Video Cassette with Line Player Recording OWNER'S MANUAL MODEL : CL152TW/CL172TW CL182TW/CL112TW PAL NTSC BZ03 Before connecting, operating, please read this instruction booklet Internet or adjusting this product, carefully and completely. Address:http://www.lg.
Position your VCP so that no falls directly onto it. bright light or sunlight F e a t u r e s Precautions, Contes& Care should be taken not to expose your VCP to any unnecessary vibration, moisture, dust to or heat. Never except personnel. the back remove of your VCP as this can voltage and other hazards. If cover expose you to very high your VCP does not operate properly, please check the Troubleshooting Guide on page 14.
Each button on your VCP has the corresponding button control. (see page 6.) as its MODEL : same on function the remote MODEL CL152TW 12 3 CL172TW : 12 4 3 4 6 5 56 12 MODEL : 109 11 12 11 8 7 CL182TW 12 7 MODEL 3 456 8 CL112TW 12 POWER REW : 109 3 456 STOP/ EJECT FF PLAY REW OPR 12 11 10 9 78 P/STILL SYSTEM 12 11 10 1. Power 7. Record 2. 8. Pause/Still 3. (ON/OFF) Stop Tape Eject Cassette Compartment & 10. Function Indicators 5. 11.
The ToaTV Conecting on this page is the most common form of connection. However please check with yourmanufacturer's instruction books for specific information. Make sure all connections are made with both guidance given your VCP and additional appliance unplugged from the mains to avoid damaging your equipment. Connecting a VCP using Audio/Video cable is one of the best ways to achieve optimum sound and picture quality from video-tape playback (Recommended).
Your TV receives signals You have to select from the video a player (VCP) channel number like another TV station. your TV and tune it in so that you may watch video tapes. TV set equipped with AUDIO and VIDEO sockets this adjustment on If you connect a monitor or a will not be necessary, simply select the AV mode 1 Make 2 that you have installed your described earlier in sure Insert a video pre-recorded tape into your VCP and VCP press PLAY. this book.
Your video player (VCP) is designed so that almost all of its features CONTROL HANDSET. Some features RemotCnrl Locatin&Fu must also be on or on to on EJECT from Eject RECORD a of time, remove batteries, store them in a cool, dry place and period the SPEED manually adjust the tracking. out of the reach of children. tape. high speed picture play. PLAY To OPR SET is (see page. 9) batteries.
You You can can set the select the colour system used for playback and recording. system by pressing SYSTEM on the front of your VCP. Each time you press SYSTEM, a relevant indicator lights up for a few seconds in the display window. The system is changed as shown below. Source Mode PAL/ Recording AUTO PALMESECAM MESECAM Playback AUTO PALMESECAM NTSC Recording Playback aSystem Selcting System Change NTSC3.58 NTSC4.43 NTSC-PB NTSC3.58 NTSC4.
This VCP is How to designed to play back and record cassettes systems. You will only be able Getting When playbcktpe a better to load and eject using PAL, MESECAM, and NTSC video cassettes when your VCP is (3.58 or 4.43) colour plugged into the mains. picture playback started, the automatic tracking function works to get the best possible picture automatically.
Video Head Dirt blurred or but old or Cleaning a long period of time can cause the playback picture to become High quality video cassette tapes will not normally deposit dirt onto the video head, damaged tapes might. Clean the video heads with a commercially available video heads cleaning accumulating on the head after broken up. tape. 4 5 STILL Press P/STILL to still Visual search Press either FF a picture.
Other PlaybckFeturs 1 2 When the end of the Repeat playback If you want to play back tape repeatedly, Press a A.REPEAT. A.REPEAT indicator up in the display lights tape is reached, VCP automatically rewinds Logic search Hold down FF tape to the beginning and repeats playback continuously. to watch a REW of fast forward during If you want to release this function, press A.REPEAT again. reverse in the Release the button to return to or rewind. display window.
Make T a p e s Dub ing all connections sure damaging your 1 are made with both your VCP's and Television 2 Connect your VCP to another VCP as shown Press POWER to turn on Insert a blank video your VCP. tape with the record Insert protection tab into (recording) VCP. pre-recorded a source Aerial VIDEO Press STOP / EJECT to stop recording. your tape into another (playing) VCP. Simultaneously begin playback on another VCP and record AUDIO from the mains to avoid 4 3 below.
Your VCP allows you to make How to record 1 recordings connecting to TV a 2 Connect your VCP to as shown below. a TV Press POWER to turn equipped with AUDIO and VIDEO sockets. 3 on your VCP. Insert 4 a video cassette with the record protection tab Set the desired recording speed by pressing SPEED. into your VCP. Your external aerial must be in your TV.
5 7 6 Press REC to start Press P/STILL to avoid unwanted recording. recording scenes. During recording of TV programme you do not change the TV channel number on your TV. REC the Press STOP to end recording. indicator flashes in window. display PLAY Press P/STILL continue again recording. to REW FF STOP can be paused for up to 5 minutes. After 5 minutes your VCP will stop recording to Tapes prevent damaging the tape your VCP. or Press EJECT.
Check the following No picture ? Is the mains ? Is the TV switched ? ? & no before for service. calling plug plugged Have you tuned in watch video tapes on a General Power ..................................AC 110-240V, 50/60Hz Power consumption.............Approx. 10 Watts sound in and switched on ? ? ? format Dimensions video channel your TV to on page 5.) If you have used a Audio/Video cable to connect your VCP and TV have you selected the AV mode on your on ..................
P/N: 3834RP0064F