Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set below. See the label attached on quote this information to your dealer if you service.
DLP PROJECTOR FCC NOTICE ? A Class B This digital device equipment has been to Part 15 of the interference in a tested and found to comply with the limits for a Class B digital device, pursuant FCC Rules. These limits are designed to provide reasonable protection against harmful residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Contents Contents Introduction Part Descriptions Main Body .......................................................7 Special Menu Options Selecting Language ........................................29 Using ARC Function........................................29 Flip horizontal Function ...................................30 Control Panel ..................................................8 XD Demo ........................................................30 Remote Control ................................
Safety Instructions Instructions Safety Please take note of the Instructions Safety instructions to safety are given prevent any potential accident in two forms as After The violation of this instruction may : reading this projector. detailed below. WARNING : The violation of this instruction may NOTES misuse of the or cause serious light injuries cause manual, keep it in the place that the user and injuries or always damage can even death. to the contact projector.
Safety Instructions WARNING Do not too many devices into plug It may result in overheating one of the outlet and outlet. fire hazard ! causes a NOTES Never touch the power a wet hand This may hazard ! Do not cord the or cause an plug with Hold the plug firmly when unplugging. If you pull the cord the cord may be damaged. electric shock This may in when the power the plug is damaged or plug connecting part of the power outlet is loose.
Safety Instructions WARNING Never touch the wall outlet when there is Do not of gas, open the windows and ventilate. leakage the drop This may cause projector allow or mechanical failure or impact shock. personal injury ! Itcancauseafireoraburnbya spark. NOTES Do not top of place heavy objects projector. Take on the the This may cause mechanical failure not to impact to lens particularly when moving projector. care Do not touch the lens of the projector.
Part Part Descriptions Main * Descriptions ENGLISH Body The projector is manufactured using high-precision technology. You may, however, see on the Projector screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the manufacturing process and does not always indicate a malfunction. Auto sliding *When the is door projector is turned opened automatically. on, auto sliding door Shutter *When the projector is turned opened automatically.
Part Descriptions Control Panel MENU Button SOURCE Button A OK Button FOCUS +/- Button ZOOM +/- Button POWER 8 Button
Part Descriptions ENGLISH Remote Control POWER POWER Button AUTO AUTO Button (Refer to SOURCE p.34) SOURCE Button D/EButton F/GButton STILL Button (Refer to MENU Button p.33) STILL MENU ARC Button BLANK Button KEYSTONE +/- Button FOCUS D / (Refer Button E (Refer to (Refer to p.31) p.31) to A BLANK ARC KEYSTONE FOCUS (Refer to p.29) OK Button OK ZOOM ZOOM +/- Button (Refer to p.21) p.
Part Descriptions Projector * Status Indicators Lamp Indicator, operation jector. indicator and temperature indicator on the projector show the Operation Lamp user Operation Indicator Orange(flashing) Off Power off. Green status of the pro- Indicator Standby. Lamp cooling until the lamp turn on. On operation.
Part Descriptions ENGLISH Accessories POWER AUTO SOURCE STILL MENU BLANK ARC KEYSTONE FOCUS OK ZOOM LIGHT 1.5V 1.5V Remote Control Computer Cable 2 Batteries (size AAA) RCA to D-Sub Video Cable Power Cord Adaptor Wall Operating guide * mounting Bolt and anchor bracket are included in the wall bracket. Optional * * * * Extras Contact your dealer to purchase these items. Contact your service personnel for replacing a new lamp.
Installing and Composition Installation and Composition Installation Instructions * Don't place the projector in the following conditions. It may Provide proper ventilation for this The projector is equipped with ventilation cause malfunction holes(intake) Never insert materials on Ensure good ventilation around the projector. The distance between the projector and the ceiling bottom should be more than 20cm/8 inches.
Installing Basic Operation of the Projector projector on a 2.Place the projector the correct distance from the wall. determines the actual size of the 3.Position the projector Composition ENGLISH 1.Place the screen and right angle, the screen image (Refer to page 31.) 4.Connect the cables of the a right angle will be crooked. If this is projector to a projector and the image. that the lens is set at so The distance between the screen.
and Installing Composition the Installing projector to the wall Safety Please take note of the Safety Instructions WARNING NOTES After : instructions to safety are instructions given in two forms as this manual, keep it in the the wall or misuse of the projector. detailed below.
Installing Accessories for wall and Composition bracket mounting ENGLISH Wall mounting bracket Bolts for wall Wall anchor bolt mounting bracket Wall Installing 1 Detach the mounting the Fixing Detach bracket from Wall product fixing mounting mounting wood a. Carefully place b. Insert the 2 c. projector Insert the with the the lens side down fixing product fixers on the * Fixing protect the lens from damage. top of the projector.(It's top that the point of fixer fig.
Installing 3 and Composition Insert anchors bolts for or O Check the surface O When the surface that the wall you can use the O Only making O Plasterboard is not anchors or wood into a wall, you bracket is concrete, bolts.
Installing 4 Install the wall Using bracket on mounting b. Insert the bolts for wall bracket mounting on the wall bracket Composition ENGLISH the wall the wall anchor bolt sleeves and bolts for wall Mount the wall a. mounting and as as mounting setting setting bracket the hole. the each hole. a b Bolt for wall Using O - the bolts for Only making After using wood into matching the mounting bracket the wood wall, you position of the can use.
Installing 5 O and Assemble the Assemble Get some b. Insert the After c. d. mounting bracket projector with the wall mounting bracket installed on the wall as below Fig. help from others. It may cause the product to fall and could cause injuries. 2 fixers product assembling Entirely with the wall projector a Hang fixing a. Composition on a bracket to the groove of the lower wall and check the upper groove.
Installing Adjusting - - Tilt and Composition Angle Adjustable angle range is 5°(upside/downside/left/right) and turn range is ±10. Do not adjust tilt angle with too much force. It may cause damage of product or could cause ENGLISH injuries. Adequate - Leave 16.8 mm installation space from the wall between the projector and the wall when installing the wall bracket on the wall. 16.
Installing and Composition Turning on the 1. Connect power cord Projector correctly. 2. Press the POWER button indicator flashes (Green operation When the remote control on control of the during cooling panel. lamp.) is turned on, auto projector sliding door and shutter are opened, automatically. display the picture after power on because the projector lamp operation indicator light turns (Green). It will take about 25 second to An or has to warm up.
Installing and Composition ENGLISH Focus, Zoom, Position of the Screen Image When an Adjust image appears the focus on the screen, check if it is in focus and fits the by using FOCUS button of the remote control or the control screen. panel. FOCUS Focus Adjust the screen size Zoom by using ZOOM button of the remote control or the control panel. FOCUS Focus If you want to adjust the Zoom screen image to upside/downside, adjust the lens shift as shown below.
Connection Connection Connecting to * You * Refer to page 41 for can connect the < How to connect a. Connect the projector to a computer that has VGA, SVGA, XGA the supported monitor displays of the projector. computer cable and SXGA output. to RGB Input (PC/DTV) of projector. cable to HDMI If PC Desktop > b. If the PC has DVI * a connecting output, Input the connect HDMI to DVI of the projector. HDMI, audio is not supported.
Connection ENGLISH Connecting * You to connect can a Video Source a VTR, a camcorder, a LDP any other or compatible video image source to the projector. a. Connect the Video input jacks output jacks of the A/V source of the projector to the with Video cable. b. Connect the S-Video S-Video input jack of the projector to the output jack of an A/V source with an S-Video cable.
Connection Connecting * * to a D-TV Box Set-Top To receive Digital TV (D-TV) programs, it is necessary to purchase a D-TV receiver (Set-Top Box) and connect it to the projector. Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and Set-Top Box. < How to connect a. Connect an RGB/HDMI computer cable (PC/DTV) of the b. If the D-TV D-TV source > to RGB Input projector.
Connection ENGLISH HDMI - - - HDMITM, the HDMI logo and High-Definition Multimedia Interface is registered trademark of HDMI Licensing." projector can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI). projector supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i This This a trademark or resolution.
Function Function * * * In this manual, the OSD(On Screen Display) may be different from your Projector's because it is just example with the Projector operation. If there is no input signal present, the Menu will not be displayed on the screen. This operating guide explains operation of RGB(PC) mode mainly. Video Menu Options Adjusting Video 1. Press the MENU button and then use D, E button to select the menu. Contrast 50 G Brightness 50 Reset 2.
Function ENGLISH Auto Color - Control Temperature To initialize values (reset to default settings), 1. Press the MENU button and then 2. Press the G button and then use use D , D, select the Normal option. E button to select the menu. E button to select ACC item. G ACC Gamma 3. Press the G button and then D E button to make use , appropriate adjustments. White peaking Color temp. Cool Normal 10 Warm Color enhancement 4. Press the A OK button to save.
Function White peaking Function 1. Press the MENU button and then 2. Press the G button and then D use D, use E button to select the E button to select White , menu. peaking item. ACC Gamma 3. Press the G button to F, adjust the screen condition White you want. as Color peaking 5 G temp. Color enhancement 4. Press the A OK button to save. Reset It's available to adjust [White peaking] in RGB(PC) and HDMI(DVI) The default value may changed based on input mode.
Function Menu Special ENGLISH Options Selecting Language 1. Press the MENU button and then use D, E button to select the menu. Language 2. Press the G button and then use D , E button to select Language to use D , E button to select the language horizontal Flip you want use. 4. Press the A OK button to Deutsch Francais Italiano Set ID Espanol Auto Svenska sleep Portugues save.
Function Flip * This function horizontal Function reverses the Use this function when projected image horizontally. rear projecting an image. 1. Press the MENU button and then use D, E button to select the menu. Language 2. Press the G button and then use D , E button to select Flip horizontal item. ARC G horizontal Flip To flip Demo 3. Press the G button to see reversed image. Set ID Each time you press the G button, the image will be reversed.
Function Menu Special Using Keystone * * Options function Use this function when the Only use of the the Keystone ENGLISH screen is not at right angle a function when you can't get the best projector and the image is a trapezoid shape. angle of projection, because it may cause a blazing fire screen. 1. Press the KEYSTONE + or KEYSTONE 2. Press the KEYSTONE + or KEYSTONE condition as Keystone You can - - button. button to adjust the screen you want.
Function Blank Selecting image color 1. Press the MENU button and then 2. Press the G button and then 3. Press the G button and then 4. Press the A OK button to Background this point. To exit the color will be use use use D , D , E button to select the E button to select Blank menu. image item. E button to select the color you want to use. Keystone 0 Blank image G Lamp mode Black Lamp time Green Tilt Blue Logo save.
Function ENGLISH Tilt function 1. Press the MENU button and then use D, E button to select the menu. Keystone 2. Press the G button and then 3. You can check tilt state of the use D , E button to select Tilt item. projector. Blank image Lamp mode Lamp time 0 X Tilt Y If tilt state is out of the safety area(avobe 15°), warning displayed and then To exit automatically, power turns off. the menu display, repeatedly, press message is Using the MENU button. Menu Prev.
Function Screen Menu Auto * Function configure This function assures you of synchronization of the Auto Tracking function * Options getting image. the best video works in RGB quality by automatically adjusting the difference of horizontal size and input only. 1. Press the AUTO button. Image positioning 2.
Function Using ENGLISH ZOOM function 1. Press the MENU button and then use D, E button to select the menu. Auto 2. Press the G button and then use D E button to select Zoom , +/- configure Manual item. configure Zoom +/- G FG 100% Position 3. Press the G button and then condition Zoom To exit G button to F, use zoom in or out the picture size Reset you want. as +/- range is 100% 250%. adjustment the menu display, repeatedly, ~ Menu press the MENU button. Prev.
RS-232C External Control Device * Connect the RS-232C control the Projector 's input jack to an external functions externally. Setup control device (such as a computer or a video control system) and SET ID 1. Press the MENU button and then 2. Press the G button and then use D use D, E button to select the menu. E button to select Set ID item. , Language ARC 3. Press the G button and then desired projector F, use G button to adjust Set ID to select the Demo ID number. 4.
RS-232C Command Reference List Command 1 Command 2 Data (Hexadecimal) Power 01. 02. k Select Input 0~1 a k b * * 03. Aspect Ratio k c 04. Screen Mute k d 0~1 05. Contrast k g 0~64 06. Brightness k h 0~64 07. Color k i 0~64 08. Tint k j 0~64 09. Sharpness k k 0~64 10. OSD Select k l 0~1 11. Remote Control Lock / k m 0~1 12. Color k u 0~2 13. Low Power j q 0~1 14. Auto configuration j u 1 Input Select x b * 15.
RS-232C 01. Power 03. (Command2:a) Aspect Ratio (Command2:c) To To control Power On/Off of the Projector. the adjust screen format. Transmission Transmission [k][c][][SetID][ ][Data][Cr] [k][a][][SetID][][Data][Cr] Data 0 Data Power Off : 1:PowerOn Ack 0 2 : 4 : Zoom1 5 : Zoom2 Screen( 4:3) Wide(16:9) Ack Power Off : : 8:FULL [a][ ][SetID][][OK][Data][x] Data Normal 1 1:PowerOn [c][ ][SetID][][OK][Data][x] To show Power On/Off status.
RS-232C 06. Brightness (Command2:h) To adjust screen 09. To brightness. Transmission * Min:0~Max:64 Refer to 'Real data mapping 1'. Ack Min:0~Max:64 Data * adjust the screen color. Transmission Min:0~Max:64 mapping 1'. [k][l][][SetID][][Data][Cr] Data Min:0~Max:64 08. Tint (Command2:j) adjust the screen Data OSD Off 1 : OSD On (OSD (OSD 0 : OSD Off 1 : OSD On (OSD (OSD 11.
RS-232C 12. Color Adjust Temperature (ACC) (Command2:u) the color temperature. : input source for the Set. Transmission [x][b][][SetID][][Data][Cr] [k][u][][SetID][][Data][Cr] 0 Input Select (Command1:x, Command2:b) To select Transmission Data 15.
Information Supported * The following table lists the formats display supported by the VGAEGA 640X350 70.090Hz 31.468kHz 640X350 85.080Hz 37.861kHz 640X400 70.090Hz 31.468kHz 640X400 85.080Hz 37.861kHz 720X400 70.082Hz 31.469kHz 720X400 85.039Hz 37.927kHz 640X480 59.940Hz 31.469kHz 640X480 72.800Hz 37.861kHz 640X480 75.00Hz 37.500kHz 640X480 85.008Hz 43.269kHz 800X600 56.250Hz 35.156kHz 800X600 60.317Hz 37.879kHz 800X600 72.188Hz 48.077kHz 800X600 75.
Information Maintenance * The on projector the needs little maintenance. You should screen. always If any parts need turn the power off and to be replaced, unplug the projector Clean the lens whenever you notice dirt or a soft, dry lint-free cloth. remove surface dirt To clean the the or 42 on the the Projector projector lint-free cloth. To Do not stains or or dust lens, moisten on a the surface of it.
Information Replacing the Lamp Last of The time unit Lamp ENGLISH replacement projector lamp usually lasts for about in the Selecting Function section. You 4000 hours. You must replace the can see lamp the used lamp when: The projected image gets darker or starts to be deteriorated. The lamp indicator is red. The message "Replace the lamp" appears on the screen when turning projector lamp on.
Information Replacing the Turn off the Lamp unplug cushioned surface that will from the power cable. the lens side down Carefully place 1 and projector on a 2 protect the lens damage. (Allow the lamp 3 lifting retaining driver or the Lamp lamp screws on similar driver or a fixing similar bolts of the lamp cover using a object. to cool for 1 hour before replacing it.
Information Memo 45
Information Memo 46
Information Specifications MODEL AN110B-JD/AN110W-JD resolution 1280(Horizontal) horizontal / vertical ratio DLP panel screen 15:9(horizontal:vertical) size 0.65 inches size 1.01~5.08m(40~200 inches) remote control distance 12m ratio 1:1.4 compatibility NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N zoom Video 768(Vertical)pixel x Power AC 200 - 240V~50/60Hz,1.3A-1A, 250W height(mm/inches) 254.4/10.0 breadth(mm/inches) 443.4/17.4 length(mm/inches) 93.9/3.
P/NO : 3828VA0577F