OWNER’S MANUAL Please read this manual carefully before operating your set and retain it for future reference. 55EG9600 55EF9500 55EG9200 65EG9600 65EF9500 *MFL68680222* www.lg.
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product. WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. yyDo not use this apparatus near water.
IMPORTANT SAFETY INSTRUCTIONS yyProtect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. yyOnly use attachments/accessories specified by the manufacturer. yyUse only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
IMPORTANT SAFETY INSTRUCTIONS yyDo not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit). yyGrounding (Except for devices which are not grounded.) Ensure that you connect the earthPower ground wire Supply Short-circuit to prevent possible electric shock (i.e., a TV with a Breaker three-prong grounded AC plug must be connected to a three-prong grounded AC outlet).
IMPORTANT SAFETY INSTRUCTIONS Preventing Image burn or Burn-in on your TV screen yyIf a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is image burn or burn-in and not covered by the warranty. yyIf the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.
IMPORTANT SAFETY INSTRUCTIONS FCC Radio Frequency Interference Requirements (for UNII devices) High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/ or damage this device. This device cannot be colocated with any other transmitter. FCC RF Radiation Exposure Statement [For having wireless function (WLAN, Bluetooth,...
IMPORTANT SAFETY INSTRUCTIONS Viewing 3D Imaging WARNING Viewing Environment yyViewing Time - When watching 3D contents, take five- to fifteen-minute breaks every hour. Viewing 3D contents for a long period of time may cause headache, dizziness, fatigue, or eye strain. Those that have a photosensitive seizure or chronic illness Symptoms which require discontinuation or refraining from watching 3D contents yyDo not watch 3D contents when you feel fatigue from lack of sleep, overwork or drinking.
LICENSES / OPEN SOURCE SOFTWARE NOTICE INFORMATION LICENSES Supported licenses may differ by model. For more information about licenses, visit www.lg.com . OPEN SOURCE SOFTWARE NOTICE INFORMATION ENGLISH ENG To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http://opensource.lge.com . In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.
TABLE OF CONTENTS 9 TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 28 29 5 6 6 6 6 7 - FCC Notice - Industry Canada Statement - IC Radiation Exposure Statement - Note to Cable/TV Installer - LG Recycling Policy Viewing 3D Imaging 30 30 31 32 Connecting to a PC - HDMI Connection or DVI to HDMI Connection Connecting to an Audio System - Digital Optical Audio Connection Connecting Headphones Connecting a USB Drive 33 MAGIC REMOTE FUNCTIONS 8 LICENSES 34 34 34 Registering Magic Remote How to Use M
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING INSTALLATION PROCEDURE 1 Open the package and make sure all the accessories are included. 2 Attach the stand to the TV set. 3 Connect an external device to the TV set. 4 Make sure the network connection is available. You can use the TV network functions only when the network connection is made. * When the TV is turned on for the first time after being shipped from the factory, initialization of the TV may take approximately one minute.
ASSEMBLING AND PREPARING Magic Remote, Batteries (AA) (See page 33.) Owner’s Manual P Cinema 3D Glasses The number of 3D glasses may differ depending upon the model or country. Cable Holder (See page 21.) (For 55EG9600) (For 65EG9600) Stand Base (See page 16, 17.) Stand Base (See page 17, 18.) (For 65EF9500) Stand Base (See page 18, 19.) Stand Base (See page 19, 20.) (For 55EG9200) Stand Base (See page 16, 17.) (For 55EG9600, 55EG9200) Component Video Cable (See page 26.
ASSEMBLING AND PREPARING Optional Extras Optional extras can be changed or modified for quality improvement without any notification. Contact your dealer for buying these items. These devices work only with certain models. The model name or design may be changed manufacturer’s circumstances or policies.
ASSEMBLING AND PREPARING 13 Parts and Buttons Screen Speakers Remote Control Sensor Joystick button2 Intelligent Sensor1 (Depending upon model) 1 Intelligent sensor - Adjusts the image quality and brightness based on the surrounding environment. 2 Joystick button is located below the screen of TV. NOTE yyYou can set the LG Logo Light to be on or off by selecting GENERAL in the main menus.
ASSEMBLING AND PREPARING Using the Joystick button You can operate the TV by pressing the button or moving the joystick left, right, up, or down. Basic functions Power On When the TV is turned off, place your finger on the joystick button, press it once, and release it. Power Off When the TV is turned on, place your finger on the joystick button, press it once for a few seconds, and release it. All running apps will close.
ASSEMBLING AND PREPARING Lifting and Moving the TV When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size. 15 yyUse at least two people to move a large TV. yyWhen transporting the TV by hand, hold the TV as shown in the following illustration. CAUTION yyAvoid touching the screen at all times, as this may result in damage to the screen.
ASSEMBLING AND PREPARING Setting Up the TV You can mount your TV to a wall or attach the stand if you wish to place the TV on an entertainment center or other furniture. Attaching the Stand If you are not mounting the TV to a wall, use the following instructions to attach the stand. CAUTION yyMake sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward after being installed.
ASSEMBLING AND PREPARING 17 (For 65EG9600) 3 1 Packing Brace Stand Cover CAUTION 5 EA M4 x L20 4 2 Stand Cover Stand Base Cover Holder 1 Insert the protruding parts of the stand cover into the holes. 2 Insert the cover holder of the stand cover into the holes until it clicks. 3 Press the stand cover gently so that the nonwoven fabric inside is attached tightly.
ASSEMBLING AND PREPARING (For 55EF9500) 3 1 Stand Cover 8 EA M4 x L20 CAUTION 4 ENGLISH ENG yyDo not place the TV without the stand attached into its upright position. The protruding Joystick Button may be damaged. yyUse a flat tool to remove the stand cover. 2 Cover Holder 1 Insert the protruding parts of the stand cover into the holes. 2 Insert the cover holder of the stand cover into the holes until it clicks.
ASSEMBLING AND PREPARING 19 (For 65EF9500) 3 1 Stand Cover 5 EA M4 x L14 CAUTION 4 2 Cover Holder 1 I nsert the protruding parts of the stand cover into the holes. 2 Insert the cover holder of the stand cover into the holes until it clicks. Stand Base ENGLISH ENG yyDo not place the TV without the stand attached into its upright position. The protruding Joystick Button may be damaged. yyUse a flat tool to remove the stand cover.
ASSEMBLING AND PREPARING Mounting on a Table 3 (Image shown may differ from your TV.) 1 Lift and tilt the TV into its upright position on a table. 10 - Leave a 10 cm (4 inches)cm(minimum) space from the wall for proper ventilation. 10 cm 10 cm 10 cm 10 cm (4 inches) 8 EA M4 x L14 10 cm 10 cm 10 cm 4 ENGLISH ENG 2 Connect the power cord to a wall outlet. Cover Holder 1 2 Insert the protruding parts of the stand cover into the holes.
ASSEMBLING AND PREPARING Securing the TV to a wall (optional) (Depending upon model) Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. - If there are bolts inserted at the eye-bolts position, remove the bolts first. 2 Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV. 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope or cable.
ASSEMBLING AND PREPARING Mounting on a Wall A An optional wall mount can be used with your LG Television. Consult with your local dealer for a wall mount used by your TV model. Carefully attach the wall mount bracket at the rear of the TV. Install the wall mount bracket on a solid wall perpendicular to the floor. If you are attaching the TV to other building materials, please contact qualified personnel to install the wall mount. Detailed instructions will be included with the wall mount.
MAKING CONNECTIONS 23 MAKING CONNECTIONS You can connect various external devices to the TV. Supported external devices are: HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices. For more information on external device’s connection, refer to the manual provided with each device. NOTE yyIf you record a TV program on a DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR.
MAKING CONNECTIONS Connecting to a HD receiver, DVD Player, or VCR Connect a HD receiver, DVD Player, or VCR to the TV and select an appropriate input mode. NOTE yyHDMI specifications may be different for each input port, so make sure to check the device specifications before connecting. yyContact customer service for more information on the HDMI specifications of each input port. yyIf the device connected to Input Port also supports ULTRA HD Deep Color, your picture may be clearer.
MAKING CONNECTIONS 25 DVI to HDMI Connection Transmits the digital video signal from an external device to the TV. Connect the external device and the TV with the DVI-HDMI cable as shown in the following illustration. To transmit an audio signal, connect an audio cable. NOTE yyWhen using the HDMI/DVI cable, Single link is only supported.
MAKING CONNECTIONS Component Connection Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with a component cable as shown in the following illustration. NOTE yyIf cables are installed incorrectly, it could cause the image to display in black and white or with distorted color. yyCheck to ensure the cables are matched with the corresponding color connection. ENGLISH ENG YELLOW GREEN (Use the composite video cable provided.
MAKING CONNECTIONS 27 Composite Connection Transmits analog video and audio signals from an external device to the TV. Connect the external device and the TV with the composite cable as shown in the following illustration. NOTE yyIf you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the TV. yyCheck to ensure the cables are matched with the corresponding color connection. ENGLISH ENG YELLOW (Use the composite video cable provided.
MAKING CONNECTIONS Connecting to a PC NOTE ENGLISH ENG yyUse an HDMI connection for the best image quality. yyDepending upon the graphics card, DOS mode video may not work if a HDMI to DVI Cable is in use. yyIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.
MAKING CONNECTIONS 29 HDMI Connection or DVI to HDMI Connection Choose method A or B to make connection.
MAKING CONNECTIONS Connecting to an Audio System You may use an optional external audio system instead of the built-in speaker. Digital Optical Audio Connection Transmits a digital audio signal from the TV to an external device. Connect the external device and the TV with the optical audio cable as shown in the following illustration. NOTE yyDo not look into the optical output port. Looking at the laser beam may damage your vision.
MAKING CONNECTIONS 31 Connecting Headphones (For EG9600, EF9500 series) Listening to sound with headphones. NOTE yyDo not use headsets (earphones) at high volume or for a long time. It may cause damage to your hearing. yyAUDIO menu options are disabled when headphones are connected. yyWhen changing AV MODE with a headphone connected, the change is applied to video but not to audio. yyOptical Digital Audio Out is not available when connecting a headphone. yyHeadphone impedance: 16 Ω yyMax audio output: 0.
MAKING CONNECTIONS Connecting a USB Drive Connect a USB storage device such as a USB flash thumbdrive, external hard drive, or a USB memory card reader to the TV and access the SmartShare menu to use various multimedia files. NOTE yySome USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it directly to the USB port on the TV. yySome USB device may not work if it does not meet USB 3.0 standard. In case, connect it to USB IN 2 or USB IN 3 port.
MAGIC REMOTE FUNCTIONS 33 MAGIC REMOTE FUNCTIONS When the message Magic remote control battery is low. Change the battery . is displayed, replace the battery. To install batteries, open the battery cover, replace batteries (1.5 V AA) matching and ends to the label inside the compartment, and close the battery cover. Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution.
MAGIC REMOTE FUNCTIONS / USING THE USER GUIDE Registering Magic Remote How to register the Magic Remote (Wheel) To use the Magic Remote, first pair it with your TV. 1 Put batteries into the Magic Remote and turn the TV on. 2 Point the Magic Remote at your TV and press the Wheel (OK) on the remote control. * If the TV fails to register the Magic Remote, try again after turning the TV off and back on.
SPECIFICATIONS 35 SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions.
SPECIFICATIONS Wireless module (LGSBW41) Specifications Wireless Lan Bluetooth Standard IEEE 802.11a/b/g/n Standard Frequency Range 2400 to 2483.5 MHz 5150 to 5250 MHz 5725 to 5850 MHz Frequency Range Output Power (Max.) 802.11a: 11.5 dBm 802.11b: 11 dBm 802.11g: 10.5 dBm 802.11n - 2.4 GHz: 11 dBm 802.11n - 5 GHz: 12.5 dBm Output Power (Max.) Bluetooth Version 4.0 2400 to 2483.
MAINTENANCE / TROUBLESHOOTING 37 MAINTENANCE Cleaning Your TV Clean your TV regularly to keep it at peak performance and to extend the product lifespan. CAUTION yyMake sure to turn the power off and disconnect the power cord and all other cables first. yyWhen the TV is left unattended or unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges.
CHILD SAFETY: PROPER TELEVISION PLACEMENT MATTERS THE CONSUMER ELECTRONICS INDUSTRY CARES • Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. • As you enjoy your television, please note that all televisions – new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations.
Declaration of Conformity Trade Name LG Model 55EG9600-UA, 65EG9600-UA 55EF9500-UA, 65EF9500-UA 55EG9200-UA Responsible Party LG Electronics Inc. Address 1000 Sylvan Ave. Englewood Cliffs NJ 07632 U.S.A TEL 201 - 266 - 2534 The model and serial numbers of the TV are located on the back and one side of the TV. Record them below should you ever need service. MODEL SERIAL LG Customer Information Center For inquires or comments, visit www.lg.
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.
2 KEY CODES ENGLISH ENG KEY CODES • This feature is not available for all models.
EXTERNAL CONTROL DEVICE SETUP 3 • Image shown may differ from your TV. Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally. Note: The type of control port on the TV can be different between model series. * Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB USB IN IN 4 EXTERNAL CONTROL DEVICE SETUP (PC) (PC) (TV) (TV) RS-232C IN (CONTROL SERVICE) • You need to purchase the phone-jack to RS-232 cable required for &the connection between the PC and the TV, which is specified in the manual. RS-232C IN (PC) (PC) (CONTROL & SERVICE) * For other models, connect to the USB port. * The connection interface may differ from your TV.
EXTERNAL CONTROL DEVICE SETUP 5 • Baud rate : 9600 bps (UART) • Data length : 8 bits • Parity : None ENGLISH ENG Communication Parameters • Stop bit : 1 bit • Communication code : ASCII code • Use a crossed (reverse) cable. Command reference list (Depending on model) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Power* k a 00 to 01 02. Aspect Ratio k c (p.7) 03. Screen Mute k d (p.7) k e 00 to 01 k f 00 to 64 06. Contrast k g 00 to 64 07. Brightness k h 00 to 64 08.
6 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set can be controlled.
EXTERNAL CONTROL DEVICE SETUP 7 01. Power (Command: k a) ►► To control Power *On or Off of the set. Transmission[k][a][ ][Set ID][ ][Data][Cr] Data 00 : Power Off 01 : *Power On Ack [a][ ][Set ID][ ][OK/NG][Data][x] ►► To Show TV is Power On or *Off Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x] * Similarly, if other functions transmit ‘FF’ data based on this format, Acknowledgement feedback presents status about each function. 02.
8 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Data Min : 00 to Max : 64 * (Depending on model) Ack [i][ ][Set ID][ ][OK/NG][Data][x] 09. Tint (Command: k j) ►► To adjust the screen tint. You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data][x] 10. Sharpness (Command: k k) ►► To adjust the screen sharpness. You can also adjust sharpness in the PICTURE menu.
EXTERNAL CONTROL DEVICE SETUP 0 0 5th Band 0 0 1 0 1 20(decimal) Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] * It depends on model, and can adjust when sound mode is EQ adjustable value. 19. Energy Saving (Command: j q) ►► To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu.
10 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG Number - 22 : Antenna TV (DTV) – Don’t Use Physical Channel Number - 26 : Cable TV (CADTV) - Don’t Use Physical Channel Number - 46 : Cable TV (CADTV) – Use Major Channel Number Only (One Part Channel) Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0). * Tune Command Examples: 1. Tune to the Analog cable (NTSC) channel 35.
EXTERNAL CONTROL DEVICE SETUP ►► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data 00 : DTV 01 : CADTV 02 : Satellite DTV 10 : ATV ISDB-BS (Japan) 03 : ISDB-CS1 (Japan) 04 : ISDB-CS2 (Japan) 11 : CATV O 01 X X X 02 X X X 03 X O O [Data03][x] [t][ ][Set ID][ ][NG][Data00][x] 40 : Component1 60 : RGB 41 : Component2 90 : HDMI1 92 : HDMI3 91 : HDMI2 93 : HDMI4 26.
12 EXTERNAL CONTROL DEVICE SETUP ENGLISH ENG 27. Auto Configure (Command: j u) (Depending on model) ►► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
