OWNER'S MANUAL DRYER Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times. ENGLISH DLE7100* DLG7101* DLE7150* DLG7151* DLE7000* DLG7001* MFL67652535 Rev.00_030821 www.lg.com Copyright © 2021 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS TABLE OF CONTENTS 3 SAFETY INSTRUCTIONS 35 SMART FUNCTIONS 5 7 35 35 IMPORTANT SAFETY INSTRUCTIONS GROUNDING INSTRUCTIONS 8 PRODUCT FEATURES 36 MAINTENANCE 36 9 PRODUCT OVERVIEW 9 9 Parts Accessories 10 INSTALLATION 10 10 11 11 13 14 15 16 18 20 24 25 Installation Overview Product Specifications Installation Location Requirements Clearances Leveling the Dryer Reversing the Door Installing the Side Vent Kit Venting the Dryer Connecting Gas Dryers Connecting Electric Dryers Fin
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USE Safety for a Dryer WARNING Fire Hazard Failure to follow safety warnings exactly could result in serious injury, death or property damage. Do not install a booster fan in the exhaust duct. Install all clothes dryer in accordance with the installation instructions of the manufacturer of dryer. WARNING: FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death or property damage.
SAFETY INSTRUCTIONS WARNING - RISK OF FIRE Install the clothes dryer according to the manufacturer’s instructions and local codes. • Clothes dryer installation must be performed by a qualified installer. • Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
SAFETY INSTRUCTIONS 5 IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: Installation •• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. •• Do not install or store this appliance where it will be exposed to the weather. •• Do not place items exposed to cooking oils in your dryer.
SAFETY INSTRUCTIONS Operation •• Read all instructions before using the appliance. •• Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. •• Do not reach into the appliance if the drum is moving. •• Do not allow children to play on or in the appliance.
SAFETY INSTRUCTIONS 7 GROUNDING INSTRUCTIONS WARNING Improper connection of the equipment-grounding conductor may result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt that the appliance is properly grounded. •• This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.
PRODUCT FEATURES PRODUCT FEATURES Easy-to-Use Control Panel An entire selection of user-friendly functions make operating the dryer easy. Easy-Access Reversible Door The wide-opening door provides easy access for loading and unloading. The door hinge can be reversed to adjust for installation location.
PRODUCT OVERVIEW PRODUCT OVERVIEW Parts Control panel Leveling feet Reversible door Lint filter Terminal block access panel (electric models) Gas connection location (gas models) Power cord location (gas models) Water inlet valve (on some models) Exhaust duct outlet Accessories Optional Accessories Drying rack (sold separately) No. 3750EL0001C Side vent kit (sold separately) Kit No. 383EEL9001B NOTE •• Visit www.lg.com to purchase accessories.
INSTALLATION INSTALLATION Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location. Check and choose the proper location Level the dryer Connect gas dryers Connect electric dryers Installation test Vent the dryer Gas dryer Electric dryer Plug in the power cord Test run Product Specifications The appearance and specifications listed in this manual may vary due to constant product improvements.
INSTALLATION 11 Installation Location Requirements WARNING Read all installation instructions completely before installing and operating the dryer! It is important that you review this entire manual before installing and using the dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages. The installation requires: •• A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors.
INSTALLATION Closet Ventilation Requirements Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet. One upper vent opening with a minimum opening of 48 sq. in. (310 cm2) must be installed no lower than 6 feet above the floor. One lower vent opening with a minimum opening of 24 sq. in. (155 cm2) must be installed no more than one foot above the floor. Install vent grills in the door or cut down the door at the top and bottom to form openings.
INSTALLATION 13 Leveling the Dryer 2 WARNING To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses. Failure to follow this warning may result in serious injury or death. Use an adjustable wrench to turn the leveling feet. Unscrew the legs to raise the dryer or screw in the legs to lower it. Raise or lower with the leveling feet until the dryer is level from side to side and front to back.
INSTALLATION Reversing the Door 4 WARNING THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure to follow the instructions below can result in damage to the dryer, property damage or injury to persons. Remove the 4 screws securing the hinges to the door frame. Remove the two plastic cover caps. Reinstall the hinges and cover caps on the opposite sides from which they were removed.
INSTALLATION 15 Installing the Side Vent Kit 3 WARNING •• Use a heavy metal vent. •• Do not use plastic or thin foil ducts. •• Clean old ducts before installing this dryer. •• To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses. •• Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons, or death. Preassemble a 4-inch (10.
INSTALLATION Venting the Dryer WARNING To reduce the risk of fire or explosion, electric shock, property damage, injury to persons or death when using this appliance, follow basic safety precautions, including the following: •• Do not crush or collapse ductwork. Failure to follow these instructions may result in fire or death. •• Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions may result in fire or death.
INSTALLATION 17 Routing And Connecting Ductwork NOTE Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork. Ductwork and fittings are NOT included and must be purchased separately. •• Use 4-inch (10.2 cm) diameter rigid, semi-rigid or flexible metal ductwork. •• The exhaust duct run should be as short as possible. •• Use as few elbow joints as possible. •• The male end of each section of exhaust duct must point away from the dryer.
INSTALLATION Connecting Gas Dryers WARNING To reduce the risk of fire or explosion, electric shock, property damage, injury to persons, or death when using this appliance, follow basic safety precautions. Gas Supply Requirements •• Use only a new AGA- or CSA-certified gas supply line (in compliance with the Standard for Connectors for Gas Appliances, ANSI Z21.24 • CSA 6.10) with flexible stainless steel connectors. •• Securely tighten all gas connections.
INSTALLATION 19 Connecting the Gas Supply •• Installation and service must be performed by a qualified installer, service agency, or the gas supplier. Failure to do so may result in fire, explosion, or death. •• Use only a new stainless steel flexible connector and a new AGA-certified connector. Failure to do so may result in fire, explosion, or death. •• A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. Failure to do so may result in fire, explosion, or death.
INSTALLATION Connecting Electric Dryers Electrical Requirements for Electric Models Only WARNING To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.
INSTALLATION 21 WARNING Connect the power cord to the terminal block. Connect each wire in the power cord to the terminal block screw with the matching colored wire. The terminal block wire colors are indicated in the manual. Failure to follow these instructions may result in a short or overload. Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) areas where local codes prohibit grounding through the neutral conductor.
INSTALLATION Four-Wire Direct Wire 7 Attach the white neutral wire to the center screw of the terminal block. •• Use UL-listed 4-wire #10 AWGminimum copper conductor cable. Allow at least 5 ft. (1.5 m) of wire to allow for removal and reinstallation of the dryer. 8 Attach the power cord ground wire to the green ground screw. 9 Tighten all screws securely. 1 10 •• A UL-listed strain relief is required. Remove 5 inches (12.7 cm) of the outer covering from the wire. Remove 5 inches (12.
INSTALLATION 23 5 WARNING Connect the power cord to the terminal block. Connect each wire in the power cord to the terminal block screw with the matching colored wire. The terminal block wire colors are indicated in the manual. Failure to follow these instructions may result in a short or overload. Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) areas where local codes prohibit grounding through the neutral conductor.
INSTALLATION Three-Wire Direct Wire 9 Reinstall the terminal block access cover. Hot (Black) •• A 3-wire connection is NOT permitted on new construction after January 1, 1996. •• A UL-listed strain relief is required. •• Use UL-listed 3-wire, #10 AWG-minimum copper conductor cable. Allow at least 5 ft. (1.5 m) length to allow for removal and installation of dryer. 1 Remove 3½-inch (8.9 cm) of the outer covering from the wire. Strip 1 inch (2.5 cm) insulation from each wire.
INSTALLATION 25 Installation Test (Duct Check) 4 Once you have completed the installation of the dryer, use this test to make sure the condition of the exhaust system is adequate for proper operation of the dryer. This test should be performed to alert you to any serious problems in the exhaust system of your home. •• This dryer features Flow Sense™, an innovative sensing system that automatically detects blockages and restrictions in dryer ductwork.
INSTALLATION •• Check the duct condition If the Flow SenseTM LED is turned on, check the exhaust system for restrictions and damage. Repair or replace the exhaust system as needed. Restricted or Blocked Airflow Avoid long runs or runs with multiple elbows or bends. NOTE When the dryer is first installed, this test should be performed to alert you to any existing problems with the exhaust duct in your home.
OPERATION 27 OPERATION WARNING To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the IMPORTANT SAFETY INSTRUCTIONS, before operating this dryer. Using the Dryer Lint Filter 1 Clean the Lint Filter If the lint filter has not already been cleaned, lift out the filter and remove the lint from the last load. This will help ensure the fastest and most efficient drying performance.
OPERATION Check the Lint Filter Before Every Load Group Similar Items Always make sure the lint filter is clean before starting a new load; a clogged lint filter will increase drying time. To clean, pull the lint filter straight up and roll any lint off the filter with your fingers. Do not rinse or wash the filter to remove lint. Push the lint filter firmly back into place. See Regular Cleaning for more information.
OPERATION 29 Control Panel DLE7100*, DLG7101* 1 2 3 4 DLE7150*, DLG7151*, DLE7000*, DLG7001* 1 2 1 POWER Button Press to turn the dryer ON. Press again to turn the dryer OFF. NOTE Pressing the POWER button during a cycle will cancel that cycle and any load settings will be lost. 2 Cycle Selector Knob Turn this knob to select the desired cycle. Once the desired cycle has been selected, the standard presets are shown in the display.
OPERATION DLE7100*, DLG7101* 8 11 9 12 10 13 DLE7150*, DLG7151*, DLE7000*, DLG7001* 8 11 9 12 8 Clean Filter Reminder The display will show Clean Filter when the dryer is turned on as a reminder to check the filter. It turns off when the START/PAUSE button is pressed. 9 C ycle Completion Indicator with Check Filter Reminder This portion of the display shows which stage of the drying cycle is currently underway (Dry, Cool).
OPERATION 31 Cycle Guide Cycle Bedding Fabric Type Comforters, pillows, shirts Heavy Duty Jeans, heavyweight items = default setting = allowable option Dry Level Normal Dry Adjustable Normal Dry Adjustable Normal Dry Normal Work clothes, corduroys, etc. Perm.
OPERATION Sensor Dry Cycles Manual Dry Cycles Sensor dry cycles utilize LG’s unique dual sensor system to detect and compare the moisture level in clothes and in the air and adjust the drying time as needed to ensure superior results. The dryer automatically sets the dryness level and temperature at the recommended setting for each cycle. The estimated time remaining will be shown in the display. NOTE Use manual dry cycles to select a specific amount of drying time and a drying temperature.
OPERATION 33 Cycle Settings and Options Cycle Modifier Buttons SENSOR DRY cycles have preset settings that are selected automatically. MANUAL DRY cycles have default settings, but you may also customize the settings using the cycle modifier buttons. Press the button for that option to view and select other settings. Cycle Option Buttons The dryer features several additional cycle options to customize cycles to meet individual needs.
OPERATION Special Functions Some cycle option buttons also activate secondary functions. These special functions are marked with an asterisk (*). Press and hold the option button marked with the special function to activate it. * Control Lock Use this option to prevent unwanted use of the dryer or to keep cycle settings from being changed while the dryer is operating. Press and hold the button marked *Control Lock for 3 seconds to activate or deactivate the Control Lock function.
SMART FUNCTIONS 35 SMART FUNCTIONS Using Audible Diagnosis to Diagnose Issues LG ThinQ Application Installing the LG ThinQ Application Search for the LG ThinQ application from the Google Play Store or Apple App Store on a smartphone. Follow instructions to download and install the application. LG ThinQ Application Features •• Smart Diagnosis™ Follow the instructions below to use the audible diagnosis method. •• Launch the LG ThinQ application and select the Smart Diagnosis™ feature in the menu.
MAINTENANCE MAINTENANCE Regular Cleaning WARNING To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following: •• Unplug the dryer before cleaning to avoid the risk of electric shock. Failure to follow this warning may cause serious injury, fire, electric shock, or death. Maintaining Ductwork Vent ductwork should be checked for lint buildup once per month and cleaned at least once per year.
Troubleshooting 37 TROUBLESHOOTING FAQs: Frequently Asked Questions Q: When I press a button, why does my dryer beep and then nothing happens? A: The Control Lock feature is turned on. To turn off Control Lock, turn the dryer on, then press and hold the button that has *Control Lock on or under it for 3 seconds. Q: Why does my dryer take so long to dry clothes? A: Proper airflow is critical to the efficient operation of clothes dryers.
Troubleshooting Before Calling for Service This dryer is equipped with an automatic error-monitoring system to detect and diagnose problems at an early stage. If the dryer does not function properly or does not function at all, check the following before you call for service. Operation Problem TM Possible Cause Solutions The Flow Sense indicator remains active after clearing the restriction in the venting.
Troubleshooting 39 Problem Possible Cause Solutions Clothes take too long to dry Exhaust ducts are blocked, dirty, or duct run is too long. Confirm that the exhaust duct is properly configured and free of debris, lint, and obstructions. Make sure that outside wall dampers can open properly and are not blocked, jammed, or damaged. Load is not properly sorted. Separate heavy items from lightweight items. Larger and heavier items take longer to dry.
Troubleshooting Problem Possible Cause Solutions Clothes take too long to dry Energy Saver option selected (on some models) If using the Cotton/Normal cycle, deselect the Energy Saver option. This option reduces energy use by adding an air dry section to the beginning of the cycle. Drying time is not consistent Heat settings, load size, or dampness of clothing is not consistent.
Troubleshooting 41 Performance Problem Greasy or dirty spots on clothes Possible Cause Solutions Fabric softener used incorrectly. Confirm and follow the instructions provided with your fabric softener. Clean and dirty clothes are being dried together. Use your dryer to dry only clean items. Soil from dirty clothes can transfer to the clean clothes in the same or later loads. Clothes were not properly cleaned or rinsed before being placed in the dryer.
Troubleshooting Problem Lint on clothes Excess static in clothes after drying Clothes have damp spots after a SENSOR DRY cycle. Possible Cause Solutions Excess static in clothes. Use a fabric softener to reduce static electricity. Be sure to follow the manufacturer’s instructions. Overdrying a load of laundry can cause a buildup of static electricity. Adjust settings and use a shorter drying time, or use SENSOR DRY cycles. Dryer is overloaded.
Troubleshooting 43 Error Codes Problem Possible Cause Solutions Error code: tE1 through tE7 Temperature sensor failure. Turn off the dryer and call for service. Display shows error code: PS (electric dryers only) Power cord is connected incorrectly. Check the connection of the power cord to the terminal block. *Flow SenseTM indicator shows four bars during the drying cycle or the display shows "d80" after drying Exhaust system is too long or has too many turns/restrictions.
Troubleshooting Problem Possible Cause Solutions The display shows d90, d95 The duct work is about 90%-95% blocked.(“d90” or “d95” error code is displayed for 2 hours only) Do not use the dryer until the exhaust system has been cleaned and/or repaired. Using the dryer with a severely restricted exhaust is dangerous and could result in a fire or other property damage. House exhaust system blocked. Check the outside dryer vent while the dryer is operating to make sure there is strong airflow.
WARRANTY (USA) 45 WARRANTY (USA) ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT REQUIRES YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT, UNLESS YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES” BELOW.
WARRANTY (USA) • Products with original serial numbers that have been removed, altered, or cannot be readily determined. Model and serial numbers, along with original retail sales receipts, are required for warranty validation. • Increases in utility costs and additional utility expenses. • Repairs when your product is used for other than normal and usual household use (e.g. commercial use, in s owner’s manual. • Costs associated with removal of your product from your home for repairs.
WARRANTY (USA) 47 PROCEDURE FOR RESOLVING DISPUTES: ALL DISPUTES BETWEEN YOU AND LG ARISING OUT OF OR RELATING IN ANY WAY TO THIS LIMITED WARRANTY OR THE PRODUCT SHALL BE RESOLVED EXCLUSIVELY THROUGH BINDING ARBITRATION, AND NOT IN A COURT OF GENERAL JURISDICTION. BINDING ARBITRATION MEANS THAT YOU AND LG ARE EACH WAIVING THE RIGHT TO A JURY TRIAL AND TO BRING OR PARTICIPATE IN A CLASS ACTION. For the purposes of this section, references to “LG” mean LG Electronics U.S.A., Inc.
WARRANTY (USA) Hearings and Location. If your claim is for $25,000 or less, you may choose to have the arbitration conducted solely on the basis of (1) documents submitted to the arbitrator, (2) through a telephonic hearing, or (3) by an in-person hearing as established by the AAA Rules. If your claim exceeds $25,000, the right to a hearing will be determined by the AAA Rules.
Memo
Memo
