Colour Monitor USER GUIDE MANUEL D'UTILISATION MODEL : 99T
012W/En Introduction Thank you for purchasing an LG high resolution monitor. It will give you high resolution performance and convenient reliable operation in a variety of video operating modes. Features The 99T is a 19-inch (18.0 inches viewable ) intelligent, microprocessor based monitor compatible with most analog RGB (Red, Green, Blue) display standards, including IBM PC , PS/2 , Apple , Macintosh , Centris , Quadra , and Macintosh II family.
Monitor Registration The model and serial numbers These numbers are found on the rear of this unit. unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase. Staple your receipt to this are page. Date of Purchase : Dealer Purchased From : Dealer Address : Dealer Phone No. : Model No. : Serial No. : Notice All rights reserved.
Important Precautions This unit has been engineered improper On but and manufactured to assure your result in potential electrical shock or fire hazard. In order not to defeat the safeguards incorporated in this monitor, observe the following basic rules for its installation, use, and servicing. Also follow all warnings and instructions marked directly on your monitor. personal safety, use can safety 1. Use only the power cord supplied with the unit.
children from Keep monitor's cabinet dropping or pushing objects into the openings. Some internal parts carry hazardous voltages. Do not add accessories that have not been designed for this monitor. During lightning a unattended for an storm or when the monitor is to be left extended period of time, unplug it from the wall outlet. Do not the bring magnetic picture tube. devices such magnets as or motors near On installation 1. Do not allow do not place 2.
Connecting the Monitor On the back of the monitor are three plug-in connections; one for the AC power cord, and the others for the signal cable from the video card. 1. AC Power Connection One end of the AC power cord is connected into the AC power connector on the back of the monitor. The other end is plugged into a properly grounded three-prong AC outlet. The monitor's auto-sensing power supply can automatically detect 100-120V AC or 200-240V AC, 50 or 60Hz. 2.
A) Connection to any IBM VGA PC compatible system 3 shows the Figure signal cable connections from the monitor to the Video Graphics Array (VGA) port typical in an IBM PC or PC compatible. This also applies to any graphics video card for PC-CAD or workstation that has a 15 pin high density (3 row) D-Sub connector. 1.Power off both the monitor and PC. 2.
B) Connecting to an Apple Macintosh II, Figure 4 shows the connection separately purchased adapter. 1.Power OFF both to an Centris, and Quadra Apple Macintosh, using a the monitor and the PC. 2.Connect the 15 pin VGA connector of the supplied signal cable to the matching input on the back of the monitor. Tighten the thumbscrews to secure the connection. 3.
Notes on using the BNC connectors with other types of video cards. Follow the example that fits your needs. (BNC cables not included with Monitor.) IN CASE OF COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC ON GREEN): Connect R,G and B video signals to BNC of the monitor, respectively. receptacles on the back RGBH+VV Red Green Blue IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL: Connect R, G and B video signals and Composite sync BNC receptacles on rear panel, respectively.
Location and Function of Controls Front View Power ON/OFF button Digital Power (DPMS) Indicator Control Panel Contrast Brightness Adjustment Adjustment Control Control Rear View ID Label BNC AC Power Socket D-Sub Signal Connector 9 Signal Connectors
Control Panel Function All functions are OSD Exit Button adjusted from the microprocessor-based digital OSD Enter Button OSD Select /Adjustment Buttons on Button controls. Power Indicator Brightness Power On/Off Button Contrast the front of the monitor allow you to adjust the image an OSD menu. As you choose controls, the selected icon shows you what the chosen control will do. These pictures give you immediate understanding of the controls.
Contrast Control the display to the contrast desired. Move the thumbwheel located beneath this indicator to increase or decrease the display Adjust contrast. CONTRAST 100% 91.1kHz / 85Hz Power(DPMS) Indicator This Indicator lights up green when the monitor operates normally. If the monitor is in DPM (Energy Saving) mode (stand-by/suspend/ power off), this indicator color changes to amber. Power ON/OFF Button This button is used to turn the monitor On Screen on and off.
OSD You item Adjustment introduced to the the OSD system. were using Listed below items that and Selection Items are are OSD procedure of selection and the icons, icon names, and icon on the Menu. adjusting descriptions an of the shown Adjust Description Horizontal Size To H Increases the size of the 120 / width. Decreases the size of the SIZE 91.1kHz adjust image image. image. screen screen 85Hz OSD ADJ: : Horizontal Position To H POSITION 120 91.
OSD Adjust Description Side Pincushion To correct the SIDE Curves the PIN. 91.1kHz / image's edges image's edges Curves the 120 in and out of the bowing image. inwards. outwards. 85Hz OSD ADJ: : Trapezoid To correct Makes the TRAPEZOID the 120 91.1kHz / geometric screen image narrower screen OSD image wider at the top. ADJ: : Tilt To correct TILT 120 91.1kHz / image rotation. Tilts the screen Tilts the screen image left. image right.
OSD Adjust Description Moire Reduction MOIRE This item allows you to reduce the moire (Moire is caused by interference REDUCTION Horizontal Scan Line with the periodical screen). It is normally OFF. If you want to adjust it, select ON using the adjustment control and push the Enter dot OSD :ENT SEL: Button.
OSD Adjust Description Mode Recall If the monitor is MODE RECALL this control has : ENT in a factory effect. no SEL: OSD OSD operating preset mode, this control will reset the image to the factory preset mode. If the monitor is operating in a user mode, OSD Adjust This item lets you adjust the OSD position. When you have finished, use the exit ( ) ADJUST icon to retun to main menu to take another selection.
OSD Adjust Description Select Language To choose the control LANGUAGE language in which displayed. the names are SELECT OSD :ENT SEL: LANGUAGE SELECT ENDEFRESIT (ENGLISH) OSD SEL: : Mode Information To inform users of preset and user mode data. MODE This item INFORMATION provides information about the stored video modes. After OSD : ENT SEL: see MODE INFO. the desired video mode information. The mode information STANDARD 91.
Self Diagnostics The Studioworks 99T has a SELF DIAGNOSTICS OSD feature that pops up when there may be possible causes of non-operation. The OSD would highlight a possible reason the display is not showing an image. An example of this may be no signal cable attached. The when you turn on the monitor with monitor will display the SELF DIAGNOSTICS OSD with the CHECK INPUT SIGNAL. This would be a clue for you to check the NO DDC (Display DDC is a Data signal connections.
Video Memory Modes This multi-synchronous auto-scanning monitor can automatically detect and display several video modes falling within the monitor's scanning range of 30-96kHz Horizontal and 50-160Hz Vertical. In the PC area, this relates to a maximum flicker-free usable resolution of 1600x1200 at a non-interlaced refresh rate of 75Hz Vertical. For convenience, the monitor has a 40 mode memory, of which 12 modes come from the factory preset to popular video modes as described below.
A note about the video memory modes: There is total of 40 video memory modes, a generally more modes than you will use at any one time. Of these 40 modes, 12 are permanent, factory fixed modes that cannot be changed, and another 12 are set at the but may be overwritten to make more room. The remaining left blank (empty).
Energy Saving Design complies with the EPA's Energy Star program, which is a program designed to have manufacturers of computer equipment build circuitry into their products to reduce power consumption during This monitor time of non-use. This monitor also goes into its energy saving mode if you exceed the monitor's operating limits, such as the maximum resolution of 1600x 1200 or the frequency refresh rates of 30-96kHz horizontal 160Hz vertical.
Troubleshooting Symptom: Possible The Self causes: signal Symptom: Possible diagnostics message. cable is not connected. The power LED is illuminated amber. causes: Display power management mode. These is no sync signal. The signal cable is not fastened securely. Check the computer power and graphics adapter configuration. The frequency of the sync input is outside the operating range of the monitor.
Service 1. Unplug the monitor from the wall outlet and refer servicing to qualified service personnel when : The power cord or plug is damaged or frayed. Liquid has been spilled into the monitor. The monitor has been exposed to rain or water. The monitor does not operate normally following the operating instructions. Adjust only those controls that are covered in the operating instructions.
Specifications Sync signal types Priority Type H. Sync V. Sync 123 Separate sync Composite sync Sync. On Green H. Sync Sync V. Sync (N.C : no Signal H/V N.C N.C N.C connection) connector pin assignment 12345 1 5 6 10 11 Pin 1 23456789 15 Signal (D-Sub) Red Green Blue Ground Self-Test Red Ground Green ground Blue Ground No Pin Ground Ground SDA 10 11 12 13 14 V. 15 SCL H. Pin 1234 5 Color Signal (5 BNC) Red Green Blue Red Green Blue H. Sync (H or H+V) V.
Specification Picture tube 19 inch (18.0 inches viewable ), 90 degree deflection, Dark face, pitch High contrast AR-ASC(Anti-Reflection & Anti-Static 0.26mm dot Coating) . Sync Input Horizontal Freq. Vertical Input Freq. Form Signal input : 30kHz-96kHz : 50Hz-160Hz : Separate TTL, positive/negative Composite TTL, positive/negative : 15pin D-Sub (Automatic) (Automatic) connector/5 BNC connector Video Input Display Area Input Form Power : : 365.8 274.3 mm/14.4 x10.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction Features ...............................................................................................................1 Monitor Registration Notice ...................................................................................................................2 Trademark Acknowledgments ..............................................................................2 Important Precautions Safety...............................................................................
MONITOR LIMITED WARRANTY FOR THE UNITED STATES AND CANADA LG Electronics U.S.A., Inc. will repair or at its option replace, without charge, your product which proves workmanship under normal use, during the warranty period listed below from the date of original purchase. This warranty is good only to the original purchaser of the product during the warranty period as long as it is in the U.S. including Alaska, Hawaii and U.S.
