Video Cassette Recorder OWNER'S MANUAL MODEL: CC490TW/CC290TW CC460TW/CC260TW CC450TW/CC250TW PAL BZ03 Before connecting, operating please read this instruction booklet Internet or adjusting this product, carefully and completely. Address:http://www.lg.
Position your VCR so that no sunlight falls directly onto it. Precautions&f Informatin bright light Just to or name a extraordinary few examples of the features: Care should be taken not to expose your VCR to any unnecessary vibration, moisture, dust or heat. electrical storms it is advisable to During the aerial cable and mains damage Do not to unplug both ? prevent accidental to your VCR and TV. ? except qualified service remove the back repaired by personnel.
Welcome to LG Thank you for buying this LG video cassette recorder Model CC490TW/CC290TW/CC460TW/ CC260TW/CC450TW/CC250TW.
Your video recorder (VCR) is designed so that almost all of its features can be controlled from the REMOTE CONTROL HANDSET. Some features can also be controlled from the FRONT PANEL of the video recorder. The maximum operating distance that you may control your video recorder is about 7.5 metres (25 feet). It must also be within an angle of 30 degrees either side of the REMOTE SENSOR on the front of your video recorder. RemotCnrl Locatin&Fu To avoid damage control handset for batteries from an safely.
Each button on your VCR has the same function its as corresponding button on the remote control handset. MODEL : CC490TW/CC290TW 123 POWER 4 5 6 MODEL 7 REW STOP/ 8 9 : Controls CC460TW/CC260TW 1234 5 11 10 6 FF EJECT POWER STOP/ EJECT PLAY REW 10 11 MODEL : FF 789 12 CC450TW/CC250TW 12 345 67 8 9 REW POWER FF 10 11 1. Power 2. Stop 3. Cassette 4. VCR 5. Remote Control Sensor 11. Channel 6. REC/ITR 12.
Make Conecting ToaTV one are made with both your VCR and additional appliance unplugged damaging your equipment. Connecting a VCR using a RCA lead is to achieve optimum sound and picture quality from video-tape playback. of the best ways The quality of the sound and picture greatly influenced by the positioning, quality and state of repair can be of your external aerial.
Your TV receives signals from the video recorder (VCR) like another TV station. You have to select a channel number on your TV and tune it in so that you may watch video tapes. If you connect a monitor or a TV set equipped with RCA terminal this necessary, simply select the AV mode on your TV. Make that you have installed correctly your VCR as described earlier video in this book. remote control.
Tunig a Videochanl OnyourTV Make sure that you have correctly installed your VCR and successfully tuned in video channel a dedicated on your Only carry out stages 5~8ifyoucannot obtain clear video playback 1 4. ~ which you wish to watch video's. Make on sure POWER be Select TV channel a 22 and 68. appears. The be following picture will displayed on the TV channel. number which you wish to watch video's. on a bright blue so that screen Store this channel on your TV.
This VCR The Turn on can easily menus are your TV set. be programmed by using the menus Press i. Press F or the desired Press POWER to turn your VCR. on displayed on screen. controlled from the REMOTE CONTROL HANDSET. The main appear menu on will the TV screen. G to select Press "i" to menu. menu. Press OK and press D remove usethmain the or E to select the sub menu.
Tunig n TVstaion Automaicly Make that you have installed your VCR and tuned a video The main channel on your TV as described earlier in this appear book. Press F sure Press i. Press OK to start the automatic correctly menu will the TV on The TV station table will appear when tuning G is screen. Press i to or tuning complete. process. save your settings. to select the ACMS. Switch your TV and select the channel you wish to watch videos. on Press POWER to turn Press OK.
In certain country broadcast signals may be too weak for your VCR's process to find or assign TV stations correctly. You must tune in these weaker broadcast stations manually in order for your VCR to store areas automatic of the tuning Manuly TVstaion Tunig n them. Press i. Press i. Press OK. The station table will Press AV to select C appear. (Standard stations) (Cable stations): Searching it locates The main appear will menu on the TV screen.
Tunig n TVstaion Manuly Press G to select STATION and press OK. Press D or E to select letters and numbers for the new station name. PressForGtomove back and forth between characters. Press i, confirm the Press i station the placement. again menus to remove from the TV screen. If you wish to manually tune other stations Your new TV station has been tuned into your VCR. 1-7. repeat stages now Press OK.
After TV stations into your VCR you may wish to change the order in which they are having to retune them against! The instructions given on this page will show you how you can simply move them into your desired order. tuning stored without Press i. Press i. Press D the The main menu on appear will the TV Press D screen.
After tuning TV stations into your VCR you may wish to delete a station. given on this page will show you how easily delete any unwanted TV The instructions stations. Delting& Selcting TVStaions Press i. Press i. The main stored TV stations: Stored TV stations can be selected in either of two ways. Press PROG. D or E to select different stations that are tuned into your VCR. Selecting appear Press F will menu on the TV or Press D screen.
You will eject video cassettes when your VCR is plugged into the mains. play back recordings from NTSC tapes (on PAL TV). Getting a better picture When a cassette is inserted and playback started, the automatic tracking function works to get the best possible picture automatically. If the quality of the recording is poor, repeatedly press or on the remote control to manually adjust the tracking until any distortions have been removed.
Picture search will only continue for about 3 minutes, after which your VCR will return to playback. During picture search, logic search, and CM Skip the sound is muted there will be some noise streaks on the picture. normal Playing a tape and During playback Slow motion Press STOP to end of Shuttle playback.
PAL Press i. To record The main appear menu on Press F will the TV or or screen. G to select E to select according to the COLOUR system used. Press i to remove the from the TV menus Allows PAL i Use when or MESECAM playing back a NTSC 3.58: Use when tape recorded in the NTSC system on PAL recording signals. TV. NTSC 4.43: Use when PAL: NTSC 3.58: Use when signals playing receiving or use back PAL when tape recorded in PAL system.
The clock in your VCR controls time, SetinghClock Manuly day Press i. Use the numbered Press F buttons on the remote control to alter or enter or G to select and date settings for your VCR. If you make a mistake press F or G and enter the correct details. the HOURS, MINUTES, DAY, MONTH and TIME DATE. Your are new clock settings stored and will appear on your video recorder's display. YEAR. Press OK. Press i. Please note your VCR 24 hour clock. uses a e.g.
Your VCR allows you to make recordings using a variety of simple methods : Instant Timer Recording (ITR) start recording immediately for a set period of time video cassette Timer Recording you may recordings these automatic Make VCR that you have installed your described earlier sure correctly as Insert with or a record at a later time may be set. video cassette protection tab into your VCR. in this book. (up to 1 month from the Press PROG. to or present).
Your VCR incorporates Long Play (LP) which enables you to record up to twice the amount video cassette. For example an E-180 will record up to 180 minutes using Standard Play (SP); using LP you will be able to record up to 360 minutes. Please note there will be a slight loss in picture and sound quality when using LP. of time InstaTimer Recording(ITR) on a Press LP if you wish to Press REC/ITR to start Press P/STILL to avoid record in recording. recording Standard Long Play Play.
You may set up to seven timer record events within one month of the current date. PLEASE NOTE! before setting the timer make sure that you have set the VCR clock correctly and you know which channels you have tuned TV stations on your VCR. Make sure that TV Press i. Press OK channels have been Press F tuned and stored. or G to select setting with a protection tab into LP CLK/CNT Press OK. CLEAR i PW ez REC/ITR OK usingOScreDplay you wish to record.
If timer record events Make If at a later date you wish to delete or change any of the settings in timer event memory you may do so without having to enter all the timer event information again. Simply display the timer event screen. Press D or E to select the event that you wish to delete or overlap... sure change. that the Press F to delete the event. Press OK to change; then press F or G to select Station, Date, Start and End times, and LP. Press D or E to enter the correct information.
Your VCR has an which if set will Energy Save feature place your VCR into an You may economic power save where the clock display will disappear. If you have programmed a recording, this feature mode of your VCR the Press POWER on the The VCR and clock will appear on the video recorder's display. Press POWER VCR on the and your VCR will go into Energy again the current time the TV on screen. recording is taking place these On Screen Displays will not be recorded will not work. VCR.
The TapeCountrMmyS Digital Tape Counter can be displayed on your TV screen instead of the time by pressing OK/CLK/CNT on the remote control. The Digital Tape Counter indicates the relative positions of recordings on the tape. ChildLock Press OK/CLK/CNT repeatedly until the counter is displayed The tape display on screen. counter will the actual counter to 0:00:00. Press PLAY or start is recording. tape will rewind and when automatically stop the counter returns to 0:00:00.
Automatic Memory Power Shut-Off This feature of your VCR enables you to Video Doctor (Self-Diagnosis) This feature informs you that there is switch off your VCR automatically after tape rewind has been completed. a with your VCR. These error messages will appear on the TV problem screen. Press POWER tape rewind. during The tape will rewind to beginning and your VCR will automatically Switch your VCR. on PressDorEtochecka the problem. Press i. HEAD STATUS switch itself off.
(easy) power off The sequence of "Stop Power Off is Eject (easy) repeat By pressing & holding ez REPEAT during play back, the holding section replayed twice automatically. ez ez(easy) Operations ez Rewind " matically by pressing During play ez back press POWER OFF. ez operated Your VCR will be ed as auto- POWER OFF. the operat- following ; During play back, & hold point ez press REPEAT at the where repeat play is to be concluded.
A second VCR (for tape copying) should be connected to the AUDIO IN and VIDEO IN terminals on the back of your VCR. General Power 100-240V~,50/60Hz. Power consumption Video Head System Approx. 14 Watts Double azimuth 4 heads, helical Tape scanning (CC490TW/CC460TW/CC450TW). Rotary 2 heads, helical scanning (CC290TW/CC260TW/CC250TW) 23.39 mm/sec (SP mode)/ 11.69 mm/sec (LP mode). Tape width 12.7 mm (0.5 inch).
Video Head Cleaning accumulating on Dirt Troubleshting become blurred the head after a long period of time can cause the playback picture to broken up. High quality video cassette tapes will not normally deposit dirt onto the video head, but old or damaged tapes might. Clean the video heads with a commercially CheckList or available video heads Check Symptom No picture no sound & Is the mains plug plugged cleaning tape.
P/N: 3834RP0068J