Owner's Manual

PROGRAM
PLAY
-19-
The unit's advanced
programming system
enables
you
to
preset
the order
in
which
tracks are
played,
to
repeat
one track or all
tracks,
or to
repeat any segment
of a disc
without
regard
to track numbers.
Programming Play
Lists
To
program
the
order of
playback
for
the
tracks
on a
disc,
1.
Insert the
disc,
let the unit read the Table
of Contents
information,
and wait until the
disc has
stopped
and the number of
tracks and total
running
time is
displayed.
2.
Select the
deck
that
will
be
programmed
by pressing
the
CDP
Select button on the
remote for the
Play
Deck
or the
CDR
Select button on the remote for the
Record Deck.
3.
To
begin
the
programming sequence,
press
the
PROG.
button and note that the
PROG
Indicator
will
illuminate and the
Information
Display
will
show
00 00:00.
4.
Enter the track
numbers
to
be
played
by pressing
the
Numeric
Keys.
For
two-digit
track
numbers,
be certain to
enter the second
digit
within
three
seconds after the first number is entered.
As each track is
entered,
the
display
will
blink three
times,
alternating
between two
displays.
The first
display
will
show the track number
just
entered on the left side of the Information
Display
under the Track
Indicator,
while the
right
side
will
flash the number of
steps
that
have been
programmed.
For
example,
after
programming
the first
step
to be track
number
3,
the
display
will
flash
03 P-01.
Alternating
with
the track number and
program step
will
be a
display
of the track
and the total
running
time of all tracks that
have been
programmed
so far. For
example,
a
display
of
06 11:25 will
indicate that track
number six was the last track
programmed,
and that the total time of all tracks so far is
11
minutes and 25 seconds. The
TOTAL TIME
Indicator
will
flash
with
this
display
to remind
you
of the
display's
contents.
These
displays
will
alternate three
times,
and then show a
steady display
of the total
time and last track
programmed.
Continue to add tracks
in
the order
you
wish
to have them
played
until the
programming
session is
complete.
You
may
add
up
to 20
tracks,
repeating
a track
if
desired,
as
long
as the total number does not exceed 20.
If
you
exceed the 20 track
limit,
the
display
will
read FULL.
Tracks
may
also be added
using
the
NEXT[ ]
and
PREV.[ ]
buttons to
locate the
track,
and the
PROG.
button to
enter that track to the
programmed
sequence.
When
the
complete
list
of
tracks
has
been
entered,
press
the
PLAY[ ]
button.
The tracks
will
then
play
in
the order
they
have been entered.
Note that a
programmed
list of tracks
may
also be recorded
if
the disc
being
programmed
is
in
the
Play
Deck.
Follow the
instructions of the
explanation
for
recording
and
dubbing.
Checking, Editing
and
Clearing
Programmed Play
Lists
Once
you
have entered a
program
list
it will
remain
in
the unit's
memory
until the disc is
removed or the unit is turned off.
Thus,
if
you
play through
a
program
list,
simply press
the
PLAY[ ]
button
again
to
replay
the list.
If
you
find that
you
wish to check the list or
make
changes,
that is also
possible by
following
a few
simple steps.
To scroll
through
a
program
list,
press
the
PROG. CHECK
button. Each
press
of the button
will
move
through
the
tracks that have been
programmed.
The
display
will
alternate between the track
number of the
program step
number
(e.g.
12
P-03
tells
you
that track
12
on the disc is the
3rd
program step)
and the track number and
the total
running
time so far
in
the
program
(e.g.
12 16:04
tells
you
that at this
point you
have
programmed
a total of 16 minutes and
4
seconds of
material).
At
any point
in
the list
you may change
a
new
track
by simply entering
the track
number
using
the
Numeric
Keys.
Simply press
the buttons that
correspond
to
the number of the track
you
wish to
change.
To add a new
step
in
the
program,
1. Press
the
PROG. CHECK
button until
track
number 00
appears
on
the
Information
Display.
2. Add a new
track
by simply entering
the
track
number
using
the
Numeric
Keys.
You
may
add
up
to 20
tracks,
if
less than
20 tracks
in
the
program step.
To remove a
step
in
the
program,
1.
First use the
PROG. CHECK
button to
locate the track
you
wish to delete.
2.
Next,
press
the
CLEAR
button.
The information
in
the
display
will
blink
and the
step
will
be removed from the
program
list.
Program steps
need not be deleted
in
any
order;
as
long
as
you
have located a
step
in
the
program
list,
it
may
be erased.
To cancel an
entire
program
list
while
the
program
is
playing, press
the
PROG.
button
and note that the
PROG
Indicator
will
go
out.
To remove a
total
program
list
when
the
disc is
stopped, simply open
and close the
disc drawer. Whenever a disc is removed or
the unit is turned
off,
the
program
list is
erased.
PLAY( )
NEXT( )
CDR
CLEAR
PROG.
CDP
PROG. CHECK
PREV.( )
Numeric
Keys