IT odel Numbers Numbers Model odel DC6121GRS DC9121GRS Libretto Istruzioni GB Instruction Manual FR Manuel d'Instructions DE Bedienungsanleitung NL Gebruiksaanwijzing RU Руководство SE Bruksanvisning по эксплуатации Part NO.
Instructions Manual INDEX RECOMMENDATIONS AND SUGGESTIONS CHARACTERISTICS ................................................................................................................... ........................................................................................................................................................... 17 18 INSTALLATION................................................................................................................................................
RECOMMENDATIONS AND SUGGESTIONS INSTALLATION The manufacturer will not be held liable for any incorrect or improper installation. The minimum hood is 650 safety distance between the cooker and the extractor voltage corresponds to that indicated on the rating to the inside of the hood. For Class I appliances, adequate earthing. check that the domestic power Connect the extractor to the exhaust flue ter 120 top from mm. Check that the mains plate fixed damages resulting mm.
CHARACTERISTICS Dimensions Components Ref. 1 Q.ty 1 Product Hood Components Body, complete with: Controls, Light, Blower, Filters 2 1 2.1 1 Telescopic Chimney comprising: Upper Section 2.2 1 Lower Section 9 1 Reducer 10 1 Flange Damper ø 150 14.1 2 Air Outlet Connection Extension 15 1 Air Outlet Connection ø 150-120 mm Ref. Q.ty 7.2.1 2 7.
INSTALLATION Wall Wall ? drilling and bracket fixing marking: Draw a vertical line the on supporting wall up to the ceiling, or as high as practical, the at centre of the area in which the hood will be installed. ? ? Draw a ing the ? ? horizontal line at 650 Place bracket 7.2.1 mm the wall on as above the hob. shown about 1-2 (notch) with the vertical reference centre mm from the ceiling or upper limit align- line.
Mounting ? Before ? ? body body, tighten the body mounting points. Hook the hood body onto the screws 12a. Fully tighten support screws 12a. Adjust screws Vr to level the hood body. cated ? the hood attaching on the hood two screws Vr lo- the hood Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to chimney using either a flexible or rigid pipe ø 150 or 120mm, the the choice of which is left to the installer.
ELECTRICAL CONNECTION ? Connect the hood to the mains ing ? a contact gap of at least 3 two-pole a switch hav- Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. Flue Upper exhaust flue Slightly widen the ? assembly two sides of the upper flue and hook them behind the brackets 7.2.1, seated. ? through mm.
USE Control Panel The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button. KEY LED FUNCTIONS Turns L 0/1 Light T1 0/1 Motor on First lighting and off. speed. When pressed T2 Speed on Second T3 Speed on Third speed. Speed Fixed Max. speed Flashing Intensive T4 on for about 1 seconds the motor is switched off. speed. speed. Suitable for the strongest cooking vapours and odours.
MAINTENANCE Grease filters CLEANING METAL SELF- SUPPORTING GREASE FILTERS Alarm ? ? reset signal Switch off the lights and extractor motor. Press button T3 for at least 3 seconds, until the leds start to flash. Cleaning ? the filters The filters are the LED S1 operation, ? washable and must be cleaned when lights or more usage. Remove the filters up or at least every 2 months of for particularly heavy frequently one at a time wards the back of the group and same time.
Activated charcoal filter ? The filter is not washable and cannot be (Recirculation version) regenerated. It must be replaced when led S1 signal will only light up when the extractor least every 4 months. The alarm motor is switched on. flashes Alarm ? signal at activation In Recirculation version at ? or a Hoods, the Filter saturation alarm can be enabled Disconnect the Hood Lights and the suction Motor off. using the Main switch or the double-pole on installation or later date.
Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered the by European Directive 2002/96/EC. 2. All electrical and electronic tion facilities 3. The correct products should be disposed of separately from the municipal waste stream via designated collecappointed by the government or the local authorities.