise Reduction Eliminates noise generated while creating digital picture signals. ••Black Level Adjusts the brightness and contrast of the screen to suit the black level. ••Real Cinema Optimizes the screen for movie viewing.
Open Source Software Notice Information To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
Specifications HDMI (DTV) supported mode Resolution Product specifications may be changed without prior notice due to upgrade of product functions. Estimated yearly energy consumption indicated on the FTC label is measured in accordance with the Test Procedures for Television Sets (USA only). The actual energy consumption depends on the usage environment (The content watched, TV settings, etc.).
Component port connecting information (Depending upon model) Supported Audio Formats File Format Component ports on the TV Y PB PR Video output ports on DVD player Y Y Y Y PB B-Y Cb Pb PR R-Y Cr Pr .mp3 .wav Component supported mode Horizontal Frequency (kHz) 15.73 720 x 480i 15.75 720 x 576i 15.62 31.47 720 x 480p 31.50 720 x 576p 31.25 44.96 1280 x 720p 45.00 37.50 28.12 1920 x 1080i 33.72 33.75 56.25 1920 x 1080p 67.43 67.50 Resolution ENGLISH Vertical Frequency (Hz) 59.94 60.00 50.00 59.
Video MPEG-1, MPEG-2 Dolby Digital, MPEG-1 Layer I, Audio II, DVD-LPCM Video RV30, RV40 .rm, .rmvb Realaudio6 (cook), AAC LC, Audio HE-AAC Video H.264/AVC, HEVC .mkv, Dolby Digital, Dolby Digital .mp4, .ts Audio Plus, AAC .vob Regulatory FCC NOTICE High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. This device cannot be co-located with any other transmitter.
RSS-247 Requirement ENGLISH (For Canada) [For product having the wireless function using 5 GHz frequency bands] (1) the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (2) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p.
Key Codes ••This feature is not available for all models.
EXTERNAL CONTROL DEVICE SETUP (Image shown may differ from your TV.) ••Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series. ••Please be advised that not all models support this type of connectivity. ••Cable is not provided.
Set ID For Set ID number, see “Real Data Mapping”. 1 Press to access the main menus. 2 Press the Navigation buttons to scroll to General Set ID and press . 3 Press the Navigation buttons to scroll to SET ID and press . 4 Scroll left or right to select a set ID number and select , , . The adjustment range is 1-99. 5 When you are finished, press . * (Depending upon model) Customer Computer 1 5 6 9 RS-232C (Serial port) Pin name 3.
Communication Parameters Baud rate : 9600 bps (UART) Data length : 8 bits Parity : None Stop bit : 1 bit Communication code : ASCII code Use a crossed (reverse) cable. Command reference list (Depending upon model) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power* k a 00 to 01 02. Aspect Ratio k c (page 22) 03. Screen Mute k d (page 22) 13. Balance 04. Volume Mute k e k COMMAND1 COMMAND2 11. OSD k Select 12.
Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] [Set ID] : : [DATA] : [Cr] [ ] : : Second command to control the TV. You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
••Commands may work differently depending upon model and signal. 01. Power (Command: k a) ••To control Power *On or Off of the set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : *Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ••To Show TV is Power On or *Off Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x] * Similarly, if other functions transmit ‘FF’ data based on this format, Acknowledgement feedback presents status about each function. ENGLISH 02.
06. Contrast (Command: k g) ••To adjust screen contrast. You can also adjust contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] 11. OSD Select (Command: k l) ••To select OSD (On Screen Display) on/off when controlling remotely. Transmission [k][l][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Data 00 : OSD off Ack [g][ ][Set ID][ ][OK/NG][Data][x] Ack [l][ ][Set ID][ ][OK/NG][Data][x] 07. Brightness (Command: k h) ••To adjust screen brightness.
15. Equalizer (Command : j v) ••Adjust EQ of the set. Transmission [j][v][ ][Set ID][ ][Data][Cr] MSB 17. Control Backlight, Control Panel Light (Command: m g) * For LCD TV / LED TV ••To control the backlight. Transmission [m][g][ ][Set ID][ ][Data][Cr] LSB 0 0 0 0 0 Frequency 0 0 0 Data 7 6 5 Frequency 4 3 2 1 0 Step 0 0 0 1st Band 0 0 0 0 0 0(decimal) 0 0 1 2nd Band 0 0 0 0 1 1(decimal) 0 1 0 3rd Band ... ... ... ... ... ...
19. 3D (Command: x t) (only 3D models) (Depending upon model) ••To change 3D mode for TV.
IR OUT Using Guide (Depending upon model) Suitable / Not Recommend remote-controller data format Item Suitable Data Format Not Recommend Data Format Data format code Note NEC, Toshiba Full Repeat Code Format Philips RC5, RC6 Code Format Zenith Code Format Matsushita, RCA Code Format Sony 12/15/20 bit, Mitsubishi Code Format Single : Enable Repeat : Enable Single : Enable Repeat : Disable Single : Disable Repeat : Disable Sharp, JVC, R-step, Philips RCMM, RECS-80, XMP Code Format IR Receiver specifi
CHILD SAFETY: PROPER TELEVISION PLACEMENT MATTERS THE CONSUMER ELECTRONICS INDUSTRY CARES • Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. • As you enjoy your television, please note that all televisions – new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations.
Declaration of Conformity Trade Name LG Model 43UV340C-UB, 43UV340H-UA, 49UV340C-UB, 49UV340H-UA, 55UV340C-UB, 55UV340H-UA, 65UV340C-UB, 65UV340H-UB, 75UV340C-UB, 55UV342H-UD Responsible LG Electronics Inc. Party Address 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A TEL 201-266-2534 LG Customer Information Center For inquires or comments, visit www.lg.
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.
2 KEY CODES ENGLISH ENG KEY CODES • This feature is not available for all models.
EXTERNAL CONTROL DEVICE SETUP 3 • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series. * Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB USB IN IN 4 EXTERNAL CONTROL DEVICE SETUP (PC) (PC) (TV) (TV) RS-232C IN (CONTROL SERVICE) • You need to purchase the phone-jack to RS-232 cable required for &the connection between the PC and the TV, which is specified in the manual. RS-232C IN (PC) (PC) (CONTROL & SERVICE) * For other models, connect to the USB port. * The connection interface may differ from your TV.
EXTERNAL CONTROL DEVICE SETUP 5 • Baud rate : 9600 bps (UART) • Data length : 8 bits • Parity : None ENGLISH ENG Communication Parameters • Stop bit : 1 bit • Communication code : ASCII code • Use a crossed (reverse) cable. Command reference list (Depending on model) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power* k a 00 to 01 02. Aspect Ratio k c (p.7) 03. Screen Mute k d (p.7) k e 00 to 01 k f 00 to 64 06. Contrast k g 00 to 64 07. Brightness k h 00 to 64 08.
6 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
EXTERNAL CONTROL DEVICE SETUP 7 01. Power (Command: k a) ►► To control Power *On or Off of the set. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : *Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To Show TV is Power On or *Off Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x] * Similarly, if other functions transmit ‘FF’ data based on this format, Acknowledgement feedback presents status about each function. 02.
8 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 08. Color/Colour (Command: k i) 13. Treble (Command: k r) ►► To adjust the screen Color(Colour). You can also adjust colour in the PICTURE menu. ►► To adjust treble. You can also adjust in the AUDIO menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [i][ ][Set ID][ ][OK/NG][Data][x] 09. Tint (Command: k j) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu.
EXTERNAL CONTROL DEVICE SETUP * Analog Antenna/Cable ►► Adjust EQ of the set.
10 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG * Analog Antenna/Cable Data 00 : Physical Channel Number - Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) - Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125) [Data 01 ~ 04]: Major/Minor Channel Number Data 01 & 02: xx (Don't care) Data 03 & 04: xx (Don't care) Data 05: Input Source (Analog) - 00 : Antenna TV (ATV) - 01 : Cable TV (CATV) 2. Tune to the digital antenna (ATSC) channel 30-3.
EXTERNAL CONTROL DEVICE SETUP ►► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] * This feature is varied based on the model. Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data 05] [x][a][ ][Set ID][ ][NG][Data 00][x] 21. Channel(Programme) Add/Del(Skip) (Command: m b) ►► To skip current channel(programme) for next time.
12 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG * [Data 02], [Data 03] functions depend on model and signal. * If [Data 00] is 00 (3D On), [Data 03] has no meaning. 3) When [Data 00] is 06, 07 00 : Off 01 : On * If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data 03] works when 3D Mode (Genre) is manual only.
LED TV ENGLISH Easy Setup Guide Please read this manual carefully before operating your set and retain it for future reference. ESPAÑOL Guía Rápida de Configuración Lea atentamente este manual antes de poner en marcha el equipo y consérvelo para futuras consultas. FRANÇAIS Guide de configuration rapide Avant d’utiliser l’appareil, veuillez lire attentivement ce manuel et le conserver pour pouvoir vous y reporter ultérieurement.
ENGLISH Read Safety & Reference. ESPAÑOL Leer Seguridad y Consultas. FRANÇAIS Lisez Sécurité et références.
EXTERNAL SPEAKER OUT
HDMI IN
1 2 3 4
0 1 2 , , , , : mm (inches / pulgadas / po) , : kg (lbs / libras / lb) 43UV340C-UB 974 (38.3) 974 (38,3) 625 (24.6) 625 (24,6) 219.0 (8.6) 219,0 (8,6) 571 (22.4) 571 (22,4) 79.4 (3.1) 79,4 (3,1) 9.3 (20.5) 9,3 (20,5) 9.2 (20.2) 9,2 1.05 A / 105 W 1,05 A / 105 W (20,2) 49UV340C-UB 1,107 (43.5) 1 107 (43,5) 705 (27.7) 705 (27,7) 232.9 (9.1) 232,9 (9,1) 645 (25.3) 645 (25,3) 79.4 (3.1) 79,4 (3,1) 11.5 (25.3) 11,5 (25,3) 11.3 (24.9) 11,3 (24,9) 1.
0 1 2 75UV340C-UB 1,697 (66.8) 1 697 (66,8) 1,052 (41.4) 1 052 (41,4) 297.0 (11.6) 297,0 (11,6) 981 (38.6) 981 (38,6) 65.3 (2.5) 65,3 (2,5) 42.0 (92.5) 42,0 (92,5) 41.3 (91.0) 41,3 (91,0) 2.
*MFL69843832*