Model number Serial number : : LG DLP PROJECTOR Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the bottom of the set and quote this information to your dealer when you require service.
DLP PROJECTOR FCC NOTICE • A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ENGLISH Contents Contents Introduction Safety Instructions .......................................... 4 Part Descriptions Main Body ....................................................... Control Panel .................................................. Remote Control ............................................... Installing Batteries........................................... Projector Status Indicators.............................. Accessories.....................................................
Safety Instructions Safety Instructions Please take note of the safety instructions to prevent any potential accident or misuse of the projector. ➟ Safety Instructions are given in two forms as detailed below. WARNING : The violation of this instruction may cause serious injuries and even death. NOTES : The violation of this instruction may cause light injuries or damage to the projector. ➟ After reading this manual, keep it in the place that the user always can contact easily.
Safety Instructions WARNING ENGLISH Power Do not plug too many devices into one outlet. It may result in overheating of the outlet and causes a fire hazard ! Power Never touch the power plug with a wet hand This may cause an electric shock hazard ! Do not plug in when the power cord or the plug is damaged or the connecting part of the power outlet is loose. This may cause a fire or an electric shock hazard ! NOTES Hold the plug firmly when unplugging. If you pull the cord the cord may be damaged.
Safety Instructions Using Never touch the wall outlet when there is leakage of gas, open the windows and ventilate. WARNING Do not drop the projector or allow impact shock. This may cause mechanical failure or personal injury ! It can cause a fire or a burn by a spark. Using Do not place heavy objects on top of projector. This may cause mechanical failure or personal injury! NOTES Take care not to cause impact to the lens particularly when moving the projector. Do not touch the lens of the projector.
ENGLISH Part Descriptions Part Descriptions Main Body * The projector is manufactured using high-precision technology. You may, however, see on the Projector screen tiny black points and/or bright points (red, blue, or green). This can be a normal result of the manufacturing process and does not always indicate a malfunction.
Part Descriptions Control Panel MENU Button SOURCE Button A OK Button D / KEY STONE Button E / SMART IRIS Button G F / ZOOM + Button / ZOOM - Button POWER 8 Button
ENGLISH Part Descriptions Remote Control POWER POWER Button MENU Button F MENU SOURCE SOURCE Button / G Button AUTO Button (Refer to p.34) AUTO OK BLANK Button (Refer to p.32) D / A OK Button E Button ARC Button (Refer to p.30) STILL Button (Refer to p.33) BLANK ARC STILL KEYSTONE Button (Refer to p.32) KEYSTONE ZOOM ZOOM +/- Button (Refer to p.23) SMART IRIS Button (Refer to p.
Part Descriptions Projector Status Indicators * Lamp Indicator, operation indicator and temperature indicator on the projector show the user the operating status of the projector. Operation Indicator Lamp Indicator Temperature Indicator Operation Indicator Orange Green(flashing) Green Orange(flashing) Off Red Lamp Indicator Red(flashing) Green(flashing) Orange Temperature Indicator 10 Red Red (flashing) Standby. Lamp cooling until the lamp turn on. On operation.
ENGLISH Part Descriptions Accessories POWER MENU SOURCE AUTO BLANK KEYSTONE OK ARC STILL ZOOM SMART IRIS 1.5V 1.5V Remote Control 2 Batteries Power Cord Video Cable PROJECTOR Owner’s manual Computer Cable Owner’s manual CD ROM Wall mounting bracket * Bolt and anchor are included in the wall bracket. Optional Extras * * * * Contact your dealer to purchase these items. Contact your service personnel for replacing a new lamp.
Installing and Composition Installation and Composition Installation Instructions * Don’t place the projector in the following conditions. It may cause malfunction or product damage. Provide proper ventilation for this projector. ● The projector is equipped with ventilation holes(intake) on the bottom and ventilation holes(exhaust) on the front. do not block or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the projector.
ENGLISH Installing and Composition Basic Operation of the Projector 1.Place the projector on a wall. 2.Place the projector the correct distance from the screen. The distance between the projector and the screen determines the actual size of the image. 3.Position the projector so that the lens is set at a right angle to the screen. If the projector is not set at a right angle, the screen image will be crooked. If this is so then the keystone adjustment may correct this (Refer to page 32.) 4.
Installing and Composition Installing the projector to the wall Safety instructions on installing the wall Please take note of the safety instructions to prevent any potential accident or misuse of the projector. ➟ Safety Instructions are given in two forms as detailed below. WARNING : The violation of this instruction may cause serious injuries and even death. NOTES : The violation of this instruction may cause light injuries or damage to the projector.
Installing and Composition ENGLISH Accessories for wall mounting bracket Wall mounting bracket Bolts for wall mounting bracket Wall anchor bolt sleeves Bolts for fixing the bracket Fixing fixers Bolts for using the wood Installing Wall mounting bracket 1 Detach the products - Detach bolt from wall mounting bracket. - Detach product fixing bracket from Wall mounting bracket. Product fixing bracket Wall mounting bracket ➡ Press the upper of the wall bracket with both hands to tilt the bracket.
Installing and Composition 3 Insert anchors or bolts for using the wood after marking the positions where products are mounted on the wall Check the surface or thickness that the wall mounting bracket. When the surface that the wall mounting bracket is concrete, strong , weak natural rock, brick and hollow block, you can use the supplied anchors or bolts. Ó Only thickness of strike off material is less than 20mm, you can use the supplied anchors or bolts.
4 ENGLISH Installing and Composition Install the wall mounting bracket on the wall Using the wall anchor bolt sleeves and bolts for wall mounting bracket a. Mount the wall mounting bracket on the wall as setting the hole. b. Insert the bolts for wall mounting bracket as setting the each hole. a b Bolt for wall mounting bracket Using the bolts for using the wood Ó Only making wood into wall, you can use.
Installing and Composition 5 Ó Assemble the projector with the wall mounting bracket Assemble a projector with the wall mounting bracket installed on the wall as below Fig. Do not install this product by yourself. Get some help from others. It may cause the product to fall and could cause injuries. a. Hang fixing 2 fixers on a upper groove. b. Insert the product bracket to the groove of the lower wall mounting bracket. c.
ENGLISH Installing and Composition Cable Management 1 2 Place the set with the screen facing down on a cushion or soft cloth. Pull the back cover upward. Back panel of the set Connect the cables as necessary. Cable Holder At first, Bundle the HDMI, VIDEO, S-VIDEO Cables using the supplied Cable holder as shown. HDMI cable should be placed on the bottom.
Installing and Composition 3 Reinsall the back cover correctly and fix it using the thumb bolt. Thumb Bolt 4 Separate HDMI Cable and Power Code from others and then bind the cables as shown.
ENGLISH Installing and Composition Adjusting Tilt Angle - Adjustable angle range is 5°(upside/downside/left/right) and turn range is ±10. - Do not adjust tilt angle with too much force. It may cause damage of product or could cause injuries. Adequate installation space from the wall - Leave 16.8 mm between the projector and the wall when installing the wall bracket on the wall. 16.
Installing and Composition Turning on the Projector 1. Connect power cord correctly. 2. Press the POWER button on the remote control or control panel. (Green operation indicator flashes during cooling of the lamp.) ● ● An image will appear after the operation indicator light turns (Green). Select the source mode with the SOURCE button. * Don’t unplug the power cord while the ventilation fan (inlet/outlet) is working. If so, you take longer time by lamp on. Turning off the Projector 1.
ENGLISH Installing and Composition Focus, Zoom, Position of the Screen Image When an image appears on the screen, check if it is in focus and fits the screen. ● Adjust the focus by using FOCUS ring of the set. FOCUS Ring ● Adjust the screen size by using ZOOM+/- button of the remote control or the control panel. ZOOM If you want to adjust the screen image to upside/downside, adjust the lens shift as shown below.
Connection Connection Connecting to a Desktop PC * You can connect the projector to a computer of VGA, SVGA, XGA and SXGA output. * Refer to page 36 for the supported monitor displays of the projector. < How to connect > Connect computer cable to RGB IN (PC/DTV) of the projector. * You can get better picture quality when connecting HDMI source to the projector.
ENGLISH Connection Connecting to a Video Source * You can connect a VTR, a camcorder or any other compatible video image source to the projector. < How to connect 1 > a. Connect the Video input jacks of the projector to the output jacks of the A/V source with Video cable. < How to connect 2 > b. Connect the S-Video input jack of the projector to the S-Video output jack of an A/V source with an S-Video cable. * You can get better picture quality when connecting S-Video source to the projector.
Connection Connecting to a D-TV Set-Top Box * To receive D-TV programmes, it is necessary to purchase a D-TV receiver (Set-Top Box) and connect it to the projector. * Please refer to the owner's manual of the D-TV Set-Top Box for the connection between projector and D-TV Set-Top Box. < How to connect an RGB source > a. Connect RGB cable to RGB IN (PC/DTV) of the projector. b. Use a DTV receiver with DTV 480p(576p)/720p/1080i mode. * HDMI supports HDCP.
ENGLISH Function Function * In this manual, the OSD(On Screen Display) may be different from your Projector’s because it is just an example to help with the Projector operation. * If there is no input signal present, the Menu will not be displayed. * This operating guide explains operation of RGB(PC) mode mainly. Video Menu Options Adjusting Video < RGB mode > 1. Press the MENU button and then use F, G button to select the menu. 2. Press the D , E button to select a video item you want to adjust. 3.
Function Auto Color Temperature Control - To initialize values (reset to default settings), select the Normal option. 1. Press the MENU button and then use F, G button to select the D , E button to select ACC 2. Press the menu. ACC Gamma Brilliant Color TM White peaking Smart Iris item. 3. Press the F, G button to make desired adjustments. ● Each press of the D, E Cool ● button changes the screen as shown below.
ENGLISH Function White peaking Function 1. Press the MENU button and then use F, G button to select the 2. Press the D , E button to select White peaking menu. item. 3. Press the F, G button to adjust the screen condition as you want. Adjust to higher setting to achieve brighter picture. Adjust to lower setting for darker picture. ● To exit the menu display, repeatedly, press the MENU button. ● You can adjust White peaking only when Brilliant Color TM is On.
Function Special Menu Options Selecting Language 1. Press the MENU button and then use F, G button to select the 2. Press the 3. Press the ● ● D , E button to select Language F, G item. button to select the language you want to use. On-Screen-Display (OSD) is displayed in the selected language. To exit the menu display, repeatedly, press the MENU button. menu. Language ARC Overscan Flip horizontal Auto sleep MENU Prev. Using ARC Function 1. Press the ARC button.
ENGLISH Function Overscan Function 1. Press the MENU button and then use F, G button to select the menu. 2. Press the D , E button to select Overscan item. 3. Press the F, G button to select On or Off. ● You can adjust Overscan only in RGB-DTV, HDMI-DTV and Component mode. Language ARC Overscan Flip horizontal Auto sleep MENU Prev. D E F English G F 4:3 G F On G F Off G Move FG Select Flip horizontal Function * This function reverses the projected image horizontally.
Function Special Menu Options Using Keystone Function * Use this function when the screen is not at a right angle to the projector and the image is a trapezoid shape. * Only use the Keystone function when you can’t get the best angle of projection. 1. Press the KEYSTONE button. 2. Press the D , E button to select V Keystone or H Keystone. 3. Press the F, G button to make desired adjustments. ● Keystone can be adjusted from -20 to +20. ● You can also access this function via the MENU button.
ENGLISH Function Lamp mode Function 1. Press the MENU button and then use F, G button to select the 2. Press the D , E button to select Lamp mode menu. V Keystone H Keystone Blank image Lamp mode Lamp time item. 3. Press the F, G button to select High Bright or Economic. ● To exit the menu display, repeatedly, press the MENU button. MENU Prev. 0 0 F Logo G F High Bright G 11 Hr D E Move Select FG Checking Lamp time 1. Press the MENU button and then use F, G button to select the menu.
Function Screen Menu Options Auto Configure Function * This function assures you of getting the best video quality by automatically adjusting the horizontal size and synchronization of the image. * Auto Tracking function works in RGB PC input only. 1. Press the AUTO button. ● Image positioning and synchronization are automatically adjusted. Auto Configure 2. You want adjust more by various PC input modes, adjust Phase, Clock, Horizontal and Vertical in menu.
ENGLISH Function Using Horizontal Function 1. Press the MENU button and then use menu. F,G button to select the 2. Press the D,E button to select Horizontal item. 3. Press the F, G button to make desired adjustments. ● ● ● Horizontal adjustment range is -25 ~+25. To exit the menu display, repeatedly, press the MENU button. The variable range can be different depends on input resolutions.
Information Supported Monitor Display * The following table lists the display formats supported by the projector. Sources * * * * * Format Vertical Freq.(Hz) Horizontal Freq. (kHz) EGA 640X350 640X350 70.09Hz 85.08Hz 31.468kHz 37.861kHz PC98 640X400 85.08Hz 37.861kHz DOS 720X400 720X400 70.08Hz 85.03Hz 31.469kHz 37.927kHz VGA 640X480 640X480 640X480 640X480 59.94Hz 72.80Hz 75.00Hz 85.00Hz 31.469kHz 37.861kHz 37.500kHz 43.269kHz SVGA 800X600 800X600 800X600 800X600 800X600 56.
ENGLISH Information Maintenance * The projector needs little maintenance. You should keep the lens clean because any dirt or stains may appear on the screen. If any parts need to be replaced, contact your dealer. When cleaning any part of the projector, always turn the power off and unplug the projector first. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface of it. Wipe the lens surface gently with an air spray or a soft, dry lint-free cloth.
Information Replacing the Lamp Last of Lamp unit replacement The projector lamp usually lasts for about 2000 hours. You can see the used lamp time in the Selecting Function section. You must replace the lamp when: ● ● ● The projected image gets darker or starts to be deteriorated. The lamp indicator is red. The message “Replace the lamp” appears on the screen when turning the projector lamp on.
ENGLISH Information Replacing the Lamp 1 Turn off the projector and unplug the power cable. Carefully place the lens side down on a cushioned surface that will protect the lens from damage. (Allow the lamp to cool for 1 hour before replacing it.) 3 After lifting the lamp cover off, remove the two retaining screws on the lamp case with a screwdriver or similar objects. 2 Unscrew the fixing bolts of the lamp cover using a driver or a similar object.
Information Regarding the projector lamp control WARNING ● Don’t turn off the projector at least in 5 minutes after activating it. - The frequent On/Off changes may cause the lamp function to deteriorate. ● Don’t pull out the power cord while activating the projector and the cooling fan. - It may cause the lamp life-span to shorten and get damaged. ● The life-span of projector may considerably depend on the use environment and treatment conditions.
ENGLISH Information Memo 41
Information Memo 42
ENGLISH Information Specifications AN215 MODEL AN215-JD resolution 1280(Horizontal) x 720(Vertical)pixel horizontal / vertical ratio 16:9(horizontal:vertical) DLP panel size 0.62 inches screen size 1.53~11.65m(40~300 inches) remote control distance 12m zoom ratio 1:1.4 Video compatibility NTSC/PAL/SECAM/NTSC4.43/PAL-M/PAL-N Power AC 100 - 240V~50/60Hz, 3A-1A, 260W height(mm/inches) 285/11.3 breadth(mm/inches) 470.0/18.5 length(mm/inches) 107.8/4.
Skriv model- og fabrikationsnummeret på enheden ned herunder. Opgiv oplysningerne på mærkatet i bunden af enheden til din forhandler, hvis du får brug for service. Modelnummer Fabrikationsnummer : : LG DLP PROJEKTOR Du bedes læse denne brugervejledning grundigt igennem, førend du betjener enheden. Gem brugervejledningen til fremtidig brug.