ENGLISH ESPAÑOL Owner's Manual Air Purifier & Humidifier Read this owner's manual thoroughly before operating the appliance and keep it handy for reference at all times. www.LGSIGNATURE.com MFL69596002 Copyright © 2017 - 2018 LG Electronics. All Rights Reserved.
ENGLISH
Table of Contents Unpacking...........................................07 Parts.................................................................. 07 Removing Packing Materials............................. 08 Remote Control Setup....................................... 08 Installation...........................................10 Transporting or Moving the Product.................. 10 Installing the Product......................................... 10 Operation.............................................
Important Safety Instructions ENGLISH READ AND SAVE THESE INSTRUCTIONS. This guide contains many important safety messages. Always read and obey all safety messages. This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others, or cause damage to the product. All safety messages will be preceded by the safety alert symbol and the hazard signal word WARNING or CAUTION.
DISPOSAL •• If the product is submerged in water, stop using the product and contact an LG Electronics Customer Information Center for service. •• Dispose of all packaging materials promptly and keep them out of the reach of children. ENGLISH USE •• In the event of a gas leak (propane/LPG), ensure adequate ventilation and contact an authorized service center before resuming use. Do not touch the product or the power plug. •• Do not use an abrasive cloth or sponge, or a metal brush to clean the product.
ENGLISH Caution To reduce the risk of fire, electric shock, or personal injury when using the product, follow basic safety precautions, including the following: INSTALLATION •• Use the filter only for its intended purpose. •• Do not tilt the product while moving or cleaning it. •• Do not use detergents, cosmetics, chemicals, air fresheners, or disinfectants in the product. •• This product is not designed for use in mobile vehicles, including RVs or boats. •• Do not place the product within 3 ft.
Unpacking ENGLISH Parts Air purifier and humidifier Manual del propietario Remote controller / battery (CR2025, 1 EA) Ultra-fine cloth Owner's Manual •• The appearance or components of the product may differ depending on the model.
ENGLISH Removing Packing Materials Unpack the product and remove any packing tape or protective vinyl before using the product. 1 Take the product out of the box and remove the packing tape on the product. 2 Press the black button on the filter tray to slide the tray out. Remove the tray. 3 4 08 Remote Control Setup 1 Remove the remote controller's battery tray by pushing the release on the left of the tray and pulling out.
ENGLISH Warning •• A button/Coin-type battery is used in the remote control of the product. •• Do not swallow the battery. Otherwise, it may cause serious damage, including damage to your organs. •• If you swallow the battery, you may suffer organ damage within 2 hours. If serious, it may even cause death. •• Keep the battery out of children’s reach. •• If the battery tray is not fixed firmly, stop using the product and keep the battery tray out of children’s reach.
Installation ENGLISH Transporting or Moving the Product Caution Transport the product in a well-secured and upright position. Impacts may cause product damage. Installing the Product Caution Install the product on a strong, level surface. Installing the product on a weak or tilted surface may cause noise and vibration or tipping, resulting in injury. The product is heavy. Use two people when moving it. Dropping the product may cause personal injury or product malfunction. Allow a 4 in.
Operation ENGLISH Product Overview Front View Top cover (control panel and water level indicator light) Smart Diagnosis™ speaker Change product settings or check water level. Used when troubleshooting product malfunctions or failures. Refer to Smart Diagnosis™ on page 27. Easy-fill water bucket inlet Remote controller sensor panel Easily add water to the water bucket. Air outlet Vents purified air and moisture. Status display panel Check the product's settings and the air quality level.
ENGLISH Back View Humidity sensor Detects humidity level. •• Product will not work without the filters in place. PM1.0 (super ultra-fine dust) sensor •• Close outside doors and windows during use, if possible. To avoid high carbon dioxide levels, do not use for long periods in a tightly enclosed space. Detects dust density. Odor sensor •• The product cannot remove harmful CO (carbon monoxide) gas from the air. Detects odors in the air.
ENGLISH Control Panel and Water Level Indicator Start/Stop button Light button Starts or stops operation. Turns the air quality indicator light on/off. Mode button Humidity button Sets the operating mode. Sets the desired humidity level. (The humidity level can be set in 5% increments.) •• Press the button repeatedly to cycle through the operating modes from Purify → Humid Purify → Silent.
ENGLISH Status Display Panel Operating mode display Fan speed display Air quality display Display Icons Icon Description Water bucket's UV LED Lighting Water Treatment is running. Water bucket is full. Sleep timer display Turbo display Air quality monitoring function is ON. Hygiene drying function is ON. (Refer to page 22.) ON/OFF timer is activated using the LG Smart ThinQ application. Top cover is not properly mounted. The deodorizing Black Filter needs to be replaced.
Remote Controller Sensor Mode Speed Turbo Light ENGLISH Remote Controller Remote controller sensor panel 45 ˚ ˚ 45 Caution •• Do not step on or apply pressure. •• Do not store or use near water or in high humidity. Starts or stops operation. •• Do not store or use near an open flame or heating devices such as space heaters or ovens. The battery could explode. Mode button •• Remove the battery before storing to avoid damage from leaking battery fluid.
ENGLISH Purify Mode Humid Purify Mode This mode cleans and freshens indoor air. This mode improves indoor air using the humidifier and the air purifier. 1 Press the Start/Stop button on the machine or the remote controller. 1 Fill the water bucket before starting Humid Purify mode. 2 Press the Start/Stop button on the machine or the remote controller. 3 Press the Mode button to select Humid Purify mode. •• For details, refer to page 23.
This mode minimizes noise during air purification. Press Start/Stop to start operating, then press the Mode button to select Silent mode. •• Press the button repeatedly to cycle through the operating modes from Purify → Humid Purify → Silent. •• The mode shows in the status display panel. Note ENGLISH Silent Mode •• The default fan speed is Auto. Auto mode automatically adjusts the fan speed depending on the indoor air quality. •• The current fan speed appears in the status display panel.
ENGLISH Checking Air Quality Turning Air Quality Indicator Light On/Off The overall air quality is indicated by color in the status display panel and the air quality indicator light. While the product is operating, press the Light button to turn the overall air quality light on or off. Understanding Overall Air Quality The overall air quality is indicated using four levels, each using a different color. The overall air quality depends on both the dust density and the odor level.
The overall air quality is indicated by the color of the icon in the display. If the overall air quality is bad (orange) or very bad (red), the display also shows the cause. Note •• PM (particulate matter) density is displayed in increments of 1 unit, from 8 to 999. PM density values are based on the data sheet provided by the sensor manufacturer. •• The PM10 and PM2.5 air quality values follow those provided by the United States EPA (Environmental Protection Agency) for 2015.
ENGLISH Using Air Quality Monitoring Function Turn on the Air Quality Monitoring function to continuously measure and display the indoor air quality even when the product is turned off. Press and hold the Mode button for about 3 seconds. •• (monitoring) appears in the status display panel. Setting the Humidity You can select the desired humidity level when the product is operating in Humid Purify mode. Press the Humidity button while the product is in operation.
Control Lock Use the Off Timer button to set the product to Sleep mode and automatically turn off after a set number of hours. The Control Lock function locks all the control panel buttons, including the Power button, to prevent accidental operation by children or others. The controls can be locked even when the product is off. While the product is on, press the Off Timer button.
ENGLISH Hygiene Drying Function Counter Reset Function The Hygiene Drying function is turned on by default. After Humid Purify mode is used, the Hygiene Drying function runs the fan for 1 – 1 ½ hours to dry the water bucket filters and prevent the buildup of mold or bacteria. After replacing the deodorizing Black Filter, reset the usage time counter. •• When the Hygiene Drying function is running, drying) appears in the status display panel.
You can pour the water into the water bucket directly or through the Easy Fill Inlet. Using the Easy Fill Inlet Pouring Water into the Water Bucket If you want to add a large amount of water at once, pour the water into the water bucket directly. 1 To use, turn off the product, fill a container with water, and slowly pour the water into the inlet in the center of the top cover. Add water gradually until a chime sounds and the Full Water icon is lighted in the water level indicator.
ENGLISH Emptying the Water Bucket To empty the water bucket, turn off and unplug the product. Remove the top cover and lift out the water bucket. Place the bucket on a waterproof surface. Remove the top and side water bucket filters from the bucket. Tilt the bucket to empty it. •• The bucket empties from the slots midway up the sides. Make sure the slots are over the sink when emptying the bucket. Caution •• Do not allow water to sit for long periods in the water bucket.
Smart Functions Using the Wi-Fi Function Install the LG Smart ThinQ application on your smartphone to access the product's smart functions. The application can be found through the Google Play Store or Apple App Store. For more details on using the LG Smart ThinQ application, see the Help guide in the application. These directions apply only to models with Wi-Fi. 1 Open the LG Smart ThinQ application on your smartphone and select Product Registration.
ENGLISH Note •• Only the 2.4 GHz Wi-Fi frequency is supported. •• The Wi-Fi icon should appear in the product's display panel during the product registration. •• A wireless AP (access point) or router and internet cable are not included and must be installed before using the LG Smart ThinQ application. •• You can contact your ISP (internet service provider) to purchase and install a wireless AP.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Smart Diagnosis™ Should you experience any problems with your appliance, it has the capability of transmitting data to your smartphone using the LG Smart ThinQ application or via your telephone to the LG Customer Information Center.
ENGLISH Assistance with Smart Diagnosis™ If you need further assistance in troubleshooting the appliance, call an LG Customer Information Center at the number on the back cover of this manual. 1 When instructed to do so by the call center agent, press the Indicator button for about 5 seconds to start the Smart Diagnosis™ function. 3 Once the transmission has finished, resume your conversation with the call center agent, who will be able to assist you in using the information transmitted for analysis.
Maintenance •• Turn off and unplug the appliance before cleaning it. Otherwise, it may cause an electric shock. Part ENGLISH Scheduled Maintenance Caution Clean/Replace •• Do not spray water directly on the appliance. •• After cleaning, assemble in the reverse order of disassembly. –– Assemble the top cover, top water bucket filter, side water bucket filter, water bucket, and main body in the order shown.
ENGLISH Status Display Panel Error Codes Cleaning the Exterior The following error codes may be displayed on the status display panel. Clean the product's exterior with the ultra-fine cloth provided as an accessory. Error Code Action •• Properly mount the top cover on the main body. •• Check for foreign objects caught between top cover and main unit contact connector. •• Replace deodorizing Black Filter. •• Properly mount the top and side water bucket filters in the water bucket.
•• Remove the top cover before starting the cleaning process. 4 Dry the water bucket with a soft cloth. •• Use the ultra-fine cloth provided to dry the window on the bucket. 5 Rinse off the top and side water bucket filters with clean water. 6 To use the product immediately, shake off the excess water. If storing the product or not using it immediately, place the filters in a sunny spot and allow to dry completely. 7 Reassemble the water bucket filters in the water bucket.
ENGLISH Intensive Cleaning of Water Bucket Filters 1 Dissolve baking soda in water and soak the water bucket filters in the solution for 30 minutes. •• Use 6 ½ tbsp. (100 g) baking soda in 2 ½ gal. (10 L) water. 100 g (6 ½ tablespoons) 10L 60L (2 10L½ gal.) 2 Scrub the water bucket filters with a toothbrush or soft brush to remove any foreign objects. 3 Thoroughly rinse the filters to remove any baking soda residue.
Put the top cover back on. •• Align the top cover so that its contact connectors meet the contact connectors on the body of the product. 3 Place out of direct sunlight and allow to dry completely. 4 Reassemble the ultra fine filter (pre-filter) in the filter tray and insert the tray in the main body. ENGLISH 3 Contact connector (inside) •• Insert the ultra fine filter (pre-filter) in the tray with the handle facing up. If the filter or the tray are not assembled properly, status display panel.
ENGLISH Cleaning the PM 1.0 Black Filter 3 Place a new deodorizing Black Filter in the filter tray. •• Be sure to align the slots on the bottom of the deodorizing Black Filter with the tabs on the filter beneath it. 1 Press the filter tray release button to open the filter tray. 4 Insert the filter tray into the product. 2 Slide the filter tray out completely and remove the PM 1.0 Black Filter from under the deodorizing Black Filter. •• Do not attempt to separate the two sections of the PM 1.
Soak the filter in clean water and then rinse under running water to make sure no detergent residue remains. Caution •• Rinse thoroughly after washing until no detergent bubbles appear. Detergent residue left on the filter may shorten its lifespan or cause product malfunction. •• Take care not to damage the film or wires inside the filter during cleaning. If the filter is damaged, stop using the product and call for service. •• Do not attempt to disassemble the top and bottom sections of the PM 1.
ENGLISH 3 Insert the filter tray into the product. 3 Lift up and remove the Watering Engine™ from the water bucket. 4 Clean the Watering Engine™. Note Only use water to clean the sensor. Use of anything else may cause product failure. Cleaning the Watering Engine™ •• Wipe the interior and exterior with a soft cloth. •• Remove foreign objects in the holes using a paper clip or small brush. If water is not coming out of the Watering Engine™, it may need to be cleaned.
Run in air purifier mode for an hour or more on a sunny day. ENGLISH 1 •• This will help to remove moisture and mold from inside the product. 2 Turn off and unplug the appliance. 3 Cover the appliance with a dust sheet to prevent dust, bugs, or foreign objects from getting into it, and store it in a dry, shady spot. Caution Do not store the appliance in a wet or humid area, or in direct sunlight. Doing so may result in product deformation, malfunction, or mold growth and odor.
Before Calling for Service ENGLISH If you experience problems with the appliance, checking the following chart before calling for service may save you time and money. Problem Possible Causes Solution •• Correctly insert plug into outlet. Product is not working. Fan is noisy even on the lowest speed. Air purification does not work well. Product is making clunking sound. The overall air quality indicator light does not change color when there is a strong odor. 38 Power cord is unplugged.
The overall air quality indicator lamp stays red. Possible Causes Try moving the air purifier to a different room. Solution •• If the odor is very strong, the air purifier may not be able to remove it. •• Clean the sensor. •• Unplug the product, wait for 1 minute, then plug the product in again. Something was sprayed on or near the air purifier. •• Do not spray hair products, perfume, cleaners, cooking oil or other products near the air purifier. Control panel buttons do not work.
ENGLISH Problem The water bucket level does not change during Humid Purify mode. The air quality window is not clear or condensation is not forming during Humid Purify mode. Humidity level does not rise. Displayed humidity level does not agree with another device. 40 Possible Causes Solution Water bucket filters are not assembled properly. •• Properly assemble the top and side water bucket filters in the water bucket. The water bucket filters are dirty or clogged.
Possible Causes The product is new and recently installed. •• This is the smell of activated carbon (charcoal). It should dissipate after 1 – 2 weeks of use and is not harmful to humans. Product is used in smoky or smelly area. •• Product performance may suffer if used to replace a range hood or vent. Ventilate smoke or strong odors before using. Water in water bucket is contaminated with dirt, mold, or bacteria. An odor is coming from the air outlet or filter.
WARRANTY (USA) ENGLISH ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT REQUIRES YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT, UNLESS YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES” BELOW.
•• Damage or missing items to any display, open box, discounted, or refurbished product. •• Products with original serial numbers that have been removed, altered, or cannot be readily determined. Model and serial numbers, along with original retail sales receipts, are required for warranty validation. •• Increases in utility costs and additional utility expenses. •• Repairs when the product is used for other than normal and usual household use (e.g.
ENGLISH PROCEDURE FOR RESOLVING DISPUTES: ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY WAY TO THIS LIMITED WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING ARBITRATION, AND NOT IN A COURT OF GENERAL JURISDICTION. BINDING ARBITRATION MEANS THAT YOU AND LG ARE EACH WAIVING THE RIGHT TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS ACTION. Definitions. For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc.
Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration conducted solely on the basis of (1) documents submitted to the arbitrator, (2) through a telephonic hearing, or (3) by an in-person hearing as established by the AAA Rules. If your claim exceeds $25,000, the right to a hearing will be determined by the AAA Rules.
Memo
